WTS?WTT HOT BODIES D8 WCE INSTALLED ALMOST NEW AND HUGE PARTS LOT
 

TRADED ALL GONE




Would trade for a Serpent 811 in nice condition.
I have a HB D8 with about 20 minutes of run time on it. Just like new. It has Tekno front and rear shock towers, 112mm rear shocks, M2c rear toe system, M2c hingepins front and rear. It has just about all the upgrades installed. it will include all the parts that were replaced. All the upgrades are new never run. Motor, pipe and sevos not included.
Here is a list of the upgrades installed: (ALL NEW NEVER RUN)
King Headz Aluminum upper streering Brace
Kyosho IFW416 6.8mm Hard Ball
Kyosho IFW104 Front Sway Bar set
Kyosho Steering Rod ends
Aluminum Steeri ng servo horn
67202 Light weight shock standoffs Front/Rear
67194 Light weight chassis 3mm(just installed,never seen the ground)
67625 Diif mount spacer
68182 7mm enginge mount set
67204 Light weight fixing balls
67172 WCE aluminum axles on all 4 corners
67174 WCE drive shafts 92mm on all 4 corners
67170 WCE center rear driveshaft 105mm
67176 WCE aluminum center drive shaft coupler
67202 Light weight shockstand offs front and rear
67197 Lightweight outdrives front and rear
67217 DCJ center driveshaft set front
Mugan E0124 Lower armshafts(captured outer hingepins)Front and rear
DYN687 Dynamite Cvd shaft boots
T-works Aluminum wing mount post
New radio tray, side guards installed(just installed tray, I stripped a screw)
New not installed HB aluminum rear carriers(old style)
Remember all the above is NEW never ran

It has a new jc yellow wing on it and a new jc black wing to come with it. Has a practice body in ok shape and a new custom painted jc hi flow body. Painted by Roly(you have to finish trimming.New bearing thew the whole car. They are readyroller bearings.Will come with clutch setup, including new springs and new clutch shoes. I will include all the original stock parts that came off of it, diff case new, arms new, (original chassis). And some loose spares that are new- arms, diff cases, ect

Asking $325 shipped OBO + paypal fees or send as gift or possible trade for serpent 811
I can add a 3 1/2 -4 gal JX NInja just pinched. You have to finish breaking in for $400 shipped + fees

pm with any questions

http://i276.photobucket.com/albums/k...8/100_2392.jpg
http://i276.photobucket.com/albums/k...8/100_2396.jpg
http://i276.photobucket.com/albums/k...8/100_2393.jpg
http://i276.photobucket.com/albums/k...8/100_2397.jpg
http://i276.photobucket.com/albums/k...8/100_2394.jpg
http://i276.photobucket.com/albums/k...8/100_2400.jpg
http://i276.photobucket.com/albums/k...8/100_2398.jpg
http://i276.photobucket.com/albums/k...8/100_2401.jpg
http://i276.photobucket.com/albums/k...8/100_2402.jpg
http://i276.photobucket.com/albums/k...8/100_2389.jpg
http://i276.photobucket.com/albums/k...8/100_2390.jpg
http://i276.photobucket.com/albums/k...8/100_2391.jpg

pics of ninja $100 shipped + fees
http://i276.photobucket.com/albums/k...8/100_2322.jpg
http://i276.photobucket.com/albums/k...8/100_2324.jpg
http://i276.photobucket.com/albums/k...8/100_2326.jpg

I also have a huge parts lot:

Complete set Front and Rear shocks (112mm rear)
Tony screws Kit complete
VP Pro air filter pack of 8 I think NIP
Throttle linkage set from a kit
M2C lower front and rear hingepins
67448 Blue shock spring
67391 Front hingepins plate
67384 Front suspension block
(2) HBC8045 clutch springs
(2) HBC8043 carbon clutch shoes
(3) HBC8009-1 Diff cases
(2) HBC8021 diff pads
67382 rear chassis brace mount
67383 rear chassis brace
67401 front chassis brace
67420 center diff mount cover
67419 center diff mount
67353 6 hole shock piston set
67386 front hub carrier set 10 deg.
67400 steering brace
67464 steering turnbuckle 5x30mm
67351 shockend/retainer set
67521 wingmount set
67388 front spindle set
67385 front lower arm set
67381 rear lower arm set
(2) 67515 shock maintance set
67350 shock boot set
(2) 67405 drive shaft 91mm
67407 center front drive shaft
67408 center rear driveshaft
set of side guards new , not in package
cvd condoms
dyn7687 dynamite cvd boots

http://i276.photobucket.com/albums/k...8/100_2403.jpg
http://i276.photobucket.com/albums/k...8/100_2404.jpg
$135 shipped + pp fees for the lot or will combine with buggy at a better price

Servos: will do $85 for the lot+fees
http://i276.photobucket.com/albums/k...8/100_2406.jpg
2- Airtronics 94361 in good shape. Worked fine the last time I used them. No cut or nicks $30 each or $55 for both
1- Airtronics 94773 in good shape, no nicks or cuts. Worked fine the last time I used it. $30 shipped
1- JR Z590M in good shape, no cuts or nicks. Worked fine the last time used. $15 shipped

added parts lot getting pics ready now.

I can vouch for this whole setup. I saw the buggy and all the parts at his house last night.

It is 110% one awesome setup that will make someone very happy...:nod:

thanks matt, pics up

added servos and motor for sale as well:)

Im sure im forgetting something..lol

The buggy will also come with stickman hump pack, a used set of panther k2 mountered. And the switch that is in it. (a new airtronics switch)

Remember all the hopups on it are new and it is OBO(reasonable)

would do buggy, parts,motor,servos for $525 shipped+fees OBO

possible trade for a serpent 811 in nice shape

pms responded too

goodnite bump

Happy Turkey Day to all:nod:

I want the custom body let me know a price.

pm'd you sickm

:tire: