***For Sale: 1/18 4WD BRUSHLESS Associated RC18R ARTR/UPGRADES/SPARE PARTS LOT***
#1
***For Sale: 1/18 4WD BRUSHLESS Associated RC18R ARTR/UPGRADES/SPARE PARTS LOT***
This is a lightly-used, adult-owned RC18R (with SHAFT driven chassis) that was only run indoors on carpet. It was never run outside, or on dirt or pavement. Check out the pic of the chassis bottom. I have installed a number of upgrades for it to make it competitive. The car drove like it was on rails at the 2010 Micro Indoor Off-Road Nationals, where I placed third in the A Main.
Things of note:
The body has a few cracks that were repaired with Shoe-Goo on the interior, and Oracal 951 clear adhesive vinyl on the outside. Very strong repairs!
The foam tires that are mounted are trued down to 42mm, but are split in a few places from racing. They are definitely usable, but perhaps only for practice.
The HS-65MG servo is mounted with a zip tie and the strongest 3M double-sided tape I could find. This tape is soft and extremely sticky. The servo does not move!
Prior to use, I extended the wires of the ESC a little, hence extensions were soldered on. No effect on performance.
NO TRANSMITTER, NO RECEIVER.
Upgrades installed:
MIP Super Differentials with metal outdrives front and back
MIP CVDs in front
Turnigy 24-35-4400kv brushless motor (torque monster!)
Castle Creations Mamba Micro Sport Speed Controller
Hitec HS-65MG servo
3Racing aluminum steering kit with improved servo saver spring
25mm fan
Painted Exotek Racing GTZ Body (for increased downforce)
RPM front bumper
3Racing aluminum threaded shocks
Associated Factory Team blue anodized aluminum motor mount/heat sink
Associated Factory Team Gold Springs in front
Upgrades included, but not installed
MIP CVDs for rear
T-Bone racing front bumper
One spare 3Racing aluminum steering linkage and servo saver spring
One spare assembled MIP Super Differential with metal outdrives
One set of Associated adjustable turnbuckles (unassembled in bag)
One pair Associated Gold Springs
One NEW HS-65HB Servo
One extra unpainted Exotek GTZ body
One Turnigy 30-40C 2s 1800 mAh lipo (6 charges on it)
One Turnigy 30-40C 2s 1600 mAh lipo (6 charges on it)
One Enerland 30C 2s 1200 mAh lipo (1 charge on it)
Included spare parts
4 assembled differentials
1 set of four 18R rubber tires with 8 runs on carpet
One pair of mounted foam tires (foam is very soft-white or pink compound-not sure...great grip!)
Original set of plastic shocks and springs
One front and one rear shock tower
Two sets of front suspension arms
One set of rear suspension arms
One set of body mount posts
One shock rebuild kit
Two 55-tooth and one 60-tooth spur gears
Lots of extra orange and black grease tubes for differentials
Two extra XP1016 steering servos (I think one has a damaged gear though)
Various miscellaneous parts too...
SOLD
Things of note:
The body has a few cracks that were repaired with Shoe-Goo on the interior, and Oracal 951 clear adhesive vinyl on the outside. Very strong repairs!
The foam tires that are mounted are trued down to 42mm, but are split in a few places from racing. They are definitely usable, but perhaps only for practice.
The HS-65MG servo is mounted with a zip tie and the strongest 3M double-sided tape I could find. This tape is soft and extremely sticky. The servo does not move!
Prior to use, I extended the wires of the ESC a little, hence extensions were soldered on. No effect on performance.
NO TRANSMITTER, NO RECEIVER.
Upgrades installed:
MIP Super Differentials with metal outdrives front and back
MIP CVDs in front
Turnigy 24-35-4400kv brushless motor (torque monster!)
Castle Creations Mamba Micro Sport Speed Controller
Hitec HS-65MG servo
3Racing aluminum steering kit with improved servo saver spring
25mm fan
Painted Exotek Racing GTZ Body (for increased downforce)
RPM front bumper
3Racing aluminum threaded shocks
Associated Factory Team blue anodized aluminum motor mount/heat sink
Associated Factory Team Gold Springs in front
Upgrades included, but not installed
MIP CVDs for rear
T-Bone racing front bumper
One spare 3Racing aluminum steering linkage and servo saver spring
One spare assembled MIP Super Differential with metal outdrives
One set of Associated adjustable turnbuckles (unassembled in bag)
One pair Associated Gold Springs
One NEW HS-65HB Servo
One extra unpainted Exotek GTZ body
One Turnigy 30-40C 2s 1800 mAh lipo (6 charges on it)
One Turnigy 30-40C 2s 1600 mAh lipo (6 charges on it)
One Enerland 30C 2s 1200 mAh lipo (1 charge on it)
Included spare parts
4 assembled differentials
1 set of four 18R rubber tires with 8 runs on carpet
One pair of mounted foam tires (foam is very soft-white or pink compound-not sure...great grip!)
Original set of plastic shocks and springs
One front and one rear shock tower
Two sets of front suspension arms
One set of rear suspension arms
One set of body mount posts
One shock rebuild kit
Two 55-tooth and one 60-tooth spur gears
Lots of extra orange and black grease tubes for differentials
Two extra XP1016 steering servos (I think one has a damaged gear though)
Various miscellaneous parts too...
SOLD
Last edited by MojoManDan; 06-15-2011 at 10:00 AM.
#2
More pics...
#3
***STILL AVAILABLE***
#4
YUP, STILL AVAILABLE TO A GOOD HOME!
#5
***There are a few offers on the table...but nothing concrete yet***
#6
SOLD