|
Originally Posted by Shawn68z
(Post 8749082)
You need to provide alot more information. Type of car, motor, gearing, track layout, and the ESC settings.
With the 119 (or 1224), you can easily Over time the motor, and it sounds like this is what you have done. Try upgrading back to the 119 software, and then start very conservative on the timing. We do know that step #54 Boost is 36 deg of timing. (Confirmed here on Rctech). Brushless motors will not run properly with more then 60deg of timing, they tend to run slow and make alot of heat. Shawn.
Originally Posted by COBRARACING
(Post 8748312)
quality wise yes perfromance similar.Also better hall sensor board which is designed by michael .
What some of you may not know the motors are actually designed by michael at hobbywing and then manufactured in a part owned hobbywing factory |
Originally Posted by guinnes.s
(Post 8544130)
this are the setting that i used for first time at my racing club.
110119 with sp13.5 v3 at 7.4 fdr ,max temp 72c 4 DRRS 8 9 boost timing 55 10 turbo slope 24 12 turbo timing 30 13 start rpm 2000 14 turbo delay 0.4 timing acc 200 the car felt really quick in the infield and at beginning of the 30 metre straight,but the turbo did not felt to have any punch.what setting could help? thanx
Originally Posted by sizheng
(Post 8544270)
You almost used up timing in boost, 2000+200*55=13000 , and with 7.4 FDR, the speed of your car is only 20km/h at this RPM.
Originally Posted by COBRARACING
(Post 8748312)
quality wise yes perfromance similar.Also better hall sensor board which is designed by michael .
What some of you may not know the motors are actually designed by michael at hobbywing and then manufactured in a part owned hobbywing factory does mean the hw would be the same?any suggestions. |
Right the workout maths is right, but that does not mean that the motor stops pulling once all the timing is used up... 13000 RPM would be where no more timing is added but the motor will continue to accelerate, so that's not a right answer there.
I run 50/18 have 200ACC and start at 2000RPM the elogger logs my max RPM on a 13.5 at 45000 using your maths my car would only be doing 12000 RPM as the boost stops this plainly is NOT the case so please lets get some correct facts / maths on here. |
is the firmware with the elogger out yet?
|
wait a minute. The boost (timing) and turbo (additional timing, with 'boost' as preliminary) are indicated in steps and not in degrees?
Can someone define how much 1 step represent in degrees? Thanks |
Originally Posted by cheapskate.brok
(Post 8750289)
wait a minute. The boost (timing) and turbo (additional timing, with 'boost' as preliminary) are indicated in steps and not in degrees?
Can someone define how much 1 step represent in degrees? Thanks |
Is it just me or has battery usage been dropped dramatically with the new software? Right now I'm only using 1.4A per 5min race with my 17.5t as I remember using at least 2A with the old firmwares.
|
Originally Posted by tdunster
(Post 8750327)
If it's linear then 1 step = 0.66 degrees and 1 degree = 1.5 steps.
true is 1 = 1° break through from angelo manual "with the precision of 1 degree steps." |
I dont know how to update the firmware on my LCD programming box, please help
|
Originally Posted by SammyZ
(Post 8751345)
I dont know how to update the firmware on my LCD programming box, please help
choice Device & 2 in 1 program box Software page had button Upgrade click will ok ! |
Originally Posted by flashrevolution
(Post 8750526)
false!
true is 1 = 1° break through from angelo manual "with the precision of 1 degree steps." The last released FW to use degrees is 1224. Cheers, Shawn. Ps. Besides, I am running 0119 with 15deg Endbell, 60 Boost, 20 Turbo. 95 Deg? My motor would be running backwards. |
Originally Posted by irgo
(Post 8749281)
64Deg on V3.0_110211(213)
Great, bringing up FW that isnt released yet. Lets keep our discussions to FW that has been publically released shall we? ;) Shawn. |
Originally Posted by irgo
(Post 8749281)
64Deg on V3.0_110211(213)
Oh frack it, it's just the one thing! I can't be bothered to ask any more..... :deathstar |
Originally Posted by flashrevolution
(Post 8750526)
false!
true is 1 = 1° break through from angelo manual "with the precision of 1 degree steps." |
Originally Posted by RC MARKET
(Post 8751419)
go to hobbywing web site download update USB Link V1.63
choice Device & 2 in 1 program box Software page had button Upgrade click will ok ! |
| All times are GMT -7. It is currently 03:23 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.