Go Back  R/C Tech Forums > General Forums > Nitro On-Road
1/8th Nitro On-Road - Edam Razor >

1/8th Nitro On-Road - Edam Razor

1/8th Nitro On-Road - Edam Razor

Reply

Old 01-03-2014, 02:18 PM
  #256  
Tech Apprentice
 
Leichtmetall's Avatar
 
Join Date: Aug 2009
Location: Bavaria, Germany
Posts: 82
Default

Originally Posted by azeroth View Post
i think i would like to see this for the razor 2

http://www.edamhobby.com/product-det...30710-019601#p
i had this slide-type-servosaver in my Razor II. It gave more steering, but the cauge of steering track rod will also change. and then i had a disharmonic car, sometimes oversteer, sometimes understeer. i prefer the little change in stock-servo-saver i wrote some posts before
LM
Leichtmetall is offline  
Reply With Quote
Old 01-03-2014, 02:28 PM
  #257  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,097
Trader Rating: 21 (100%+)
Default

was going to make that mod on the aluminum one but there is not enough material and i have had issues with the plastic one not returning all the way to the same place every time i think i have that fixed now but we shall see
azeroth is offline  
Reply With Quote
Old 02-08-2014, 12:08 PM
  #258  
Tech Apprentice
 
Leichtmetall's Avatar
 
Join Date: Aug 2009
Location: Bavaria, Germany
Posts: 82
Default

bringing in the two new holes in stock-saver, the steering rods are a little clother together. I took sand-paper an made the outside a little smaler, then it works. Until now, no one of the Rodends were broken
LM
Leichtmetall is offline  
Reply With Quote
Old 06-28-2014, 04:04 PM
  #259  
Tech Apprentice
 
Leichtmetall's Avatar
 
Join Date: Aug 2009
Location: Bavaria, Germany
Posts: 82
Default

Is here still any Action?
Edam-Drivers still in Racing?
Leichtmetall
Leichtmetall is offline  
Reply With Quote
Old 06-28-2014, 04:29 PM
  #260  
Tech Master
 
Taylorm's Avatar
 
Join Date: Nov 2006
Location: Monclova, Ohio
Posts: 1,655
Default

Originally Posted by Leichtmetall View Post
Is here still any Action?
Edam-Drivers still in Racing?
Leichtmetall
Yes.. 3 of us are running the car in Toledo.. USA
Taylorm is offline  
Reply With Quote
Old 06-28-2014, 07:15 PM
  #261  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,097
Trader Rating: 21 (100%+)
Default

if it wasn't for job stuff come up for today there would be at least one in this weekends Byron's challange hoping maybe to run tomorrows last chance and get in
azeroth is offline  
Reply With Quote
Old 06-29-2014, 05:59 AM
  #262  
Tech Master
 
Join Date: Apr 2010
Posts: 1,098
Default

Originally Posted by Taylorm View Post
Yes.. 3 of us are running the car in Toledo.. USA
factory driver or just drive a edam?
as i know they only sponser through local distributor,not direct to the manufacturer
kyosho malaysia is offline  
Reply With Quote
Old 06-29-2014, 06:16 AM
  #263  
Tech Master
 
Taylorm's Avatar
 
Join Date: Nov 2006
Location: Monclova, Ohio
Posts: 1,655
Default

Originally Posted by kyosho malaysia View Post
factory driver or just drive a edam?
as i know they only sponser through local distributor,not direct to the manufacturer
..we all just drive...no sponsors....club racing primarily
Taylorm is offline  
Reply With Quote
Old 06-29-2014, 07:27 PM
  #264  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,097
Trader Rating: 21 (100%+)
Default

right maybe a freebee part now and again
azeroth is offline  
Reply With Quote
Old 07-04-2014, 04:38 PM
  #265  
Tech Apprentice
 
Leichtmetall's Avatar
 
Join Date: Aug 2009
Location: Bavaria, Germany
Posts: 82
Default

A question about the Brake:
Which Brakedisc you are using? The original 3-Part Brake-Disc or the on-piece-brake-disc (Option-Part) Or is anyone using another Disc? And, how are your Experience?
Thanks
LM
Leichtmetall is offline  
Reply With Quote
Old 07-04-2014, 07:52 PM
  #266  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,097
Trader Rating: 21 (100%+)
Default

in car 1 i have the original brake settings wander badly lap to lap on the second car have the one piece it is better i also have springs installed between the brake pads which helped along with the aluminum brake arm which helped it be more consistent but is sensitive to adjustment
azeroth is offline  
Reply With Quote
Old 07-05-2014, 12:55 PM
  #267  
Tech Apprentice
 
Leichtmetall's Avatar
 
Join Date: Aug 2009
Location: Bavaria, Germany
Posts: 82
Default

I ask, because i changed to the one-piece-disk. With original, i had no Problems during a Race, but after each Race, i hat fo file off the little "curbs" around the pin-holes. if i forgot it, ich had problems next race. And in 2 Years, i had two broken brakecoolers.
So i changed to the one piece disk. But at first race with it, i had the problem, that the brake was after 5 fast rounds "away", so i gave a little more, and after a few rounds, i had to much brake. up and down. And, im not sure if it was a problem with the disk, such as the spirit had with the brake, or if it was a Problem because it was a completely new builded car with now run in from the Brake.
My Teammate changed to a another disk, i dont know which brand, and he had to change teh stopper of brakeshoe on the bridge and the chasis, because the disk has more thickness. And he is absolutely happy with it.
And im searching the failure
LM
Leichtmetall is offline  
Reply With Quote
Old 07-05-2014, 05:05 PM
  #268  
Tech Master
 
Taylorm's Avatar
 
Join Date: Nov 2006
Location: Monclova, Ohio
Posts: 1,655
Default

..I was having an intermittent problem with brake disc binding when I first built the car...I shaved some of the right bulkhead away and thought I had it cured.....last club race it was binding again...maybe it's the disc....going to see what other disc may fit.....anyone ever use a carbon disc???.....pros/cons???...
Taylorm is offline  
Reply With Quote
Old 07-06-2014, 09:06 AM
  #269  
Tech Apprentice
 
Leichtmetall's Avatar
 
Join Date: Aug 2009
Location: Bavaria, Germany
Posts: 82
Default

Problem with Brake? touching the bulkhead?
Are you sure, that you mount the brakepads correct? The Ends of the brakepads are different. be sure, that you mount the correct direction
LM
Leichtmetall is offline  
Reply With Quote
Old 07-06-2014, 04:56 PM
  #270  
Tech Master
iTrader: (21)
 
azeroth's Avatar
 
Join Date: Aug 2009
Location: Da Burbs
Posts: 1,097
Trader Rating: 21 (100%+)
Default

is there anybody elses front bumper that fits this chassis i really hate that they end up sagged down and goodbye steering towards the end of a run
azeroth is offline  
Reply With Quote

Thread Tools
Search this Thread

Contact Us Archive Advertising Cookie Policy Terms of Service