Go Back  R/C Tech Forums > General Forums > Racing Forum
Speed Run Electric (All Classes Welcomed) >

Speed Run Electric (All Classes Welcomed)

Like Tree3Likes

Speed Run Electric (All Classes Welcomed)

Old 03-06-2017, 12:54 PM
  #541  
Tech Addict
 
Join Date: Sep 2014
Location: Bay Area, Cali
Posts: 605
Default

Originally Posted by fdjizm View Post
Well... unsupervised on the internet again...
4070-CM 3210kv
I dont know of any ESC that can power that beast. Good luck finding one
tc4basher is offline  
Old 03-07-2017, 05:36 AM
  #542  
Tech Adept
 
fdjizm's Avatar
 
Join Date: Jan 2010
Location: NY/NJ
Posts: 135
Default

I buy crazy things, I'm not proud of it.
fdjizm is offline  
Old 03-08-2017, 05:13 AM
  #543  
Tech Apprentice
 
Join Date: Mar 2016
Posts: 89
Default

Originally Posted by fdjizm View Post
Yes, 6s motor as per TP power.
It's never going to see that voltage or RPM.
On a real run (load in a 10lb car) I'm probably seeing 20-21 volts, I don't see it passing 65k.
I've tested this motor on the Mgt7 with 6s, the XLX can't handle it and shuts down, you'll need to use well under a 1:1 ratio or have an extremely light car for it to work out!
MallenP30 is offline  
Old 03-08-2017, 05:39 AM
  #544  
Tech Adept
 
fdjizm's Avatar
 
Join Date: Jan 2010
Location: NY/NJ
Posts: 135
Default

Originally Posted by MallenP30 View Post
I've tested this motor on the Mgt7 with 6s, the XLX can't handle it and shuts down, you'll need to use well under a 1:1 ratio or have an extremely light car for it to work out!
Oh yea? does it spin too fast for the ESC or just tries to pull massive amps?
I feel like I was making progress just fine with my 2200kv motor, then I had to start browsing the internet LOL.
fdjizm is offline  
Old 03-08-2017, 06:17 AM
  #545  
Tech Apprentice
 
Join Date: Mar 2016
Posts: 89
Default

Originally Posted by fdjizm View Post
Oh yea? does it spin too fast for the ESC or just tries to pull massive amps?
I feel like I was making progress just fine with my 2200kv motor, then I had to start browsing the internet LOL.
Yes my guess is it tries to pull too many amps
MallenP30 is offline  
Old 03-08-2017, 06:19 AM
  #546  
Tech Apprentice
 
Join Date: Mar 2016
Posts: 89
Default

Originally Posted by MallenP30 View Post
Yes my guess is it tries to pull too many amps
I did run it successfully a few times with small gearing but only hit high 130's and the esc was super hot, therefore not getting the full potential at all
MallenP30 is offline  
Old 03-08-2017, 08:39 AM
  #547  
Tech Initiate
 
Join Date: Oct 2016
Posts: 34
Default

Originally Posted by MallenP30 View Post
I did run it successfully a few times with small gearing but only hit high 130's and the esc was super hot, therefore not getting the full potential at all
you think you can get the full potential out of it if you use one of thoes crazy mgm 1000$ esc
long island rc is offline  
Old 03-08-2017, 08:50 AM
  #548  
Tech Initiate
 
Join Date: Oct 2016
Posts: 34
Default

What would be better kv for a tp 3650 in a 2wd salsh on 6s.right now I am thinking the 2350kv or the 2060kv. Have the castle 2400kv right now around 110mph. These motors are 10mm longer than the castle and higher quality. So I am thinking I could get 120-125 and my goal is to break 130 evenuly.would I need a 4050 or4060 to do that or can I pull it off with the 3650
long island rc is offline  
Old 03-08-2017, 09:29 AM
  #549  
Tech Apprentice
 
Join Date: Mar 2016
Posts: 89
Default

Originally Posted by long island rc View Post
What would be better kv for a tp 3650 in a 2wd salsh on 6s.right now I am thinking the 2350kv or the 2060kv. Have the castle 2400kv right now around 110mph. These motors are 10mm longer than the castle and higher quality. So I am thinking I could get 120-125 and my goal is to break 130 evenuly.would I need a 4050 or4060 to do that or can I pull it off with the 3650
I'd go with the 4060 or the 4070, on 6s anywhere from 2200kv-2900kv, just depends on what you are looking for and how you gear it
MallenP30 is offline  
Old 03-08-2017, 11:48 AM
  #550  
Tech Initiate
 
Join Date: Oct 2016
Posts: 34
Default

Originally Posted by MallenP30 View Post
I'd go with the 4060 or the 4070, on 6s anywhere from 2200kv-2900kv, just depends on what you are looking for and how you gear it
4070 I think is a little over kill and I know jm speck has done 120 with a 3650 sized posidon motor and he said it can do more I might go 4060 but I feel 4070 is complete over kill for a 2wd. I would like to try and do it with the 36XX sized motor but I will move up to a 4050 or 4060 if you guys don't think it can be done.
long island rc is offline  
Old 03-08-2017, 12:54 PM
  #551  
Tech Addict
 
Join Date: Sep 2014
Location: Bay Area, Cali
Posts: 605
Default

Originally Posted by long island rc View Post
4070 I think is a little over kill and I know jm speck has done 120 with a 3650 sized posidon motor and he said it can do more I might go 4060 but I feel 4070 is complete over kill for a 2wd. I would like to try and do it with the 36XX sized motor but I will move up to a 4050 or 4060 if you guys don't think it can be done.
130s in a 2wd Slash will be tough no matter what motor you run. I would go with a 40xx series for a pretty big slash.
tc4basher is offline  
Old 03-08-2017, 02:29 PM
  #552  
Tech Initiate
 
Join Date: Oct 2016
Posts: 34
Default

Originally Posted by tc4basher View Post
130s in a 2wd Slash will be tough no matter what motor you run. I would go with a 40xx series for a pretty big slash.
I am doing it because it is hard and beacues I want to have the fastest slash/rustler/stamped 2wd. And thanks I think I am going to go with the 4060 1950 or 2450.
long island rc is offline  
Old 03-08-2017, 02:56 PM
  #553  
Tech Addict
 
Join Date: Sep 2014
Location: Bay Area, Cali
Posts: 605
Default

Originally Posted by long island rc View Post
I am doing it because it is hard and beacues I want to have the fastest slash/rustler/stamped 2wd. And thanks I think I am going to go with the 4060 1950 or 2450.
Sounds like a good plan. Nothing wrong with a good challenge. Good luck with that.
tc4basher is offline  
Old 03-08-2017, 05:52 PM
  #554  
Tech Adept
 
fdjizm's Avatar
 
Join Date: Jan 2010
Location: NY/NJ
Posts: 135
Default

Originally Posted by MallenP30 View Post
I did run it successfully a few times with small gearing but only hit high 130's and the esc was super hot, therefore not getting the full potential at all
I'll give it a shot and put a current limit on the XLX.
I've been pulling about 220-230amps with the 5682 for 105mph.
fdjizm is offline  
Old 03-08-2017, 07:30 PM
  #555  
Tech Addict
iTrader: (24)
 
phildoggg's Avatar
 
Join Date: Feb 2009
Location: N.C.
Posts: 676
Trader Rating: 24 (100%+)
Default

There is a guy on yt running the 3200 in a rustler on 4s and i think he hit some good numbers..
phildoggg is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell or Share My Personal Information -

Copyright © 2023 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.