Vanquish Products / Axial SCX-10 Jeep JK Fully Loaded RTR - Tekin / Airtronics / VP
#1
Vanquish Products / Axial SCX-10 Jeep JK Fully Loaded RTR - Tekin / Airtronics / VP
I have up for sale an extra rig that was barely used at all, looking to find a good home because I don't use it. It is fully loaded and decked out ready for competition. Everything is VP on this rig, the only thing I would recommend this rig needs would be a winch whether it be a scale looking one or a servo winch (Tekin FXR is already installed for a winch controller) to truly complete. I built this rig to be able to run off of a 2s lipo hard case (aka race packs) because I have a bunch of them from other cars I have and they are really easy to find. It has the very very good wheel speed yet has tons and tons of torque from the 4 pole Tekin Pro4 motor. The setup could run on a 3s 11.1volt battery setup but it would be very very fast. One of the biggest trait about this rig is the fact that all weight is well below the shock towers and in between the frame rails which keeps the center of gravity point low and in the middle. Majority of the electronics are waterproofed in boxes with the exception of the servo and motor so the rig would be able to handle water.
Here's a list of what's on this rig and it's quite extensive.
Body:
- Vanquish Products Jeep JK Poison Spider Light Bar Mount
- Vanquish Products 6 inch Rigid Light bar (not wired up)
- Axial Jeep JK Rubicon 4 Door Compete Body (Orange/Black/Chrome painted)
- Axial Jeep JK Rubicon Front Bumper
- Axial Jeep JK Rubicon Rear Bumper with swing out
- RC Rock Armor Aluminum Ball Hitch
Chassis:
- Vanquish Products Front Chassis Mounted Servo (CMS) / Bumper Mount
- Vanquish Products Front Currie Panhard Mount for CMS setup
- Vanquish Products Rear Bumper Mount
- Vanquish Products Rock Sliders Mount (4 total)
- Vanquish Products Rock Slider Traxxas Box Mount
- Traxxas Stampede RX Boxes (2 one on each side of the slider mount)
- Traxxas Slash 4wd RX Box
- Wraith Battery Tray Modified to Fit in between Servo and Tranmission
- All Stainless Screws used everywhere
- Axial Aluminum Links used to brace shock towers and chassis
Axles:
- Vanquish Products Titanium 3/16 Upper Links, Panhard Link
- Vanquish Products Titanium Currie Steering Links
- Vanquish Products Titanium 1/4 Lower Links (Slides better because links are flush with rod ends)
- Vanquish Products SCX10 AR60 Front and Rear Axle Housings
- Vanquish Products SCX10 AR60 Front and Rear Shock/Link Mounts
- Vanquish Products SCX10 AR60 Front and Rear Upper Link Mounts
- Vanquish Products SCX10 AR60 Front and Rear Bearing Caps
- Vanquish Products SCX10 AR60 Front Wraith Diff Cover
- Vanquish Products SCX10 AR60 Rear Wraith 3D Diff Cover
- Vanquish Products SCX10 AR60 Front 8* C Hubs (Anodized Orange)
- Vanquish Products SCX10 AR60 Front 8* High Steering Knuckles (Anodized Orange)
- Vanquish Products SCX10 AR60 Rear Lock Outs (Anodized Orange)
Wheels / Tires:
- Vanquish Products SSZ-12 1.9 SCALER WHEELS Limited Edition (5 total matching spare)
- Vanquish Products 725 hubs (4 total)
- Vanquish Products 600 hub (for spare)
- RC4WD 1.9 Irok Tires Softer Compound (4)
- RC4WD 1.9 TSL Boggers Tire (1 mounted on spare)
Suspension:
- Vanquish Products Front and Rear Shock Hoops (Anodized Orange to Match Rig normally does not come in this color)
- Proline Scaler Powerstroke Shocks (4 all around and O-rings are upgraded to keep them from leaking)
Drive Train:
- Vanquish Products Transmission Housing (Anodized Orange)
- Vanquish Products Motor Mount/Gear Cover (Anodized Orange to Match Rig normally does not come in this color)
- Robinson Racing Steel One Piece Center Gear (Ends are heat treated to keep from breaking)
- Robinson Racing Steel Idler Gear
- 3racing Locked Spur Gear Mount
- Axial 80t Spur Gear
- Robinson Racing 24t Steel Pinion Gear
- MIP Front and Rear Steel Metal Drivelines
Electronics:
- Tekin Pro4 4000kv Sensored Brushless Motor
- 3.5mm Bullet Connectors are used to connect motor to ESC
- Deans connector Used for Battery connection
- Tekin RS Sensored Brushless ESC (Used to power the motor and is installed into the Slash 4wd RX box.
- Tekin FXR Brushed ESC (Pre-Installed, Programed to run a Winch, allows for proportional control of speed, and installed in Traxxas Stampede RX box with CC BEC)
- Castle Creation External BEC (Set to 6.0 Volts and installed in Traxxas Stampede RX box with FXR)
- Deans Micro connector used to connect two ESC together
- Servo Extension Used to allow boxes to disconnect from each other without opening them up (4 used in total)
- Hitec 7955tg Steering Servo (Ti gear & High Torque servo)
- Robotronics Aluminum 24t Servo Horn
- Airtronics MT-4 2.4ghz 4channel Remote (It is pre-programmed to run with this rig and winch is setup)
Now for the fun part the pictures. I can take any other pictures if needed for interested buyer.
SOLD
Here's a list of what's on this rig and it's quite extensive.
Body:
- Vanquish Products Jeep JK Poison Spider Light Bar Mount
- Vanquish Products 6 inch Rigid Light bar (not wired up)
- Axial Jeep JK Rubicon 4 Door Compete Body (Orange/Black/Chrome painted)
- Axial Jeep JK Rubicon Front Bumper
- Axial Jeep JK Rubicon Rear Bumper with swing out
- RC Rock Armor Aluminum Ball Hitch
Chassis:
- Vanquish Products Front Chassis Mounted Servo (CMS) / Bumper Mount
- Vanquish Products Front Currie Panhard Mount for CMS setup
- Vanquish Products Rear Bumper Mount
- Vanquish Products Rock Sliders Mount (4 total)
- Vanquish Products Rock Slider Traxxas Box Mount
- Traxxas Stampede RX Boxes (2 one on each side of the slider mount)
- Traxxas Slash 4wd RX Box
- Wraith Battery Tray Modified to Fit in between Servo and Tranmission
- All Stainless Screws used everywhere
- Axial Aluminum Links used to brace shock towers and chassis
Axles:
- Vanquish Products Titanium 3/16 Upper Links, Panhard Link
- Vanquish Products Titanium Currie Steering Links
- Vanquish Products Titanium 1/4 Lower Links (Slides better because links are flush with rod ends)
- Vanquish Products SCX10 AR60 Front and Rear Axle Housings
- Vanquish Products SCX10 AR60 Front and Rear Shock/Link Mounts
- Vanquish Products SCX10 AR60 Front and Rear Upper Link Mounts
- Vanquish Products SCX10 AR60 Front and Rear Bearing Caps
- Vanquish Products SCX10 AR60 Front Wraith Diff Cover
- Vanquish Products SCX10 AR60 Rear Wraith 3D Diff Cover
- Vanquish Products SCX10 AR60 Front 8* C Hubs (Anodized Orange)
- Vanquish Products SCX10 AR60 Front 8* High Steering Knuckles (Anodized Orange)
- Vanquish Products SCX10 AR60 Rear Lock Outs (Anodized Orange)
Wheels / Tires:
- Vanquish Products SSZ-12 1.9 SCALER WHEELS Limited Edition (5 total matching spare)
- Vanquish Products 725 hubs (4 total)
- Vanquish Products 600 hub (for spare)
- RC4WD 1.9 Irok Tires Softer Compound (4)
- RC4WD 1.9 TSL Boggers Tire (1 mounted on spare)
Suspension:
- Vanquish Products Front and Rear Shock Hoops (Anodized Orange to Match Rig normally does not come in this color)
- Proline Scaler Powerstroke Shocks (4 all around and O-rings are upgraded to keep them from leaking)
Drive Train:
- Vanquish Products Transmission Housing (Anodized Orange)
- Vanquish Products Motor Mount/Gear Cover (Anodized Orange to Match Rig normally does not come in this color)
- Robinson Racing Steel One Piece Center Gear (Ends are heat treated to keep from breaking)
- Robinson Racing Steel Idler Gear
- 3racing Locked Spur Gear Mount
- Axial 80t Spur Gear
- Robinson Racing 24t Steel Pinion Gear
- MIP Front and Rear Steel Metal Drivelines
Electronics:
- Tekin Pro4 4000kv Sensored Brushless Motor
- 3.5mm Bullet Connectors are used to connect motor to ESC
- Deans connector Used for Battery connection
- Tekin RS Sensored Brushless ESC (Used to power the motor and is installed into the Slash 4wd RX box.
- Tekin FXR Brushed ESC (Pre-Installed, Programed to run a Winch, allows for proportional control of speed, and installed in Traxxas Stampede RX box with CC BEC)
- Castle Creation External BEC (Set to 6.0 Volts and installed in Traxxas Stampede RX box with FXR)
- Deans Micro connector used to connect two ESC together
- Servo Extension Used to allow boxes to disconnect from each other without opening them up (4 used in total)
- Hitec 7955tg Steering Servo (Ti gear & High Torque servo)
- Robotronics Aluminum 24t Servo Horn
- Airtronics MT-4 2.4ghz 4channel Remote (It is pre-programmed to run with this rig and winch is setup)
Now for the fun part the pictures. I can take any other pictures if needed for interested buyer.
SOLD
Last edited by nissan_driver24; 11-18-2013 at 10:31 PM.
#3
free bump for a sweet rig
#4
one word.... WOW!!
#5
how much