HOBBYWING TECH SUPPORT 1/8 & 1/10 OFF ROAD
Tech Regular
iTrader: (3)
Tech Regular
iTrader: (3)
Ok so I put the program box on, I have it set for 2wd mod buggy mode(running an 8.5) and the red light is blinking...but when I set the esc to 13.5 BL(blinky) the light is solid red and the wheels spin an balloon up like it should from an 8.5. Its like the programmer is confused or backwards..weird. Any body seen this before. Thanks
Tech Champion
iTrader: (4)
Ok so I put the program box on, I have it set for 2wd mod buggy mode(running an 8.5) and the red light is blinking...but when I set the esc to 13.5 BL(blinky) the light is solid red and the wheels spin an balloon up like it should from an 8.5. Its like the programmer is confused or backwards..weird. Any body seen this before. Thanks
Regional Moderator
iTrader: (1)
Thanks, thats what I did. I dropped it down to just under 4.4FDR and the motor stopped overheating. Surprised how much RPM this motor has.
Tech Legend
iTrader: (294)
Right now what you do guys feel are the best hobbywing escs for:
- 1/10 2wd buggy 17.5 blinky
- 1/10 4wd buggy open (5.5T motor)
would like High voltage BEC, If a version does the same thing but is smaller I am fine with that.
- 1/10 2wd buggy 17.5 blinky
- 1/10 4wd buggy open (5.5T motor)
would like High voltage BEC, If a version does the same thing but is smaller I am fine with that.
How do you guys like the smaller RX10 just stock The one that is the size of a quarter 80 amp its going into a F1 car
Tech Champion
iTrader: (2)
Xr10 pro 80A sorry forgot they were 2
Tech Champion
iTrader: (2)
I like mine, though I haven't had it long enough to fully appreciate it. It should work great in F1.
Tech Adept
iTrader: (3)
Is anyone else having problems with the data logging from the wifi module? It works sometimes then like right now, it says 0 on everything and 12.6v when I'm on a 2s battery.
Xerun v3.1 on firmware V3.2_140627_BETA.
Xerun v3.1 on firmware V3.2_140627_BETA.
Suspended
Hi everyone, joining the HW bandwagon.
I've just installed a new XR8 SCT, i have the wifi module but have a question, when trying to update firmware it wants me to disconect motor from ESC... is this needed or can i leave connected?
Really dont want to desolder it just to update.
I've just installed a new XR8 SCT, i have the wifi module but have a question, when trying to update firmware it wants me to disconect motor from ESC... is this needed or can i leave connected?
Really dont want to desolder it just to update.
Tech Fanatic
iTrader: (47)
I absolutely love Hobbywing! Ive had either a motor and esc since 2009, now I think I have about 5-6.. anyway.. I bought a Xerun XR8 SCT, hooked it up to a Trinity Certified Monster 17.5 for a fairly light SCT. the problem im having, (which I've heard from a couple others people) is that at initial throttle, it has no power... almost like its cogging, but smooth. I'm using a good sensor wire, not sure why its doing that. any advice?
Tech Fanatic
iTrader: (47)
you don't need to de-solder, just take off the pinion
Tech Fanatic
iTrader: (5)
I absolutely love Hobbywing! Ive had either a motor and esc since 2009, now I think I have about 5-6.. anyway.. I bought a Xerun XR8 SCT, hooked it up to a Trinity Certified Monster 17.5 for a fairly light SCT. the problem im having, (which I've heard from a couple others people) is that at initial throttle, it has no power... almost like its cogging, but smooth. I'm using a good sensor wire, not sure why its doing that. any advice?
I may be wrong here but I think the XR8 SCT likes 4 pole motors. The trinity is a 2 pole motor. That may account for your cogging.
Last edited by fievel; 07-14-2018 at 07:02 AM.
Tech Fanatic
iTrader: (47)