Pattojnr

iTrader: (19)

im hoping your continuence with TM stays strong. i do understand the efforts undertaken by you to battle through sorting out issues. i had a bad run for a while with the car, then it all seemed to come good for the states. pitty about some tyre choices for the nats, be good to see you in the A final with the TM.

aussies1129

iTrader: (74)

let the good times roll!!!

NitroWD

iTrader: (5)

this is what i call: DIE_HARD G4 SUPPORT!!!

That's the attitude man! yeah...

freestyles

iTrader: (14)

Why do you run a fuel filter on your pressure line? An old kit i had said to do this to but i never understood why.

P.S: They look fast just sitting there

ALG

they use the filter as a pressure chamber and to lean the middle range of the engines.

the best way ti know if it works is to try it. remember to take out the filter element

have fun
ALG

aussies1129

iTrader: (74)

yes these are mugen pressure chambers which are very inexpensive they help maintain constant pressure to the tank I have had them on the car for a while now and have worked well so far.
and yes my number one car just got a new picco edo tuned engine and a few weeks back during an intercity meet between townsville and Cairns I got the setup right and the right mindset which enabled me to smash the track lap record at our local track thats against RRR and MTX running modded nova353s . but due to a wire coming out onto the track (myfault) I missed out on any podium finish
cheers

NitroWD

iTrader: (5)

great job but a pity...

let me guess: yr no.1 car is the one on the left in yr pic? the obe with the WC frt...

aussies1129

iTrader: (74)

yes thats the one good guess, I have not gone the wc rear and chassis yet as I fear this may make the car to stiff and there fore messing with the cars rear traction lets see?
also did anyone else find that the front wc setup looks a little out of alignment especially on the left side?maybe my left bulkhead has taken a hit?
cheers

freestyles

iTrader: (14)

Spewin mate, but that's racing i suppose and that's why we keep coming back for more

How strong are those alloy bulkheads? I'm worried that if i had them i would bend/break them

freestyles

iTrader: (14)

Could someone please tell me what those round inserts are for in the front and rear flash pit hubs (non quick change). Thanks

viperbill1963

ok i just bought a mongoose g4 evo from rd logics and i would appreciate any info and or tips on getting this car up and running any set ups and tips to improve the car i am planning to run a sirio .12 motor which tune pipe would you suggest i use thanks and hope to run nitro on road in the bass pro series race in november

Sp Racer

iTrader: (12)

The inserts are there to allow you to use the non quick change outer bearing - the quick change system uses the same size inner & outer bearing.

If you wanted to switch to the quick change system, you'd just do away with the insert...

aussies1129

iTrader: (74)

dont even bother the kfactory quick change tyres they are very costly!! and I remember reading somewhere something about being illegal??not sure how true that is?
cheers

Pattojnr

iTrader: (19)

if you look at the rules for 200mm ic in the aarcmcc site, it clearly states no use of quick change wheel systems like 1/8th cars. this is for sanctioned events, so state titles, and national titles, there not legal.

Nitro-Racer*

hey hello everyone good to be back!! great news here from cyprus finished 1st in group B after racing in wet conditions for 25 minutes, the car was great!!! i am back on track with the championship. felling blue when hearing that people have issues with the tm cars, i have never broke any plastic part, just replaced them because it was time to, the only downside is the gears, you never know when they will strip off . anyway does anyone have any idea how i can reduce some weight, my car weight a ton after installing the 4mm chassi and the nova air cooler....
thanks..