FS: FT-RC8T, SC10, Slash4x4Plat
#1
FS: FT-RC8T, SC10, Slash4x4Plat
The RC8T is the FT edition. Has very little use. Was a run a little with nitro, then to electric, then back to nitro, then it's current state.....ROLLER.
Has a set of PL HoleShots on PL black wheels. The tread is still good enough for running practice laps. I'm going to be including three, yes, 3, additional sets of tires/wheels with this roller.
One set is another set of PL HoleShots on PL white wheels. This set has a few laps on them, not much else. Tread is in great condition. These are the LPR version.
Second set is a of PL HoleShots on Mugen white 5-spoke wheels. Both the wheels and the tires are brand new, only mounted and glued. These are the XTR version.
Third sets is PL CrimeFighters on Mugen yellow 5-spoke wheels. These have been slightly run but the tread is still in great condition. Good for loamy, loose tracks too.
Price will be $350 with the 3 extra sets of tires/wheels, $300 without them.
New price:
$325 with the 3 extra sets of tires/wheels, $275 without them.
Lastly as it concerns this vehicle, the rear chassis brace is bent. Replace it for a few bucks or do yourself a favor and spend the $22 and get the King Headz one. I have them on my RC8B and they are the best there is IMO.
If you have any questions, please feel free to PM me here, email me, or even call/text me.
[email protected]
310-809-3131
As this is an international forum, if you're not local to southern california, shipping will be extra at the buyer's expense.
Thanx for viewing.
B.
Has a set of PL HoleShots on PL black wheels. The tread is still good enough for running practice laps. I'm going to be including three, yes, 3, additional sets of tires/wheels with this roller.
One set is another set of PL HoleShots on PL white wheels. This set has a few laps on them, not much else. Tread is in great condition. These are the LPR version.
Second set is a of PL HoleShots on Mugen white 5-spoke wheels. Both the wheels and the tires are brand new, only mounted and glued. These are the XTR version.
Third sets is PL CrimeFighters on Mugen yellow 5-spoke wheels. These have been slightly run but the tread is still in great condition. Good for loamy, loose tracks too.
Price will be $350 with the 3 extra sets of tires/wheels, $300 without them.
New price:
$325 with the 3 extra sets of tires/wheels, $275 without them.
Lastly as it concerns this vehicle, the rear chassis brace is bent. Replace it for a few bucks or do yourself a favor and spend the $22 and get the King Headz one. I have them on my RC8B and they are the best there is IMO.
If you have any questions, please feel free to PM me here, email me, or even call/text me.
[email protected]
310-809-3131
As this is an international forum, if you're not local to southern california, shipping will be extra at the buyer's expense.
Thanx for viewing.
B.
Last edited by BEAR5OH; 05-05-2011 at 03:46 PM.
#2
FT-RC8T, SC10, Slash4x4Platinum
Next in order, the SC10. This is a non-FT version. Acctually it's the RTR version but most of it has been undone, unscrewed, and opened up in order to improve up on it.
Modifications: Ball-Diff installed and it's smooth as silk. Not to mention, quiet. Although this was run a bit before the ball-diff went in, the tires were completely bald in the back. Rest assured, i'm giving you a rear pair that have seen about 5 minutes of time just testing stuff around the shop. Tney look practically brand spankin' new. Spur gear and snipper are in terrific shape. I'll also be including a few extra parts on one modification part that it will up to your discretion to use or not use. But its helps....ALOT! The CUDA chassis brace. You can find "fncuda* on RCTech.net. He manufactures these himself and these have been the goto part for even the earliest of SC10 right up until now. Along with the brace, some a-arms. 1 front and two rears. I may even have an extra stock battery hold down I can throw in too if you're ever prone to breaking them......I never have. It's the original stock one, not the nice Y or T shaped FT CF one from AE.
This is a roller. You'll need servo, esc, motor, and receiver. It will come with the stock/rtr style body which is the black KMC body. It's a bit banged up, but you'll get if I can find it.
Again, questions, please PM me here, email me, or call/text me.
[email protected] 310-809-3131
$100 for this roller and the extra stuff i've listed to go along with it.
Sale pending
B.
Modifications: Ball-Diff installed and it's smooth as silk. Not to mention, quiet. Although this was run a bit before the ball-diff went in, the tires were completely bald in the back. Rest assured, i'm giving you a rear pair that have seen about 5 minutes of time just testing stuff around the shop. Tney look practically brand spankin' new. Spur gear and snipper are in terrific shape. I'll also be including a few extra parts on one modification part that it will up to your discretion to use or not use. But its helps....ALOT! The CUDA chassis brace. You can find "fncuda* on RCTech.net. He manufactures these himself and these have been the goto part for even the earliest of SC10 right up until now. Along with the brace, some a-arms. 1 front and two rears. I may even have an extra stock battery hold down I can throw in too if you're ever prone to breaking them......I never have. It's the original stock one, not the nice Y or T shaped FT CF one from AE.
This is a roller. You'll need servo, esc, motor, and receiver. It will come with the stock/rtr style body which is the black KMC body. It's a bit banged up, but you'll get if I can find it.
Again, questions, please PM me here, email me, or call/text me.
[email protected] 310-809-3131
$100 for this roller and the extra stuff i've listed to go along with it.
Sale pending
B.
Last edited by BEAR5OH; 05-05-2011 at 03:46 PM.
#3
FT-RC8T, SC10, Slash4x4Platinum
Last in line, the SLASH 4X4 PLATINUM edition.
Pretty damn stock with the exception of putting a great setup into it and adding a few extras. Like: Integy heatsink & fan combo for the motor. The battery to ESC wires now have a pair of 4mm bullets to plug right onto a large amount of packs that use the two-pole direct plug in to the battery. Nice clean wiring. Added RMP nerfbars to both sides. These things are way way way tougher and stronger than the stockers. Center diff installed but I still have the slipperential set up if you'd like to change it back. Stock tires have very very very little use on 'em. This thing didn't get bashed. This was a track only car 99% of the time. The other 1% was working on jump trajectories and corrections in the back yard. Motor and ESC kept below 130 degrees
I've got some extra parts and stuff for this one too. Body mounts, half shafts, axles, extra hinge pins, etc....
Yes, the body is pretty damn ugly. It was made to be seen by me and only me when i'm at the track so it stands out in a crowd. It's a Desert Rat Carnage body, something that PL came out with almost immediately after the original Slash came out. I still have the fenders and bed sides if you want 'em. Or, gimme the body of your choice and i'll paint it up.
Any questions, please PM me here, email me, or call/text.
[email protected] 310-809-3131
Asking $300 all you'll need is a battery, a radio, and a receiver and you're in business.
The car is easily tunable for tracks and driving style. It should be good for just about anyone.
NEW PRICE:
$275 or best offer
B.
Pretty damn stock with the exception of putting a great setup into it and adding a few extras. Like: Integy heatsink & fan combo for the motor. The battery to ESC wires now have a pair of 4mm bullets to plug right onto a large amount of packs that use the two-pole direct plug in to the battery. Nice clean wiring. Added RMP nerfbars to both sides. These things are way way way tougher and stronger than the stockers. Center diff installed but I still have the slipperential set up if you'd like to change it back. Stock tires have very very very little use on 'em. This thing didn't get bashed. This was a track only car 99% of the time. The other 1% was working on jump trajectories and corrections in the back yard. Motor and ESC kept below 130 degrees
I've got some extra parts and stuff for this one too. Body mounts, half shafts, axles, extra hinge pins, etc....
Yes, the body is pretty damn ugly. It was made to be seen by me and only me when i'm at the track so it stands out in a crowd. It's a Desert Rat Carnage body, something that PL came out with almost immediately after the original Slash came out. I still have the fenders and bed sides if you want 'em. Or, gimme the body of your choice and i'll paint it up.
Any questions, please PM me here, email me, or call/text.
[email protected] 310-809-3131
Asking $300 all you'll need is a battery, a radio, and a receiver and you're in business.
The car is easily tunable for tracks and driving style. It should be good for just about anyone.
NEW PRICE:
$275 or best offer
B.
Last edited by BEAR5OH; 05-05-2011 at 03:46 PM.
#6
Tech Fanatic
iTrader: (75)
I'd be interested in buying your 3, yes 3 sets of wheels off you, if your willing to part out.
(sorry, it's my nature to be a smart#%!)
Or maybe just 2 sets of wheels so you have a set to sell with your RC8T
What would be your price for 2 sets? Probably the 2 sets with ofna 5-spoke rims?
- Justin
(sorry, it's my nature to be a smart#%!)
Or maybe just 2 sets of wheels so you have a set to sell with your RC8T
What would be your price for 2 sets? Probably the 2 sets with ofna 5-spoke rims?
- Justin
Last edited by Justin Bolin; 12-10-2010 at 01:31 AM.
#8
Tech Fanatic
iTrader: (75)
Hey Bear50h,
I'd like to buy your PL HoleShots on Mugen white 5-spoke wheels, XTR version, off you. Could you pm me a price for the 1 set of truggy wheels?
I just love how those mugen rims look on an RC8Te.
Pm me price or send to my email:
[email protected]
Ps,
Do you ever make it out to OCRC in Huntington Beach? I'm out in corona and I'll make it out there every so often for open racing. I usually take my all aluminum FLM Stampede out there with me.
Haven't been there in awhile, I recently bought an RC8Be and a factory team converted to brushless RC8t that I'll be looking to take out there soon.
I work retail so it's hard to get a routine for go out there. I usually stick to Pegasus hobbies in Montclair, and Milestone park out here in the 909. The milestone track for 1/10 scale is big and wide and they have a Baja 5 T/B track that's always fun to watch, race with my RC8e (I sold last week).
Free bump for a sweet truggy,
Justin
I'd like to buy your PL HoleShots on Mugen white 5-spoke wheels, XTR version, off you. Could you pm me a price for the 1 set of truggy wheels?
I just love how those mugen rims look on an RC8Te.
Pm me price or send to my email:
[email protected]
Ps,
Do you ever make it out to OCRC in Huntington Beach? I'm out in corona and I'll make it out there every so often for open racing. I usually take my all aluminum FLM Stampede out there with me.
Haven't been there in awhile, I recently bought an RC8Be and a factory team converted to brushless RC8t that I'll be looking to take out there soon.
I work retail so it's hard to get a routine for go out there. I usually stick to Pegasus hobbies in Montclair, and Milestone park out here in the 909. The milestone track for 1/10 scale is big and wide and they have a Baja 5 T/B track that's always fun to watch, race with my RC8e (I sold last week).
Free bump for a sweet truggy,
Justin
#9
PMs replied.
Please don't hesitate to make offers on any of this stuff.
If you want the truggy wheel n tire sets: $40 for the PL Holeshots (new) on new Mugen white 5-spokes; $27.50 per set on the used sets.
Payment is cash in person (Southern California) or PayPal. No, I don't require you to send as a gift or pay the fees.
Happy Holidays!
B.
Please don't hesitate to make offers on any of this stuff.
If you want the truggy wheel n tire sets: $40 for the PL Holeshots (new) on new Mugen white 5-spokes; $27.50 per set on the used sets.
Payment is cash in person (Southern California) or PayPal. No, I don't require you to send as a gift or pay the fees.
Happy Holidays!
B.
#11
Pending sales and prices
SC10 is still pending
Price changes for the Slash 4x4 Platinum and the RC8-T
If you are only interested in the 3 extra sets of truggy tires/wheels, prices are:
New PL Holeshots on white Mugen 5-spoke wheels - $35 + $5 shipping
Used PL Crimefighters on yellow Mugen 5-spoken wheels - $20 + $5 shipping
Used PL Holeshots on white PL wheels - $20 + $5 shipping
Of course if you want more than one set, i'll combine the shipping cost. No need to charge you more than what it costs to ship.
b.
Price changes for the Slash 4x4 Platinum and the RC8-T
If you are only interested in the 3 extra sets of truggy tires/wheels, prices are:
New PL Holeshots on white Mugen 5-spoke wheels - $35 + $5 shipping
Used PL Crimefighters on yellow Mugen 5-spoken wheels - $20 + $5 shipping
Used PL Holeshots on white PL wheels - $20 + $5 shipping
Of course if you want more than one set, i'll combine the shipping cost. No need to charge you more than what it costs to ship.
b.
#13
Interested in trades for the RC8t?
#15
Trades for the slash?