Mugen MTX-4
#8596
#8597
Don't fight over 24T vs 25T ...........
I'm using 25T and 21T brake pulley !!!
I'm using 25T and 21T brake pulley !!!
#8598
#8599
Tech Fanatic
iTrader: (11)
Ok, got a few questions
1. What is the performance different between all the pulleys.
2. How do you go about replacing the tank and a rear belt (dont wanna more than needed)
3. What are some makeshift things I can use for checking my chassis setup .etc?
4. And what are "Active Speed" foams like?
Thanks,
LogiK
1. What is the performance different between all the pulleys.
2. How do you go about replacing the tank and a rear belt (dont wanna more than needed)
3. What are some makeshift things I can use for checking my chassis setup .etc?
4. And what are "Active Speed" foams like?
Thanks,
LogiK
#8600
Tech Fanatic
iTrader: (45)
Has anyone on here tried using the front diff. setup that came with the car? I went and got all the extra parts needed to put it together like the manual stated...but in doing so...it doesnt seem to fit.
#1. It seems it is too wide..and the bearing/hub rubs on each side.
#2. The steering rack hits the diff. case.
Please tell me there is something I am missing here...as I have looked over the manual a dozen times.
Thanks
Derek
#1. It seems it is too wide..and the bearing/hub rubs on each side.
#2. The steering rack hits the diff. case.
Please tell me there is something I am missing here...as I have looked over the manual a dozen times.
Thanks
Derek
#8601
Has anyone on here tried using the front diff. setup that came with the car? I went and got all the extra parts needed to put it together like the manual stated...but in doing so...it doesnt seem to fit.
#1. It seems it is too wide..and the bearing/hub rubs on each side.
#2. The steering rack hits the diff. case.
Please tell me there is something I am missing here...as I have looked over the manual a dozen times.
Thanks
Derek
#1. It seems it is too wide..and the bearing/hub rubs on each side.
#2. The steering rack hits the diff. case.
Please tell me there is something I am missing here...as I have looked over the manual a dozen times.
Thanks
Derek
Front: T0202 Diff Cup Joint
Rear: T0261 Diff Cup Joint
Also what Ackermann insert/position are you using?
#8602
Has anyone on here tried using the front diff. setup that came with the car? I went and got all the extra parts needed to put it together like the manual stated...but in doing so...it doesnt seem to fit.
#1. It seems it is too wide..and the bearing/hub rubs on each side.
#2. The steering rack hits the diff. case.
Please tell me there is something I am missing here...as I have looked over the manual a dozen times.
Thanks
Derek
#1. It seems it is too wide..and the bearing/hub rubs on each side.
#2. The steering rack hits the diff. case.
Please tell me there is something I am missing here...as I have looked over the manual a dozen times.
Thanks
Derek
I think the problem is with the diff pulley....if you are using one way...there is a plastic piece which you need to glue it to the pulley but you can't glue it if you are using the diff or spool.....if anyone got an exploded diagram....it is easier to pin point the part.....
#8603
i just made up a front diff but have not put it in yet
but i did last year made a spool and did the mistake of putting on the ring on the pulley
but i did last year made a spool and did the mistake of putting on the ring on the pulley
#8604
I think the problem is with the diff pulley....if you are using one way...there is a plastic piece which you need to glue it to the pulley but you can't glue it if you are using the diff or spool.....if anyone got an exploded diagram....it is easier to pin point the part.....
#8608
how many diff gasket are you using????did you put too much sillicone glue or something???or maybe make sure that the bearing goes all the way in on the diff case.....
#8609
in any case how does it translate to driving feels???