Hobbywing ESC's
#646
Tech Apprentice
iTrader: (16)
I am having a problem with the 35A esc with the 9T. I have the combo in a 2wd buggy for several months now and just recently after a lap or two in a heat it slows down to about a crawling speed for a few seconds then returns to normal and it will happen again within the same heat. The motor and esc are not even warm when I take it off the track, so I don't think its thermaling.
Also this problem does not happen every heat.
The lipo is fully charged before each heat and I've ran the same lipos in my SC without any problem.
Anyone have any ideas?
Also this problem does not happen every heat.
The lipo is fully charged before each heat and I've ran the same lipos in my SC without any problem.
Anyone have any ideas?
#647
Tech Fanatic
iTrader: (6)
Just got to run my 150A esc today for the first time and I had a blast driving it. My question is with the programing card. On the pc I set up 3 different profiles and can save all the different settings to the esc all at once by hitting the apply button. When setting the esc w/ the programing card, it doesn't set all the settings for the chosen profile all at once does it?? I have to choose the profile and then go thru each setting and ok it to make the change to the esc. Is this correct or can I somehow apply all the saved profile settings at once??
#648
where to buy?
Where is a good place to buy the 150a systems? I'm looking for the m6b combo. Thanks.
#649
Tech Apprentice
xerun 80 amp esc
i just ordered one of these my mmp died last week i as going to get another but i seen the hobbywing 80a xerun for 66.00 i said what the heck i have the lcd programer buddy had 2 gave me one its going in my slash 2wd right now im using my 4074 tacon 2150 on 3s geared for 40 mph im going to get a sensored motor next a 2700kv or a 3300kv
#650
has anyone heard of or ran a bullistorm 120a Esc? is it any good and or a knockoff of a HW
thanks, D
thanks, D
#651
There was another thread, "Cheap power systems" I believe, where someone had tested them and confirmed they were a rebadged HW. Search for the thread and it should have some info
#652
Tech Apprentice
Less quality (when you sold the wires, the little cup move easily because it's not a high temperature tin like on HW Xerun or other ESC) so maybe it would not last like a HW.
#653
Tech Regular
iTrader: (14)
HW 150a esc issues
Hey guys I just got a HW 150a esc I updated the firmware to the newversion and put it in my sc10 4x4 with a cc 3800 and turnigy nano tech 5100 saddle packs and using a Flysky GT3B TX.
However now I have 2 issues:
First it doesnt seem like the brakes are working. The drag brake kicks in but that seems to be the only brakes I have.
Settings:
Forward and Brake only
Rev set at 100%
Drag at 60%
Initial breaking at drag
I have tried it with For/Brake/Rev setting also.
2nd issue is I have a ton of servo lag. When I hit the throttle and turn at the same time it lags badly, and the more throttle I give it the worst it becomes. Right now at its worst its about a sec of lag when I give it full throttle from a dead stop. It even does it when there is no load on the truck (upside down). My servo is a Hitec 5645MG.
I haven't had either one of these problems until I changed escs, CC MMM and Sidewinder. I have tried putting a capacitor on the 3rd channel (16v 4700uf) to help a glitching issue like I had to with my sidewinder and it didnt help.
Thanks for the help.
However now I have 2 issues:
First it doesnt seem like the brakes are working. The drag brake kicks in but that seems to be the only brakes I have.
Settings:
Forward and Brake only
Rev set at 100%
Drag at 60%
Initial breaking at drag
I have tried it with For/Brake/Rev setting also.
2nd issue is I have a ton of servo lag. When I hit the throttle and turn at the same time it lags badly, and the more throttle I give it the worst it becomes. Right now at its worst its about a sec of lag when I give it full throttle from a dead stop. It even does it when there is no load on the truck (upside down). My servo is a Hitec 5645MG.
I haven't had either one of these problems until I changed escs, CC MMM and Sidewinder. I have tried putting a capacitor on the 3rd channel (16v 4700uf) to help a glitching issue like I had to with my sidewinder and it didnt help.
Thanks for the help.
#654
Can you post a link to the 150a esc you have? If it's the one I have, it doesn't work very well on 2s.
#655
Tech Regular
iTrader: (14)
http://www.hobbypartz.com/07e-c-xerun-150a-sd.html
Could I have punch and timing set too high?
#656
Tech Elite
iTrader: (14)
seems like the cutoff voltage is not accurately measuring the actual voltage, this is same with my 120A. I tried setting it @ 3.3V/Cell but when the cuttoff kicks in, i measured the actual voltage and its still 7.8V hmm... so i set it to 2.8 and the cutoff roughly kicks when its @ 3.1v.... Seems like a bug, hope HW will look into this... have 2.0 and 2.1version, will have to check if its the same with the 2.1 Version.
#657
Tech Elite
iTrader: (27)
http://www.hobbywing.com/product_show.asp?id=238
http://www.hobbypartz.com/07e-c-xerun-150a-sd.html
Could I have punch and timing set too high?
http://www.hobbypartz.com/07e-c-xerun-150a-sd.html
Could I have punch and timing set too high?
#658
Tech Apprentice
iTrader: (6)
http://www.hobbyking.com/hobbyking/s..._Car_ESC_.html
so this is a hobbywing esc?? anyone have one? how do they do?
so this is a hobbywing esc?? anyone have one? how do they do?
#659
will an sc10 be enough to run my tekin pro 4 4000kv on 2s and 3s? or should I step up to an sc8? Looking at replacing my castle mamba max as it is giving me problems and the hobby wing stuff seems to be problem free lately.
Also where is the best place to buy them with a chance at getting it within a week rather then 3 weeks???
Also where is the best place to buy them with a chance at getting it within a week rather then 3 weeks???
#660
Tech Regular
The SC8 would work allot better with a pro4. You should also take a look at the new SCT-PRO, which is only $5-10 more but can run sensored. The cheapest place to find it is Aliexpress.com for $82 shipped, but it would be longer then a week. I don't think there's any place that can you get you one in a week except hobbypartz, but there a little more in price and dont stock the SCT-PRO, only the SC8.
hope this helps,
Aravan.
hope this helps,
Aravan.