Mugen MTX-4R..Will trade for 1/8 offroad set up
06-02-2009, 07:10 AM
#1
Tech Apprentice
Thread Starter
Mugen MTX-4R...Mint.
Adult owned and raced Mugen MTX-4, very well taken care of and maintained. Except for the steering uprights, it's basically now a MTX-4R because of all the little mods put on it. Lots of extra parts to make you ready to race.The original manual is included and some spreadsheets that i got online to help tune this car : gear ratio chart, overdrive ratio will also be included
It is on mounted with the low ratio side pulleys and runs like a dream, bearings are in excellent shape and gas tank is in perfect condition, the only part that hasnt been changed to bring it to a MTX-4R are the steering spindles.
Most of the following options were installed to bring it to a MTX-4R, the others stated are what i'm letting go with the chassis...
3Racing ventilated brake disk and yellow Teflon brake pads mounted. CVD’s all around (not the mugen dogbones), a li-po receiver battery, Hitec HS-425BB for throttle, new side belt bearings, new 2 speed clutch shoes, new rear belt installed, 30wt losi shock oil and violet springs all around, a pressure chamber installed for fuel
+
All the extra goodies go as follow.This will give you an idea of the value of this awesome package:..
. Spare tires NIB
· B-Tech 4mm chassis (already on car)
· 3 mm reg. Mugen chassis
· Front diff installed
· Extra complete rear diff ready to go
· One way for front included (complete with outdrives, just swap the main gear)
· Spur gears lot: 54t 58t 59t 60t plus 60t and 54t already on car
· Pinion gears lot:: 3x16t, 2x17t, 1x18t, 21t, 2x22t, 23t, 24t
· 3 clutch bells, : 1 light weight 3Racing, 2 regulars(one needs a little polishing on the contact surface)
· 2 motor backplates for clutch with nut so you can set up to different motors
· Grey, black and red clutch plates(one of each) with lightweight clutch shoes ( 2 complete sets)
· All the Mugen racing springs for front and rear
· 3Racing front CVD set for front (new in package)
· Mugen titanium steering and camber link rods (brand new in package)
+ other parts like extra belts, spacers, bulkheads, steering knuckles, arms, brake disk, all the servo blocks, spacers, extra body post front etc...
I also have a fesh piston and sleeve RB Rody tuned turbo engine(not quite broke in yet) Fast!!.Pics now posted below
I have no history here at Rctech but i have had many deals over the years on many other RC sites buying/selling and trading..All 100% positive transactions
.Send me your email and i will send you more pics and details..thank you..
It is on mounted with the low ratio side pulleys and runs like a dream, bearings are in excellent shape and gas tank is in perfect condition, the only part that hasnt been changed to bring it to a MTX-4R are the steering spindles.
Most of the following options were installed to bring it to a MTX-4R, the others stated are what i'm letting go with the chassis...
3Racing ventilated brake disk and yellow Teflon brake pads mounted. CVD’s all around (not the mugen dogbones), a li-po receiver battery, Hitec HS-425BB for throttle, new side belt bearings, new 2 speed clutch shoes, new rear belt installed, 30wt losi shock oil and violet springs all around, a pressure chamber installed for fuel
+
All the extra goodies go as follow.This will give you an idea of the value of this awesome package:..
. Spare tires NIB
· B-Tech 4mm chassis (already on car)
· 3 mm reg. Mugen chassis
· Front diff installed
· Extra complete rear diff ready to go
· One way for front included (complete with outdrives, just swap the main gear)
· Spur gears lot: 54t 58t 59t 60t plus 60t and 54t already on car
· Pinion gears lot:: 3x16t, 2x17t, 1x18t, 21t, 2x22t, 23t, 24t
· 3 clutch bells, : 1 light weight 3Racing, 2 regulars(one needs a little polishing on the contact surface)
· 2 motor backplates for clutch with nut so you can set up to different motors
· Grey, black and red clutch plates(one of each) with lightweight clutch shoes ( 2 complete sets)
· All the Mugen racing springs for front and rear
· 3Racing front CVD set for front (new in package)
· Mugen titanium steering and camber link rods (brand new in package)
+ other parts like extra belts, spacers, bulkheads, steering knuckles, arms, brake disk, all the servo blocks, spacers, extra body post front etc...
I also have a fesh piston and sleeve RB Rody tuned turbo engine(not quite broke in yet) Fast!!.Pics now posted below
I have no history here at Rctech but i have had many deals over the years on many other RC sites buying/selling and trading..All 100% positive transactions
.Send me your email and i will send you more pics and details..thank you..
Last edited by xv-townboy; 06-19-2009 at 04:20 PM. Reason: lower price
06-03-2009, 09:07 AM
#2
Tech Apprentice
Thread Starter
Baddabump...
Last edited by xv-townboy; 06-19-2009 at 04:21 PM.
06-04-2009, 08:32 AM
#3
Tech Apprentice
Thread Starter
Lets bring it back up
..Mint condition.
..Mint condition.
06-05-2009, 10:45 PM
#4
Tech Apprentice
Thread Starter
Who wants it
06-07-2009, 12:15 AM
#5
Tech Apprentice
Thread Starter
Bump it up....
Last edited by xv-townboy; 06-09-2009 at 02:20 AM.
06-09-2009, 02:20 AM
#6
Tech Apprentice
Thread Starter
A new day...
06-10-2009, 07:11 AM
#7
Tech Apprentice
Thread Starter
Dailly bump....Thank you
06-12-2009, 02:02 AM
#8
Tech Apprentice
Thread Starter
Lets get this sold!..New price!!
Lets get this sold...$500.00 plus shipping..
...$500.00 plus shipping..
Last edited by xv-townboy; 06-19-2009 at 04:21 PM.
06-13-2009, 03:20 AM
#9
Tech Apprentice
Thread Starter
Bump it
06-15-2009, 11:34 AM
#10
Tech Apprentice
Thread Starter
lowest price
Bump..
Last edited by xv-townboy; 06-17-2009 at 11:37 PM.
06-19-2009, 04:22 PM
#11
Tech Apprentice
Thread Starter
Somebody wants it
06-22-2009, 12:02 PM
#13
Tech Apprentice
Thread Starter
Send me some pics and details if you like...Still for sale
06-23-2009, 07:58 AM
#14
Tech Apprentice
Thread Starter
Baddabump....
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
