Go Back  R/C Tech Forums > General Forums > Nitro On-Road
1/8th Nitro On-Road - Edam Razor > 1/8th Nitro On-Road - Edam Razor

1/8th Nitro On-Road - Edam Razor

Reply

Old 07-06-2014, 07:43 PM
  #271  
Tech Master
iTrader: (23)
 
TeamCarnage's Avatar
 
Join Date: Aug 2004
Location: Highland In. USA
Posts: 1,680
Trader Rating: 23 (100%+)
Default

Originally Posted by azeroth View Post
is there anybody elses front bumper that fits this chassis i really hate that they end up sagged down and goodbye steering towards the end of a run
Do the turnbuckle mod...
TeamCarnage is offline  
Reply With Quote
Old 07-07-2014, 10:50 AM
  #272  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,092
Trader Rating: 21 (100%+)
Default

have another thought on it
azeroth is offline  
Reply With Quote
Old 07-07-2014, 03:29 PM
  #273  
Tech Apprentice
 
Leichtmetall's Avatar
 
Join Date: Aug 2009
Location: Bavaria, Germany
Posts: 82
Default

When i had this Problem sometimes with an older Frontbumper, i made following:
I take three tires on table, puting car on it. one tyre under the rearend of chasis, and even one under the left and right end of the bumper. Than i heat it with a hairdryer, near the side-end of Chasis. The bumper will lift his ends. I do it carefully, until the sideends of the Bumber ar a little higher, than i stop heating.
With this bumper i drive since a year.
At my car, only the side-ends of bumper will come down, never the middle part.
i hope, it will help you.
If not, place a rod between bodymount and End of the Bumper on the sides
Leichtmetall
Leichtmetall is offline  
Reply With Quote
Old 11-19-2014, 11:39 AM
  #274  
Tech Rookie
 
Join Date: Nov 2008
Posts: 9
Default A rumor

I was told by a racing mate that Edam razor has a number of interchangeable parts with the MRX4. I have an old MRX4 lying in the corner, stopped use due to lack of available parts after a big crash, just wanted to know, if this is actually true and if so, would it be possible to rebuild from Edam spare parts? Parts in questions is mainly right side upper arm and rear bulkhead

Thanks, Jon
jnthnchai is offline  
Reply With Quote
Old 11-19-2014, 09:48 PM
  #275  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,092
Trader Rating: 21 (100%+)
Default

the arm should not be a problem the rear bulkhead i am not sure about
azeroth is offline  
Reply With Quote
Old 07-14-2015, 02:59 AM
  #276  
Tech Rookie
 
pipcars's Avatar
 
Join Date: Sep 2008
Location: UK Surrey
Posts: 18
Default Razor

Hi I'm new here, are you guys still running the Razor? Cheers
pipcars is offline  
Reply With Quote
Old 07-14-2015, 12:08 PM
  #277  
Tech Elite
iTrader: (4)
 
Phil Trotta's Avatar
 
Join Date: Feb 2005
Posts: 2,460
Trader Rating: 4 (100%+)
Default

Originally Posted by pipcars View Post
Hi I'm new here, are you guys still running the Razor? Cheers
I have a brand new one in box in opened parts bags for sale
Phil Trotta is offline  
Reply With Quote
Old 07-14-2015, 05:27 PM
  #278  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,092
Trader Rating: 21 (100%+)
Default

there are a few still running them still a decent club car for sure
azeroth is offline  
Reply With Quote
Old 07-15-2015, 02:29 AM
  #279  
Tech Rookie
 
pipcars's Avatar
 
Join Date: Sep 2008
Location: UK Surrey
Posts: 18
Default

Cheers guys.
pipcars is offline  
Reply With Quote
Old 07-27-2015, 12:25 AM
  #280  
Tech Initiate
 
TrkSideRCRacing's Avatar
 
Join Date: Jun 2015
Location: Australia
Posts: 47
Default

still a good car for the club etc... hope they work on a update... afforfable racer for most..
TrkSideRCRacing is offline  
Reply With Quote
Old 09-22-2015, 09:26 AM
  #281  
Tech Addict
iTrader: (11)
 
Join Date: Nov 2014
Posts: 576
Trader Rating: 11 (100%+)
Default

Parts support still OK with this Razor 2?
robracing is offline  
Reply With Quote
Old 09-22-2015, 07:09 PM
  #282  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,092
Trader Rating: 21 (100%+)
Default

https://www.facebook.com/Davidboyles...age_fan_invite US Importer
azeroth is offline  
Reply With Quote
Old 10-06-2015, 02:41 PM
  #283  
Tech Initiate
 
Join Date: Oct 2015
Posts: 43
Default

Originally Posted by robracing View Post
Parts support still OK with this Razor 2?
just started building mine for toledo action next spring. had to make a decision since the 966 is done. david having good parts support and the weak dollar here makes this car a good fit. besides i'm just a club racer anyway.
jpatrick is offline  
Reply With Quote
Old 12-18-2015, 06:28 AM
  #284  
Tech Addict
iTrader: (11)
 
Join Date: Nov 2014
Posts: 576
Trader Rating: 11 (100%+)
Default

Has anyone fitted a reverse clutch to this car? i.e. Capricorn, Xray, etc.? Thanks
robracing is offline  
Reply With Quote
Old 12-18-2015, 07:44 AM
  #285  
Tech Champion
 
Roelof's Avatar
 
Join Date: Aug 2007
Location: Holland
Posts: 6,683
Default

If the dimensions of the clutch is the same as the one on the Protech XR8 (Edam production) I had you can run a complete Mugen clutch.
Roelof is offline  
Reply With Quote

Thread Tools
Search this Thread

Contact Us Archive Advertising Cookie Policy Terms of Service