R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Search: Posts Made By: pata
Showing results 1 to 10 of 10
Search took 0.01 seconds.
03-17-2014, 06:55 AM
Replies: 4,878
Views: 1,356,917
Posted By pata

Yes, not exactly but good info. I took a fast...

Yes, not exactly but good info.
I took a fast look to the stock radio and coulndt find anything the like so I see now it would need the custom firmware to try do something alike.

thank you.
03-15-2014, 04:35 PM
Replies: 4,878
Views: 1,356,917
Posted By pata

my friend got a gt3b stock and we are wondering...

my friend got a gt3b stock and we are wondering if there is any way to adjust the brake side "travel/power" on the fly without messing the endpoints or neutral points,and say assign it to an easy...
06-20-2013, 03:45 PM
Replies: 3,930
Views: 616,722
Posted By pata

I have read before about Tamiya 417 C-Hub...

I have read before about Tamiya 417 C-Hub fitting but can't say about Xray..eyeballing they look similar cant say its so bend back other than the 4 degree caster..

Cale79 can you actually confirm...
06-02-2013, 04:10 AM
Replies: 3,930
Views: 616,722
Posted By pata

Since I'm low post count and didn't want to spam...

Since I'm low post count and didn't want to spam all over, I couldnt make it to post the link properly so that was the only workaround I found to add them.


interesting, I was trying to make it...
06-01-2013, 04:30 PM
Replies: 3,930
Views: 616,722
Posted By pata

Finally got some time to work and finish my R1...

Finally got some time to work and finish my R1 stock by the manual setup. Running HW justock 10.5T class and nanotech 6000mah, 31T pinion and stock 84T spur looking for ratio 5, it just fits snug one...
03-08-2013, 05:25 AM
Replies: 3,930
Views: 616,722
Posted By pata

Sway bars look like they work better now still...

Sway bars look like they work better now still they feel like being too soft or shock springs to hard cause there is little compensation. They tend to bend before even start moving the arm.

Got...
03-07-2013, 01:10 PM
Replies: 3,930
Views: 616,722
Posted By pata

thank you grippgoat though of shims first but...

thank you grippgoat
though of shims first but found out later it was the outer hinge ping (wheel side) that was not totally free it moved but needed little more reaming to get free :blush: also...
03-07-2013, 05:28 AM
Replies: 3,930
Views: 616,722
Posted By pata

thank you .crispy for all the good information...

thank you .crispy for all the good information and pictures, now that I know the max. size I have to figure the ratio to choose to start buying spurs & gears.

I'm almost finished with the car...
03-02-2013, 04:34 PM
Replies: 3,930
Views: 616,722
Posted By pata

Thank you for all the answers and good info. ...

Thank you for all the answers and good info.

A couple more things...

- Could you post a side pic of your car with the installed servo saver so I can see the alignment with the steering bell...
02-28-2013, 12:08 PM
Replies: 3,930
Views: 616,722
Posted By pata

Hi there Got an R1 and will be running it in...

Hi there

Got an R1 and will be running it in HW justock blinky 10.5T class on outdoor asphalt in a wet/cold area.

Any recommended setup? I'm still holding on buying oils for diff and shocks......
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.