Originally Posted by FREELANCE_RCer
(Post 4341691)
http://www.redrc.net/wp-content/uplo...revcrf21-2.jpghttp://www.redrc.net/wp-content/uplo...revcrf21-3.jpg
Looks like PICCO took the .21 size engine production from Japanese manufacturers. These seen @ redrc.net website for off-road use. The wait will still be a little longer for on-road for sure.:tire: |
I have an Orion CRF .12 motor. My issue is that it stutters on the low end. If I initially give it full throttle at the beginning of the power curve, it " stutters " on the low end until it clears out and is normal on the mid / high rpm range. I've tried adjusting the needles and it still does it. Any ideas on what's happening ? Thanks in advance.
|
hi guys.i know that this is an old thread but i want to make a question!
i am going to replace the crank in my crf.i can find 5.5mm-6mm-6.5mm diameter crank for a good price.does any one know which is better?with the big crank timing that this engine has in mind. have anyone try 5.5 or 6.5crank? any help will be appreciated! |
Originally Posted by GREGORY!
(Post 5337532)
hi guys.i know that this is an old thread but i want to make a question!
i am going to replace the crank in my crf.i can find 5.5mm-6mm-6.5mm diameter crank for a good price.does any one know which is better?with the big crank timing that this engine has in mind. have anyone try 5.5 or 6.5crank? any help will be appreciated! no one have an answer?? nano?do you know the answer? thanks! |
Originally Posted by GREGORY!
(Post 5347920)
no one have an answer??
nano?do you know the answer? thanks! |
Originally Posted by Nano
(Post 5375753)
With the CRF technology, bigger bore cranks do not give straight results like with standard engines. I would tell you to keep the original crank.
thank you nano! for one more time you help us! very nice! by the way you have a pm. |
settings
was wondering if anyone could tell me the factory settings for the crf 21.not the new one
|
sorry I commented something that was a year old posting
|
hi.
does anyone have try the new clutch from orion for the rrr?#ori88691 does it use the #ORI88637 flywheel? can i buy the bell only? does it has the same clutch parts with the crf clutch that was coming with the crf engine set? thanks! |
I have a question
This dynamometro I it can buy in some place¿? In case of being able to buy it to that I coast¿? If I cannot buy it I can obtain the planes of dyno¿? |
i try to find i direct pin clip for this engine.i can't find any.i have try novarossi,and grp but they are not the same.this engine need a thinner clip.can someone say if the sirio clips can be used?
thanks in advice! |
Hi,
I'm getting the Kyosho X312T version of this engine soon. Will be running 16% nitro fuel and looking at using the no.6 orion glow plugs. What is the head clearence of this engine from factory and what head clearence should I use with 16% nitro fuel? I'm thinking the head clearence to use is 0.1mm? |
yes.0.1mm.
|
Is it me or have the parts supply for the CRF Wasp .12 completely dried up.
Since the wasp .12 is no longer available, can anyone confirm if the Alpha .12 parts will work? |
Raman Try bartz parts or barts partz ;)
I bought a cranck not so long time ago.. good service |
All times are GMT -7. It is currently 09:59 AM. |
Powered By: vBulletin v3.9.3.8
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.