Mugen MTX-3
#5221
Originally posted by RClover
ok, how about 16/21 47/43? when to use this?
ok, how about 16/21 47/43? when to use this?
#5222
so we always try to even up both the tooth spread?
how long is your stra8?
how long is your stra8?
#5223
Originally posted by eddiethefish
If you ever wish to discard anything, spare the poor fish, send'em over to me, p... lease...
Where can I find the enneti clutch?
So now we have:
Black
Gray
Red
and enneti Yellow
I'm a hetero, but wonder if there'll be a rainbow one in the near future.
If you ever wish to discard anything, spare the poor fish, send'em over to me, p... lease...
Where can I find the enneti clutch?
So now we have:
Black
Gray
Red
and enneti Yellow
I'm a hetero, but wonder if there'll be a rainbow one in the near future.
So from harder to softer will be:
- Delta Red shoe Probably Kyosho Red shoe is the same rebadged...
- Enneti black
- Mugen black
- Enneti yellow
- Mugen Gray
Ended using the Enneti black and the Enneti yellow, have here some Delta Red shoes, but found too hard for the MTX3 (but on the MRX3 I have one of those with good results). Main advantage from the Mugen is they don't glaze up.
#5224
Originally posted by RClover
Corse-R, no sign of PM from you about the 363mm belts? dont leave me alone...i'm lonely
Corse-R, no sign of PM from you about the 363mm belts? dont leave me alone...i'm lonely
YHPM (You Have Private Mail).
#5225
Originally posted by Corse-R
There's another black shoe from enneti, quite similar to the Picco shoes, slightly harder.
So from harder to softer will be:
- Delta Red shoe Probably Kyosho Red shoe is the same rebadged...
- Enneti black
- Mugen black
- Enneti yellow
- Mugen Gray
Ended using the Enneti black and the Enneti yellow, have here some Delta Red shoes, but found too hard for the MTX3 (but on the MRX3 I have one of those with good results). Main advantage from the Mugen is they don't glaze up.
There's another black shoe from enneti, quite similar to the Picco shoes, slightly harder.
So from harder to softer will be:
- Delta Red shoe Probably Kyosho Red shoe is the same rebadged...
- Enneti black
- Mugen black
- Enneti yellow
- Mugen Gray
Ended using the Enneti black and the Enneti yellow, have here some Delta Red shoes, but found too hard for the MTX3 (but on the MRX3 I have one of those with good results). Main advantage from the Mugen is they don't glaze up.
Thought Delta Red should be the softest. Correct me, will you?
#5226
Originally posted by RClover
so we always try to even up both the tooth spread?
how long is your stra8?
so we always try to even up both the tooth spread?
how long is your stra8?
#5227
Originally posted by Manticore
i have no actually figure about the back straight length but the stock gearing of MTX3 works very well there but i use 42 on the second spur
i have no actually figure about the back straight length but the stock gearing of MTX3 works very well there but i use 42 on the second spur
#5228
Originally posted by RClover
you know..MY FRIEND told me there are many many types of scratches...deep scratch, mild scratch...etc..etc..
you know..MY FRIEND told me there are many many types of scratches...deep scratch, mild scratch...etc..etc..
#5229
Gear Ratio Calculation on 0.8mm
Hello,
Since Mugen will be launching its new gearing 0.8mm, how do I calculate the gear ratio now. I wanna be able to compare these 0.8 to the 1.0 ones.
Thank you,
eddie
Since Mugen will be launching its new gearing 0.8mm, how do I calculate the gear ratio now. I wanna be able to compare these 0.8 to the 1.0 ones.
Thank you,
eddie
#5230
Originally posted by Corse-R
Severe scratches caused by going upside down by the backstraight at full throttle (ouch)
Severe scratches caused by going upside down by the backstraight at full throttle (ouch)
#5231
Originally posted by eddiethefish
Hello Corse-R,
Thought Delta Red should be the softest. Correct me, will you?
Hello Corse-R,
Thought Delta Red should be the softest. Correct me, will you?
#5233
Originally posted by Corse-R
Severe scratches caused by going upside down by the backstraight at full throttle (ouch)
Severe scratches caused by going upside down by the backstraight at full throttle (ouch)
#5234
Re: Gear Ratio Calculation on 0.8mm
Originally posted by eddiethefish
Hello,
Since Mugen will be launching its new gearing 0.8mm, how do I calculate the gear ratio now. I wanna be able to compare these 0.8 to the 1.0 ones.
Thank you,
eddie
Hello,
Since Mugen will be launching its new gearing 0.8mm, how do I calculate the gear ratio now. I wanna be able to compare these 0.8 to the 1.0 ones.
Thank you,
eddie
While on the second is: 4.823
I'd just like to find out the config on 0.8 ones that will yield a close result.