FS: The mother of them all, Mini-Z AWD package
#1
FS: The mother of them all, Mini-Z AWD package
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:16 AM.
#2
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:17 AM.
#3
Up for sale is my best Mini-Z AWD race car with all the left over mini-Z parts and accessories that I have left. I will be making this one package for the car and spare parts, and an add on package for the rest of the mini z accessories. Who ever buys this will be getting a great race proven wining car for more than half off what it would cost to build. All you will need is a controller with some crystals and you are good to go.
***AWD race car***
- The car started off as the full ball bearing version performance hard plastic chassis build it your self kit. I no longer have the factory Kyosho box for this.
- Atomic mods ceramic ball bearings for the center shaft, main diff bearings, and rear SAS suspension knuckles, Standard Kyosho ball bearings on the front knuckles
- Delrin steering gears
- Atomic mods 98mm extension kit
- Atomic mods black delrin 98mm spur gears
- Atomic mods SAS rear suspension kit
- Atomic mods 2 deg camber knuckles for SAS rear suspension
- Atomic mods 2 deg caster arms for SAS rear suspension
- NEW style Atomic mods aluminum rear SAS shocks
- Atomic mods blue, orange, and silver springs for SAS rear suspension
- Atomic mods plastic/delrin ball diffs front and rear, they have been re-built to my specs
- Lay down crystal adapter to fit any body
- Atomic mods aluminum heat sink and air scoop motor holder
- Atomic mods monster stock motor
- PN racing metal pinion gears
- PN racing aluminum motor holders with different sizes to allow you to run all sorts of gear ratios from A1/B1, A1.5/B1.5, to A3.5/B3.5 (more gear ratios than you would know what to do with)
- PN racing 1.5 Deg camber front knuckle
- Kyosho spring set for the suspension up front
- PN Racing orange shims for lowering
- Atomic mods Ti axle shafts
- Aluminum hex nuts all around
- Upgraded wire all around, Batt has been directly soldered to the board and the motor is running the same larger gauge wire.
- Atomic mods front white dish 3.5mm offset “narrow” wheels with stock kit rubber
- Atomic mods rear white dish 3.0mm offset “wide” wheels with stock kit rubber
*** Spare parts, extra tuning parts, parts for future re-builds, wheels/tires, etc. ***
- Lots of extra motor/battery connection wires, some stock some PN racing upgraded wire.
- Two stock kit motors
- 4 extra motor cans with end bells.
- 2 sets of extra PN racing brushes (for PN can)
- 3 extra motor resistors
- More stock screws, washers, etc than you can shake a stick at
- Two stock never used diffs
- PN racing shim set 0.1, 0.2, and 0.3mm shims
- Extra diff gears for future re-builds
- Every spur gear for all size widths
- Atomic mods re-build kit for Ti-universal shafts
- 4 pairs of stock AWD “wide” mesh wheels in every offset they offer
- 7 pairs of stock AWD “narrow” mesh wheels in every offset they offer (with a couple duplicates)
- 7 pairs of “narrow” tires ranging from PN racing 20deg to stock kit tires.
- 4 pairs of “wide” tires ranging from PN racing treaded to stock kit tires.
- Two plastic Mini-Z car stands.
- White Enzo body with wing
- Red Enzo body with holes drilled to clear the front suspension
- White Ford GT-40 body with holes drilled to clear the front suspension
- Malaren GT body with holes drilled to clear the front suspension
- Core transponder
*** Non Chassis parts that can be added to the package ***
- PN racing bearing cleaning case
- PN racing wide tire tape roll
- PN racing AAA charge holder
- 33 Duracell rechargeable 1000mAh Ni-Mh cells
- Tamiya Mini Speed Checker dyno
Here are pictures of the car and all the parts:
http://www.osbornhouse.com/rc/miniz/awd/
When you add up all the parts and accessories the total comes to well over $800.00.
As for my price; For the car and all its spare/tuning parts I am asking $300.00 shipped OBO, and if you want the non chassis parts as part of the package I am asking $330.00 shipped OBO.
If you have any questions or would like to throw me an offer please send me a PM or an e-mail. Please, please no low balers. This package is worth a LOT of money and I am selling it at a GREAT value.
- Dana
[email protected]
***AWD race car***
- The car started off as the full ball bearing version performance hard plastic chassis build it your self kit. I no longer have the factory Kyosho box for this.
- Atomic mods ceramic ball bearings for the center shaft, main diff bearings, and rear SAS suspension knuckles, Standard Kyosho ball bearings on the front knuckles
- Delrin steering gears
- Atomic mods 98mm extension kit
- Atomic mods black delrin 98mm spur gears
- Atomic mods SAS rear suspension kit
- Atomic mods 2 deg camber knuckles for SAS rear suspension
- Atomic mods 2 deg caster arms for SAS rear suspension
- NEW style Atomic mods aluminum rear SAS shocks
- Atomic mods blue, orange, and silver springs for SAS rear suspension
- Atomic mods plastic/delrin ball diffs front and rear, they have been re-built to my specs
- Lay down crystal adapter to fit any body
- Atomic mods aluminum heat sink and air scoop motor holder
- Atomic mods monster stock motor
- PN racing metal pinion gears
- PN racing aluminum motor holders with different sizes to allow you to run all sorts of gear ratios from A1/B1, A1.5/B1.5, to A3.5/B3.5 (more gear ratios than you would know what to do with)
- PN racing 1.5 Deg camber front knuckle
- Kyosho spring set for the suspension up front
- PN Racing orange shims for lowering
- Atomic mods Ti axle shafts
- Aluminum hex nuts all around
- Upgraded wire all around, Batt has been directly soldered to the board and the motor is running the same larger gauge wire.
- Atomic mods front white dish 3.5mm offset “narrow” wheels with stock kit rubber
- Atomic mods rear white dish 3.0mm offset “wide” wheels with stock kit rubber
*** Spare parts, extra tuning parts, parts for future re-builds, wheels/tires, etc. ***
- Lots of extra motor/battery connection wires, some stock some PN racing upgraded wire.
- Two stock kit motors
- 4 extra motor cans with end bells.
- 2 sets of extra PN racing brushes (for PN can)
- 3 extra motor resistors
- More stock screws, washers, etc than you can shake a stick at
- Two stock never used diffs
- PN racing shim set 0.1, 0.2, and 0.3mm shims
- Extra diff gears for future re-builds
- Every spur gear for all size widths
- Atomic mods re-build kit for Ti-universal shafts
- 4 pairs of stock AWD “wide” mesh wheels in every offset they offer
- 7 pairs of stock AWD “narrow” mesh wheels in every offset they offer (with a couple duplicates)
- 7 pairs of “narrow” tires ranging from PN racing 20deg to stock kit tires.
- 4 pairs of “wide” tires ranging from PN racing treaded to stock kit tires.
- Two plastic Mini-Z car stands.
- White Enzo body with wing
- Red Enzo body with holes drilled to clear the front suspension
- White Ford GT-40 body with holes drilled to clear the front suspension
- Malaren GT body with holes drilled to clear the front suspension
- Core transponder
*** Non Chassis parts that can be added to the package ***
- PN racing bearing cleaning case
- PN racing wide tire tape roll
- PN racing AAA charge holder
- 33 Duracell rechargeable 1000mAh Ni-Mh cells
- Tamiya Mini Speed Checker dyno
Here are pictures of the car and all the parts:
http://www.osbornhouse.com/rc/miniz/awd/
When you add up all the parts and accessories the total comes to well over $800.00.
As for my price; For the car and all its spare/tuning parts I am asking $300.00 shipped OBO, and if you want the non chassis parts as part of the package I am asking $330.00 shipped OBO.
If you have any questions or would like to throw me an offer please send me a PM or an e-mail. Please, please no low balers. This package is worth a LOT of money and I am selling it at a GREAT value.
- Dana
[email protected]
I might be interested in your stuffs but may i know where is your location? By the way i am located in Malaysia.
Is the item in very good running condition?
#4
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:17 AM.
#6
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:17 AM.
#7
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:17 AM.
#8
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:18 AM.
#9
#10
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:18 AM.
#11
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:18 AM.
#12
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:18 AM.
#13
Tech Fanatic
iTrader: (19)
$$$$$$$
Thanks for the kind words.
Sorry bro I was hoping I did not have to sell this but I have bills to pay so I can send my wife to the culinary institute to become a pastry chef. HOLY S%&T these schools are expensive. So its looking like I have to sell most of my RC stuff to make it happen.
Sorry bro I was hoping I did not have to sell this but I have bills to pay so I can send my wife to the culinary institute to become a pastry chef. HOLY S%&T these schools are expensive. So its looking like I have to sell most of my RC stuff to make it happen.
I SENT MY DAUGHTER TO THE CALIFORNIA CULINARY ACADEMY IN
SAN FRANCISCO ON POLK ST.
BUT ATLEAST NOW SHE IS A PASTRY CHEF AND DOING WELL.
IT WAS ALL WORTH IT WHEN IT WAS ALL SAID AND DONE.
nEIL
#14
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:19 AM.
#15
SOLD
Last edited by Rotary Racer; 11-17-2007 at 10:19 AM.