How to connect an AMB transponder?
#1
Tech Apprentice
Thread Starter
How to connect an AMB transponder?
Hi guys,
a friend of mine gave me a little red AMB transponder, but the connector are not on it (he had to cut and I have just 2 wires hanging out now). I wonder where I can hook it up?
Thanks in advance!
a friend of mine gave me a little red AMB transponder, but the connector are not on it (he had to cut and I have just 2 wires hanging out now). I wonder where I can hook it up?
Thanks in advance!
#2
You may have to do a little soldering.
Your best bet is to splice into the throttle servo wire.
You know, red to red and black to black.
Your friend should have told you this too.
Your best bet is to splice into the throttle servo wire.
You know, red to red and black to black.
Your friend should have told you this too.
#3
Otherwise you can use a servo connector and plug it into a spare channel on your receiver. This is they way it would come brand new - with the servo connector. I still have the instruction sheet for mine. I will try to post it here.
#4
Tech Apprentice
Thread Starter
Do you know if I can buy a Y connector that would split a unique connection in 2 connectors?
That would do a cleaner job.
If not, I will go in soldering. I have no problem with that. I was just wondering where to connect it to not affect any servos.
I already have a fail safe on the throttle link. Do you think that it will affect it?
That would do a cleaner job.
If not, I will go in soldering. I have no problem with that. I was just wondering where to connect it to not affect any servos.
I already have a fail safe on the throttle link. Do you think that it will affect it?
#5
Tech Apprentice
Thread Starter
Originally posted by j240z
Otherwise you can use a servo connector and plug it into a spare channel on your receiver. This is they way it would come brand new - with the servo connector. I still have the instruction sheet for mine. I will try to post it here.
Otherwise you can use a servo connector and plug it into a spare channel on your receiver. This is they way it would come brand new - with the servo connector. I still have the instruction sheet for mine. I will try to post it here.
That make sense! Do you know if there is always juice on the third channel plug!?
#6
Oh, I didn't know you had a third channel.
That would be better than putting three devices on one channel.
Just solder on another plug and plug it in. Third channel should be "hot".
I only have two channels on my receiver and I have a fail safe on the throttle. but I spliced into the steering servo for the transponder. Everything works great though.
That would be better than putting three devices on one channel.
Just solder on another plug and plug it in. Third channel should be "hot".
I only have two channels on my receiver and I have a fail safe on the throttle. but I spliced into the steering servo for the transponder. Everything works great though.
#7
Tech Apprentice
Thread Starter
Originally posted by Aggdaddy
Oh, I didn't know you had a third channel.
That would be better than putting three devices on one channel.
Just solder on another plug and plug it in. Third channel should be "hot".
I only have two channels on my receiver and I have a fail safe on the throttle. but I spliced into the steering servo for the transponder. Everything works great though.
Oh, I didn't know you had a third channel.
That would be better than putting three devices on one channel.
Just solder on another plug and plug it in. Third channel should be "hot".
I only have two channels on my receiver and I have a fail safe on the throttle. but I spliced into the steering servo for the transponder. Everything works great though.
#8
Well the transponder just needs power, and there's no way to turn off a particular channel on the receiver. So I'm pretty sure that it'll be on.
When you apply power to the receiver, everything is on. Your transmitter just sends a signal.
When you apply power to the receiver, everything is on. Your transmitter just sends a signal.
#9
Tech Apprentice
Thread Starter
Originally posted by Aggdaddy
Well the transponder just needs power, and there's no way to turn off a particular channel on the receiver. So I'm pretty sure that it'll be on.
When you apply power to the receiver, everything is on. Your transmitter just sends a signal.
Well the transponder just needs power, and there's no way to turn off a particular channel on the receiver. So I'm pretty sure that it'll be on.
When you apply power to the receiver, everything is on. Your transmitter just sends a signal.
I'll try it for sure (wonder how I will know if the transponder in on a home though) and confirm later.
Thanks again guys!
#10
Tech Adept
If it is the small amb red transponder, it will have a small led yellowish light on top when the power is supplied to it properly.
#11
YES! if your receiver has power it will power all the channels! And as sook said the yellow led on the transponder will be on!
#12
Or it will light up green if it's the older version.
#13
Tech Apprentice
Thread Starter
A little solder and it works in the 3rd plug guys!
Thanks a lot...
Thanks a lot...