R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Nitro On-Road

Reply
 
Thread Tools Search this Thread
Old 12-01-2008, 04:55 AM   #1
Tech Rookie
 
Join Date: Nov 2008
Posts: 13
Default [Question] Servo's for 1/8 cars

Hello people,, im new here and i need your help on something..

Some years ago i bought these parts for my picco integra
a Sanwa MX-3 radio controller,2x Sanwa SX-112 that came with the controller , i also have a Hitec HS-5945MG digital servo for my steering..and i need your help on that because i think that it is too slow .. it hasn't been reprogrammed or anything and i would like you to tell me if that could be the problem..

I also have a 6V battery that i don't have the recharger of. :x

Plus that the controller's steering wheel isn't turning in full turns it is limited at 90 degrees and i can't get that much presicion out of it.

What would you suggest me to do?Because i don't think that my setup is really working..sorry for the nooby questions..don't flame me for that k?

Finally something irrelevant.. i haven't run the car for 5 years or so and i didn't put any oil in it so there maybe some rust in the crankshaft (i hope not!) do you know anything that could get rid of the carbon build-up and all else that accumulated over the years inside the engine?
Currently i have heard about anti-freeze ,brake cleaners, denaturated alcohol,and methanol so what would be the best for my case?



I saw this RCM 50W Ultrasonic Cleaner 220V would it help me get the dirt out of the engine?

Ok something else i need to replace the ball bearings will these be ok for me? Is it 12$ for each of them ?wtF???

Sorry if i made you dizzy with all these questions but i need to get the car back into tracks.

Last edited by darkie; 12-01-2008 at 05:16 AM.
darkie is offline   Reply With Quote
Old 12-01-2008, 12:57 PM   #2
Tech Apprentice
 
ABRacing's Avatar
 
Join Date: Nov 2008
Location: Oregon
Posts: 81
Trader Rating: 7 (100%+)
Default Servo answer

I had that Hitech servo in my touring car and took it out it isn't good at all 0.13 speed is ok for when I raced dirt but for onroad I like .010. Try the airtronics 94358(more torque), or 94357(more speed). Also make sure you use a good throttle servo it makes a big difference in being smooth.
__________________
AntonBrownRacing.com
Team Timezone Racing

Last edited by ABRacing; 12-01-2008 at 01:13 PM.
ABRacing is offline   Reply With Quote
Old 12-02-2008, 02:03 AM   #3
Tech Rookie
 
Join Date: Nov 2008
Posts: 13
Default

Ok thank you for posting i have two stuck head screws the Allen head is kinda round and i can't get any grip out of them can somebody help me with that?

Last edited by darkie; 12-02-2008 at 02:14 AM.
darkie is offline   Reply With Quote
Old 12-04-2008, 08:15 PM   #4
Tech Regular
 
ESWLFSE's Avatar
 
Join Date: Nov 2007
Location: Terra Ceia, FL
Posts: 326
Trader Rating: 7 (100%+)
Send a message via Yahoo to ESWLFSE
Default

When all else fails I cut a slot in them with a Dremel and use a flat blade screwdriver to remove them.

On the old motor you can either do a complete teardown, inspection and cleanup and possibly with new bearings or.... just warm it up to 180, fuel it up, prime the fuel line, pull the glow plug, open the carb, choke the carb, and crank it until you get a nice spray out of the glow plug hole - then pull the fuel line and crank it until the fuel spray clears - then reinstall the plug and fuel line and start it up.
ESWLFSE is offline   Reply With Quote
Old 12-04-2008, 08:20 PM   #5
Tech Adept
 
Join Date: May 2008
Location: SIMI VALLEY CA
Posts: 245
Default

There you go thats what i would do if i ever stripped one,never done that before tho.
__________________
Mugen USA-FX Hobbies-Airtronics
TONY CLARK
STRICTLYSERPENT is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
Team Corally RDX Touring Car Kenshin Electric On-Road 10561 11-21-2015 12:54 AM
calling all FUTABA 3PK users..... JayBee Radio and Electronics 1312 01-25-2015 08:57 AM
New Hot Bodies Buggy!!??????? monsteraddict Nitro Off-Road 14489 03-18-2013 02:42 PM
The Nitro Pit Dbackmasta Arizona-New Mexico Racing 18732 09-13-2012 09:27 AM
Does price indicate quality and would you buy again??? Falcon XR- Nitro Off-Road 26 04-17-2008 12:51 AM
2007 WINTER NATIONAL! SuperDaveNT Canadian R/C Scene 1078 05-25-2007 07:44 AM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 01:49 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net