Xray RX8 1/8th Scale
#916
Tech Elite
iTrader: (29)
ok, im definitively ordering some acorn gear, nice looking stuff...ok here might be a noob sound question, but i am interested in those aluminum front anti roll bar holder as well as others but i have a question with that...when setting up the front droop i obviously take shocks off and slide bars out,problem i always have is when i slide the bars back in, seems to throw one arm off, or both, so i use that adjusting tab on left side to gget close but never does the trick, do i use tab and mess with droop screws again, or are my anti roll bars outta wack, and that's where the aluminum ones would be better? sorry for the rant, just a setup issue i was having...thanks
#917
Tech Master
iTrader: (1)
Hello Tommy, I dont think it is your bars being out of wack, I would still use the side adjuster on the holder to take that little un-balanced out of the bars that works best for me. I would set the droop equally and then make sure that your bars are measured in the center of the bulkhead or swaybar holders and not in to deep. Try that if you havnt, I am sure you have already, just my2cents.
#919
Tech Elite
iTrader: (29)
thanks you were right :^)....
just outta curiosity, how much do you think the 2012 upgrade kit will be,i have just a race on my rx89 etc etc..i will sell if i have to no prob, seems the a arms front cannot be used, new chassis and top plate , etc etc...i have plans to buy new kit, actually im going to list my rx8 tonight, with very little use and spares for cheap just to move it.....
just outta curiosity, how much do you think the 2012 upgrade kit will be,i have just a race on my rx89 etc etc..i will sell if i have to no prob, seems the a arms front cannot be used, new chassis and top plate , etc etc...i have plans to buy new kit, actually im going to list my rx8 tonight, with very little use and spares for cheap just to move it.....
#920
Tech Master
iTrader: (1)
If your not a Drew story, you havn't gone out with him.
#922
Tech Master
iTrader: (9)
YES, I'm gold now, lol. I am excited for the new year to join forces with all my friends again.. Naturally that not going to help my driving, so I guess I can be a Drew story for 2012. Stay tuned, Drew will have a lot to talk about and make fun of me, lol.
If your not a Drew story, you havn't gone out with him.
If your not a Drew story, you havn't gone out with him.
Jeff
#923
this calls for a new dance see you soon
#924
Tech Elite
iTrader: (29)
ok so im selling her...just not enough time, going to concentrate on buggy, xb9 i didnt leave the family
http://www.rctech.net/forum/r-c-item...m-edition.html
http://www.rctech.net/forum/r-c-item...m-edition.html
#925
Tech Master
iTrader: (1)
ok so im selling her...just not enough time, going to concentrate on buggy, xb9 i didnt leave the family
http://www.rctech.net/forum/r-c-item...m-edition.html
http://www.rctech.net/forum/r-c-item...m-edition.html
#926
Tech Master
iTrader: (1)
I would like to thank everybody for your support the A+ Products are going well and moving fast. Hope to aee you all at the next major race wearing my new red shirt and the NT1 and RX8. The site is starting to look good and all pictures are up.
Thanks Billy
www.acornracingusa.com
Thanks Billy
www.acornracingusa.com
#927
Tech Elite
iTrader: (184)
I would like to thank everybody for your support the A+ Products are going well and moving fast. Hope to aee you all at the next major race wearing my new red shirt and the NT1 and RX8. The site is starting to look good and all pictures are up.
Thanks Billy
www.acornracingusa.com
Thanks Billy
www.acornracingusa.com
#929
i will be looking for these parts also fully loaded