349LikesNOVAROSSI Engine thread....
03-23-2016, 08:35 PM
#8851
Pretty much just a decoration. Almost everyone just leaves it at the stock flush setting. But if you were to mess with it the midrange adjustment basically adjusts the position of the spray bar... but any gains are usually minimal and not worth the hassle.
03-24-2016, 05:22 AM
#8852
I agreed with it. Is really decoration unless you over tune it will make the engine stupid
03-24-2016, 05:39 AM
#8853
it allows you to move the fuel outlet to match the size of the venturi insert...use a small insert you move it inwards, use a large insert you move it outwards...Basically allowing you to maintain the same location in relation to the incoming air stream...... when you adjust it you also adjust the LSN with it...so if you turn the Mid out half a turn you would turn the LSN in 1/2 a turn.....
03-25-2016, 12:30 PM
#8855
Elite 5
Ok guys,will a Werks 2058 be a descent pipe?I also have a ninja pipe 2042(suppose to be the same As a os 2060)got one of these elites on the way and trying to formult a plan.$s$ for a pipe.
Last edited by smash8ight; 03-25-2016 at 05:13 PM.
03-25-2016, 01:08 PM
#8856
What's the current Nova Direct coupon code? Thanks...
03-25-2016, 02:05 PM
#8857
well that gold edition nova 3 port absolute is selling is a pretty decent little motor for the price, the specs they list are wrong as its a square stroke motor but with 1.0s and std ae rc8 shoes its got decent bottom and enough top end for at least 100 foot straight and its just broken in.
running a werks 086 on it with an unknown smooth bend header(its my shortest smoothie) in an ancient cl-1buggy
https://youtu.be/9k9YKgPgthM
running a werks 086 on it with an unknown smooth bend header(its my shortest smoothie) in an ancient cl-1buggy
https://youtu.be/9k9YKgPgthM
Last edited by HaulinBass; 03-25-2016 at 07:29 PM.
03-25-2016, 05:48 PM
#8858
I'm looking for some options for a throttle return spring set up. I'm told a rubber band works or a spring. I'm also told this only pulls on one side of the carb so it causes uneven wear on the slide which effects tune. What are some options for this? Pics are helpful if possible.
03-25-2016, 06:31 PM
#8859
I'm looking for some options for a throttle return spring set up. I'm told a rubber band works or a spring. I'm also told this only pulls on one side of the carb so it causes uneven wear on the slide which effects tune. What are some options for this? Pics are helpful if possible.
Rubber bands, water balloons, silicon hair bands, springs... It really doesn't matter as they all do the same thing. As long as it closes the carb all the way to the idle stop, it doesn't matter.
I have never run without one honestly and I think it helps to "assist" the engine coming from WOT to idle...But as long as it closes smoothly, you should be fine.
03-25-2016, 08:55 PM
#8860
They can cause the carb to bind. I use a hair band and it is light enough to close the carb but not cause the carb to bind. Never ran one for 10 plus years.
03-25-2016, 11:35 PM
#8861
Search "Carb-O's" at Amain..
03-26-2016, 06:45 AM
#8863
Cant honestly say ive Ever had my throttle linkage ball pop off, Also a proper build linkage will technically never fall apart (vehicle to vehicle accidents aside)
So therefor i dont see the point of a Goody band anymore.
So therefor i dont see the point of a Goody band anymore.
03-26-2016, 07:14 AM
#8864
I'm looking for some options for a throttle return spring set up. I'm told a rubber band works or a spring. I'm also told this only pulls on one side of the carb so it causes uneven wear on the slide which effects tune. What are some options for this? Pics are helpful if possible.
http://novarossidirect.com/THROTTLE-...NG_p_3383.html