Chargers for everyone!!!
#1
Tech Master
Thread Starter
Chargers for everyone!!!
ok i have 3 chargers that i need to get rid of because of space isues
I have 1 integy 16x9v5
specs:
This is Integy's best AC/DC computerized charger. 16X9 is very easy to use and has all the great features of the 16X5. This unit is very versatile and accept three different kinds of power source; 12VDC, 100-120VAC or 200-240VAC. It has an internal 14 Amp switching power supply (18A peak output), 2 line LCD backlit dot matrix display, this unit can charge, discharge & cycle 4 to 8 cells, Ni-Cd & Ni-MH modes, charge 0.1A to 7.0A, discharge 0.1A to 20.0A, shows mAh, average voltage, peak voltage, charge time, discharge time, user selectable deltaV 3mV-20mV/cell, 0.80V discharge cutoff per cell during discharge. 16X9's internal 14A power supply is powerful enough to operate the INDI Dyno, together with the INDI Dyno, you can check motor rpm, break-in motors and drive lathe motor.
INDI 16 x 9
Pro-V2.5
Price set at$125
Next i have 2 pitbull x3's
specs:
Multiple rate charge mode selectable - allow you to customize your
charge profile by setting up to 3 different charge rates at set
milliamp points during the charge for max performance from your
packs
Pre-programmed for a variety of battery packs
Automatically stores up to 5 setups with up to 8 characyters each
that you select
21 system sounds alert you to battery charge status
Settings saved - charge amps, peak detect, text and audio effecs,
peak charge volts, charge time, milliamp hours and milliwatt hours
Charges NiCd and NiMH batteries
Black case with "Competition Electronics Turbocharge Pit Bull X3"
printed on the top of the case
Charger comes ready for the modeler's choice of charge and power
connectors or install the included alligator clips
Nonvolatile memory stores charge settings and data
Length: 5" (127mm)
Width: 3-7/8" ( 98mm)
Height: 2-1/2" ( 63mm)
Power Supply: 12-15VDC @ 7 amps
Maximum Power Supply Voltage: 15VDC
Cell types supported: NiCd & NiMH
Pack Size: 4-8 cells
Fuses: (2) 10 amp miniature flat-blade automotive type
Display: 2X16 character LCD, backlit
Programmable Peak Detect: .012-.192
Charge rate: .15-7 amps
Price set at $100 each
all three of these chargers look new so they would look esactly as you see them on the internet
I take paypal
Thanks
I have 1 integy 16x9v5
specs:
This is Integy's best AC/DC computerized charger. 16X9 is very easy to use and has all the great features of the 16X5. This unit is very versatile and accept three different kinds of power source; 12VDC, 100-120VAC or 200-240VAC. It has an internal 14 Amp switching power supply (18A peak output), 2 line LCD backlit dot matrix display, this unit can charge, discharge & cycle 4 to 8 cells, Ni-Cd & Ni-MH modes, charge 0.1A to 7.0A, discharge 0.1A to 20.0A, shows mAh, average voltage, peak voltage, charge time, discharge time, user selectable deltaV 3mV-20mV/cell, 0.80V discharge cutoff per cell during discharge. 16X9's internal 14A power supply is powerful enough to operate the INDI Dyno, together with the INDI Dyno, you can check motor rpm, break-in motors and drive lathe motor.
INDI 16 x 9
Pro-V2.5
Price set at$125
Next i have 2 pitbull x3's
specs:
Multiple rate charge mode selectable - allow you to customize your
charge profile by setting up to 3 different charge rates at set
milliamp points during the charge for max performance from your
packs
Pre-programmed for a variety of battery packs
Automatically stores up to 5 setups with up to 8 characyters each
that you select
21 system sounds alert you to battery charge status
Settings saved - charge amps, peak detect, text and audio effecs,
peak charge volts, charge time, milliamp hours and milliwatt hours
Charges NiCd and NiMH batteries
Black case with "Competition Electronics Turbocharge Pit Bull X3"
printed on the top of the case
Charger comes ready for the modeler's choice of charge and power
connectors or install the included alligator clips
Nonvolatile memory stores charge settings and data
Length: 5" (127mm)
Width: 3-7/8" ( 98mm)
Height: 2-1/2" ( 63mm)
Power Supply: 12-15VDC @ 7 amps
Maximum Power Supply Voltage: 15VDC
Cell types supported: NiCd & NiMH
Pack Size: 4-8 cells
Fuses: (2) 10 amp miniature flat-blade automotive type
Display: 2X16 character LCD, backlit
Programmable Peak Detect: .012-.192
Charge rate: .15-7 amps
Price set at $100 each
all three of these chargers look new so they would look esactly as you see them on the internet
I take paypal
Thanks
#2
Tech Master
Thread Starter
ttt
#3
Tech Master
Thread Starter
still available
#4
Tech Master
Thread Starter
up
Last edited by hpipro321; 10-08-2005 at 05:15 PM.
#5
Tech Master
Thread Starter
1 pit bull sold the other is still for sale
#6
Tech Master
Thread Starter
ttt
#7
Tech Master
Thread Starter
...
#8
Tech Master
Thread Starter
I still have one pitbull and a deal pending on the 16x9 v5
#9
Tech Rookie
how much would you go down to?
will you post to australia?
how much all together with shipping and for the charger in australian $'s
will you post to australia?
how much all together with shipping and for the charger in australian $'s
#10
Tech Master
Thread Starter
which one.. for the pitbull 100 is the lowest i can go and it would be pretty expensive to ship it , its like 30 bucks via fed-ex, for the integy 125 is also the lowest i can go and since the charger is bigger it would be about 35 dollars for shipping to australia
#11
Tech Master
Thread Starter
make offers on integy and pitbull
deal fell through
deal fell through
#12
Tech Master
Thread Starter
Originally Posted by hpipro321
make offers on integy and pitbull
deal fell through
deal fell through
#13
Tech Regular
I never received a reply to my request for a pic of the integy.
#15
Tech Master
Thread Starter
it looks exactly as you see it wut more is there to say