Originally Posted by irgo (Post 8529881)

Officially from Hobbywing

USB Link Software (11/1/19)(2008/10/14)
http://www.hobbywing.com/english/downloads.asp


Question :
1) How to returned this Latest LCD firmware to the Previously?
2) will Latest LCD Firmware work's with the First SuperCharged Esc Firmware?
3) RPM we would like to see it from LCD ?

Originally Posted by sizheng (Post 8529354)

So for those friends can not read Chinese but can't wait for the English instruction , please note the following changes.

1. Boost timing and turbo timing degree totally 60. This makes the setting of timing degree more accurate.(boost 0-60, turbo 0-40,if total degree more than 60,some of degrees are merged.)
2. Turbo slope rate has 6 options, which can adjust the speed of releasing total turbo timing.
3.boost timing acceleration (timing punch) from 50 to 750 RPM/degree.

Hope this can help you. Sorry for my English not good.

Originally Posted by dameetz (Post 8530166)

I just downloaded Hobbywing_USB_Link_setup_V1.63_110119......however I can't see the 0119Stock on the dropdown menu, the usual stock fw are there like 1224.

Originally Posted by dameetz (Post 8530166)

I just downloaded Hobbywing_USB_Link_setup_V1.63_110119......however I can't see the 0119Stock on the dropdown menu, the usual stock fw are there like 1224.

Originally Posted by dameetz (Post 8530206)

Nevermind,I just got now. Will be testing it later on.

Originally Posted by smilekt (Post 8531024)

me also ... how do you solve ?

Originally Posted by dameetz (Post 8531076)

Right click....run in asministrator mode.....now you can see from the dropdown menu. Ok.

Originally Posted by M7H (Post 8522006)

I've read this remark earlier, to also set reverse to 100%, even if you don't use reverse, but I can't feel any difference under braking, so I think this was a bug in any of the earlier firmware versions.
Shawn, do you feel a difference?
Also with flashing the ESC, some say you have to flash it 2 times, is this still needed?

Originally Posted by terryh (Post 8528765)

I want to try a Hobbywing 13.5t motor, but am struggling to find one to buy! I dont want to buy from Ebay really as I'm not sure that I will be actually buying a Hobbywing, so would rather a genuine source.

Can anyone point me in the right direction.

Originally Posted by 2wdrive (Post 8528981)

Is that the new HW motor with the sensorport to the side and the solder plugs?

Originally Posted by cherry2blost (Post 8531343)

Hi Terry we have the gunmetal 13.5's in stock for immediate delivery if it helps...

http://www.racersinexile.org.uk/Brus...91_372228.aspx

Sorry for my enforced absence however my wife has been diagnosed with a degenerative brain/nerve disorder and my studies have taken up the rest of my time. I am here to help if you need it(PM) but guess Cobra has it all pretty much covered. We will take the time to destruction test the new software to see how far we can push the equipment and update you soonish.

Originally Posted by guinnes.s (Post 8529293)

... well the new version as been up from this morning 10:00 UK time,i did install it and the 0119 is there ,flashed both the programmer and esc. COBRARACING do you have any tips to give on this new soft version with 13.5 motors?? ...

Originally Posted by sizheng (Post 8529393)

... Boost 40, turbo 20, turbo ramp 24degree/0.1s, start rpm 3000, step 300rpm. Fdr is important , but it depands on your motor and the layout,if straight not very long using a bigger Fdr is better.

Originally Posted by COBRARACING (Post 8530163)

... recommend to wait until there instructions are ready ...

Originally Posted by terryh (Post 8531370)

Can you bring one with you to Maritime this week? Assuming your going to be there....