Pro LATHE 3 f.s. EVERYTHING you NEED to rebuild (PICS)
#1
Pro LATHE 3 f.s. EVERYTHING you NEED to rebuild (PICS)
This is a Trinity Pro Lathe 3 professional comm. lathe with LOTS OF accessories:
HISTORY:
I bought this lathe about 6 months ago and it has seen about 30 comm cuts and 2 new bits. The lathe
cuts perfectly, not much else to say about it I've never had any trouble with it's operation as long as the bit is good. I've always gotten a mirror like finish on all my comms. I bought a lot of accessories for the lathe, all of which are included.
I'm saving for a toy that I RIDE on, so a lot of my rc stuff has to go.
Comes with:
- Trinity Pro Lathe 3 (Black)
- slick zero bit carbide bit
- carrying case with 8 storage tubes, and custom foam spacing
- 4-cell panasonic 3000mah nimh SxS battery pack ( works gr8 all cells charge up fine)
- stock 20 turn associated slave motor
- rubber o-ring
- V-blocks AND BALL BEARING rollers completely interchangeable
- shim pieces for the bit
Additionally Includes:
- some misc armature shims, trinity teflon and brp brass oilite
- some new and some used brushes
- 2 comm grinding stones (red and green)
- 1 fiberglass comm pen (90%)
- 1 deluxe motor stand BLUE
- 1 bottle Slick/Zero comm cutting fluid (makes the comm so shiny, hurts your eyes 90% full)
- 1 NEW IN PLASTIC slick/zero carbide bit (best bit I've found)
- 2 new R/H carbide bits
- 1 used R/H carbide bit (dulled, can be sharpened but I'm too lazy)
- 1 pretty new LARGE sharpie black marker (hey don't laugh you'll need it)
I'd like to see $120 + $20 shipping OR B/O, priced to sell quickly. This setup
would easily cost 250 dollars if bough seperately, and this stuff is in great shape.
I WILL NEGOTIATE ON PRICE SO DROP ME AN EMAIL AT [email protected]
I also have a HUDY Ultimate setup system 1/10 touring with tons of accessories, a nice
electric tc3, available seperately. And an INTEGY octane 2 discharge tray for cheap, works
like new. And a nice RTR modded Emaxx with 2 sets of 7-cell 3300's
Thanks,
Randy
HISTORY:
I bought this lathe about 6 months ago and it has seen about 30 comm cuts and 2 new bits. The lathe
cuts perfectly, not much else to say about it I've never had any trouble with it's operation as long as the bit is good. I've always gotten a mirror like finish on all my comms. I bought a lot of accessories for the lathe, all of which are included.
I'm saving for a toy that I RIDE on, so a lot of my rc stuff has to go.
Comes with:
- Trinity Pro Lathe 3 (Black)
- slick zero bit carbide bit
- carrying case with 8 storage tubes, and custom foam spacing
- 4-cell panasonic 3000mah nimh SxS battery pack ( works gr8 all cells charge up fine)
- stock 20 turn associated slave motor
- rubber o-ring
- V-blocks AND BALL BEARING rollers completely interchangeable
- shim pieces for the bit
Additionally Includes:
- some misc armature shims, trinity teflon and brp brass oilite
- some new and some used brushes
- 2 comm grinding stones (red and green)
- 1 fiberglass comm pen (90%)
- 1 deluxe motor stand BLUE
- 1 bottle Slick/Zero comm cutting fluid (makes the comm so shiny, hurts your eyes 90% full)
- 1 NEW IN PLASTIC slick/zero carbide bit (best bit I've found)
- 2 new R/H carbide bits
- 1 used R/H carbide bit (dulled, can be sharpened but I'm too lazy)
- 1 pretty new LARGE sharpie black marker (hey don't laugh you'll need it)
I'd like to see $120 + $20 shipping OR B/O, priced to sell quickly. This setup
would easily cost 250 dollars if bough seperately, and this stuff is in great shape.
I WILL NEGOTIATE ON PRICE SO DROP ME AN EMAIL AT [email protected]
I also have a HUDY Ultimate setup system 1/10 touring with tons of accessories, a nice
electric tc3, available seperately. And an INTEGY octane 2 discharge tray for cheap, works
like new. And a nice RTR modded Emaxx with 2 sets of 7-cell 3300's
Thanks,
Randy