![]() |
Re: OS TR12 Efra version
Originally posted by danjoy25 Is the TR with the stainless steel heat sink quicker that the normally blue ones? Is it worth the $25.00 extra? Bottom line about engine break-in guys. I posted on this many pages back- you can search for the details, but a fresh engine DOES NOT need tank after tank of idle speed with a rich setting!! All you have to do is run the motor conservatively on the tune around the track the same way you would race- part throttle, sometimes WOT, etc. Just don't run but 2-4 minutes at a time. Let the motor cool then run it again. After 3-4 heat cycles start sneaking up on a good tune and roll. HEAR this- idling these motors super rich over and over and over is killing the piston to cylinder wall seal!!! You are washing the freaking cylinder wall down with super rich settings!! |
OS 12 R-Spec and E-Spec
Hey guys someone told me that the OS 12TR E Spec and R Spec have the same case as the 12TR (P) T????? Please give me your opinion so i cna prove him wrong :)
|
Re: Re: OS TR12 Efra version
Originally posted by BigDogRacing You mean the E-spec? YES it is considerably faster, even more so than OS claims. Fast enough your lap times will probably decrease!! LOL J/K. But very serious about the power. Bottom line about engine break-in guys. I posted on this many pages back- you can search for the details, but a fresh engine DOES NOT need tank after tank of idle speed with a rich setting!! All you have to do is run the motor conservatively on the tune around the track the same way you would race- part throttle, sometimes WOT, etc. Just don't run but 2-4 minutes at a time. Let the motor cool then run it again. After 3-4 heat cycles start sneaking up on a good tune and roll. HEAR this- idling these motors super rich over and over and over is killing the piston to cylinder wall seal!!! You are washing the freaking cylinder wall down with super rich settings!! |
Re: OS 12 R-Spec and E-Spec
Originally posted by FUK_WRX Hey guys someone told me that the OS 12TR E Spec and R Spec have the same case as the 12TR (P) T????? Please give me your opinion so i cna prove him wrong :) |
Re: OS TR12 Efra version
Originally posted by danjoy25 Is the TR with the stainless steel heat sink quicker that the normally blue ones? Is it worth the $25.00 extra? |
O.S. .12 TR (P)-T R-Spec
I think danjoy means this engine. O.S. .12 TR (P)-T R-Spec
http://www2.gpmd.com/image/o/osmg2007.jpg |
Re: Re: OS 12 R-Spec and E-Spec
Originally posted by 3434 Hope you didn't bet on it. OS part# 21451010 is the crankcase for all three. I wonder if the E/R-Spec is as fast or faster than the (P) T :D :nod: there so hard to bloody find any suggested shops etc.. |
Kondo Customs
Hi
Has anyone tried the KONDO custom TR - T engines (Modded OS TR T) or the Piston /Sleeve sets along with the modded crankshafts....... ?? This upgrade costs around 160$ if yess, does it really give it more power!! only the person who has burnt some rubber with this or seen one should know ? ZiiZO |
Originally posted by rcabj :D ;) pics 2 |
Re: Re: OS TR12 Efra version
Originally posted by 3434 I don't know of any OS engine with a stainless steel heat sink. Check out the link |
Originally posted by uaerc got the same pipe ?? so how does it perform with tr |
Re: Re: Re: OS TR12 Efra version
Originally posted by danjoy25 http://rc-mushroom.com/product_info.php?cPath=169&products_id=4449 Check out the link http://rc-mushroom.com/product_info....oducts_id=4449 |
I spoke to an OS engine rep about pipe choices on the .12 TR. he recomended trying the os 1040 pipe with the 1000m manifold. I havent got around to it yet but worth a try to anyone looking for a good pipe combo.
|
Originally posted by rcosmax I spoke to an OS engine rep about pipe choices on the .12 TR. he recomended trying the os 1040 pipe with the 1000m manifold. I havent got around to it yet but worth a try to anyone looking for a good pipe combo. http://www.skylinercracing.com/store/c_19.htm |
Re: Re: Re: OS TR12 Efra version
1 Attachment(s)
Originally posted by danjoy25 http://rc-mushroom.com/product_info....oducts_id=4449 Check out the link Do you mean this one? Its aluminum. A stainless steel one would be rather heavy. |
| All times are GMT -7. It is currently 07:37 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.