FS: Slash Roller (w/radio+batteries+servo)
#1
Sold
Yep yep, finally got a box that would fit this monster. Here we go. First off, what the thing includes...
Tires:
-ProLine Bowties MC (clay) compound front and rear on Protrac wheels
*(See tread amount left in pictures)
•Note: Front tires have a small crack on the seam from sitting on the wall. It shouldn't be a big problem as long as you don't put in a crazy brusheless system
-ProLine Switch tires in M2 compound w/AKA soft closed cell inserts
•Used once or twice, unglued with acetone
-AKA Wishbones in Super Soft (mounted on Protrac wheels), they have been strapped with duct tape to prevent ballooning
•See pictures for wear
-Stock Traxxas wheels and tires
•See pictures for wear
A note for the tires: Each of them were washed and scrubbed down with Simple Green, and I did avoid getting water into the wheels
Radio/Receiver:
-Stock Traxxas Link 2.4ghz system. I can't be for certain that the radio works, so remove that from the price. The antenna on the actual radio wore down and partially broke off (the wire is fine otherwise, and the plastic piece stays on fine, just a little annoyance). The last time I got to check how it worked was in my SC10. It didn't seem to like high powered servos like the Savox SC-1258TG, and it constantly glitched. So, since I can't really test it... It will just be thrown in for free.
Servo:
-Hitech HS-5625MG servo
•Tested it, and I will test it again on video if you'd like. Much better servo compared to stock.
Batteries:
-2 3000mAh Traxxas 7 cell NiMH
Upgrades:
-Traxxas Red Aluminium Shock Caps
-Traxxas Red Aluminium Bell Crank (bearings)
-ProLine Protrac Kit
-ProLine Chassis Saver
-RPM Gear Cover
-Dubro Heavy Duty Servo Saver
-RPM Lower Shock Caps
-Traxxas TiNi Shock Shafts for the rear
-RPM front and rear Skid Plates
-Top shaft has a TiNi coated drill bit piece to hold the gear in place instead of a hollow metal pin
-RPM Bumper Mount
Misc:
-Chassis and gearbox have been dyed black
-Extra front hex NIP
-Front Tie Bar NIP
-Extra Dubro heavy duty servo saver
-Random ball ends
-Shock rebuild set (2 shocks)
-RPM Rear hub carriers (not installed)
-Extra Traxxas Red Aluminium Shock Caps (have been opened once before, sealed back up)
•The chassis has a small hole where the ESC used to be and has JB Weld placed in it. The plan was to be able to use the RPM chassis saver piece with the ProLine Chassis Saver, but I couldn't drill a hole in the aluminium so I figured I'd also make a quick note about that.
Another thing I have to say: Paypal only, no refunds as per the nature of this hobby, I won't be accepting trades.
Looking to get $150 shipped! Thanks for looking.
Pictures:
Rear:
Front:
Tires:
-ProLine Bowties MC (clay) compound front and rear on Protrac wheels
*(See tread amount left in pictures)
•Note: Front tires have a small crack on the seam from sitting on the wall. It shouldn't be a big problem as long as you don't put in a crazy brusheless system
-ProLine Switch tires in M2 compound w/AKA soft closed cell inserts
•Used once or twice, unglued with acetone
-AKA Wishbones in Super Soft (mounted on Protrac wheels), they have been strapped with duct tape to prevent ballooning
•See pictures for wear
-Stock Traxxas wheels and tires
•See pictures for wear
A note for the tires: Each of them were washed and scrubbed down with Simple Green, and I did avoid getting water into the wheels
Radio/Receiver:
-Stock Traxxas Link 2.4ghz system. I can't be for certain that the radio works, so remove that from the price. The antenna on the actual radio wore down and partially broke off (the wire is fine otherwise, and the plastic piece stays on fine, just a little annoyance). The last time I got to check how it worked was in my SC10. It didn't seem to like high powered servos like the Savox SC-1258TG, and it constantly glitched. So, since I can't really test it... It will just be thrown in for free.
Servo:
-Hitech HS-5625MG servo
•Tested it, and I will test it again on video if you'd like. Much better servo compared to stock.
Batteries:
-2 3000mAh Traxxas 7 cell NiMH
Upgrades:
-Traxxas Red Aluminium Shock Caps
-Traxxas Red Aluminium Bell Crank (bearings)
-ProLine Protrac Kit
-ProLine Chassis Saver
-RPM Gear Cover
-Dubro Heavy Duty Servo Saver
-RPM Lower Shock Caps
-Traxxas TiNi Shock Shafts for the rear
-RPM front and rear Skid Plates
-Top shaft has a TiNi coated drill bit piece to hold the gear in place instead of a hollow metal pin
-RPM Bumper Mount
Misc:
-Chassis and gearbox have been dyed black
-Extra front hex NIP
-Front Tie Bar NIP
-Extra Dubro heavy duty servo saver
-Random ball ends
-Shock rebuild set (2 shocks)
-RPM Rear hub carriers (not installed)
-Extra Traxxas Red Aluminium Shock Caps (have been opened once before, sealed back up)
•The chassis has a small hole where the ESC used to be and has JB Weld placed in it. The plan was to be able to use the RPM chassis saver piece with the ProLine Chassis Saver, but I couldn't drill a hole in the aluminium so I figured I'd also make a quick note about that.
Another thing I have to say: Paypal only, no refunds as per the nature of this hobby, I won't be accepting trades.
Looking to get $150 shipped! Thanks for looking.
Pictures:
Rear:
Front:
Last edited by NLpurplelambo43; 12-19-2012 at 03:06 PM.