R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Nitro On-Road

Reply
 
Thread Tools Search this Thread
Old 09-16-2002, 06:28 PM   #4021
Tech Elite
 
kevink2's Avatar
 
Join Date: Nov 2001
Location: Glendale, Calif.
Posts: 2,154
Default

Quote:
Originally posted by asd
man! you guys are old! lol
daughters? wifes? sons?
I'M NOT EVEN IN HIGH SCHOOL YET!
Yeah I could tell!
kevink2 is offline   Reply With Quote
Old 09-16-2002, 06:31 PM   #4022
Tech Regular
 
Join Date: Sep 2002
Posts: 326
Default

hey, be nice. there's old people and young people on this forum of course. but as older folk, we should be the ones to lead by example. I'm 26, i guess that's old? lol
calimassive is offline   Reply With Quote
Old 09-16-2002, 06:32 PM   #4023
Tech Elite
 
kevink2's Avatar
 
Join Date: Nov 2001
Location: Glendale, Calif.
Posts: 2,154
Default

Quote:
Originally posted by asd
man, i have so many stripped screws!lol, any suggestions on how to avoid this?
Buy a posi driver, or grind down your phillips flatter with a dremel... tip from an old fart.
kevink2 is offline   Reply With Quote
Old 09-16-2002, 06:43 PM   #4024
asd
Tech Addict
 
Join Date: Aug 2002
Location: Toronto, Ontario
Posts: 530
Send a message via ICQ to asd
Default

posi driver?
thxs u old fart
asd is offline   Reply With Quote
Old 09-16-2002, 06:45 PM   #4025
Tech Elite
 
kevink2's Avatar
 
Join Date: Nov 2001
Location: Glendale, Calif.
Posts: 2,154
Default

Quote:
Originally posted by asd
posi driver?
thxs u old fart
They look just like phillips heads but shorter and stockier... they'll fit in the heads better, young man!
kevink2 is offline   Reply With Quote
Old 09-16-2002, 06:50 PM   #4026
asd
Tech Addict
 
Join Date: Aug 2002
Location: Toronto, Ontario
Posts: 530
Send a message via ICQ to asd
Default

lol, do u know how much they are in canadian dollars and where i could get them?
asd is offline   Reply With Quote
Old 09-16-2002, 11:44 PM   #4027
Tech Addict
 
Pirvan's Avatar
 
Join Date: Aug 2002
Location: Singapore/Australia/India
Posts: 511
Default Two speed shaft

Hi Guys, i was just wondering about something.

When i dismantled the clutch and 2 speed on my RS12 and tried to fit it to a CVR, i noticed that the shaft on the CVR was not long enough. Is the longish shaft (is that the 2 speed pilot shaft)on the RS12 removable? And do i have to transfer that shaft onto the CVR to fit the 2 speed? If so, how do i go about doing it?

Thanks

Jeff

Last edited by Pirvan; 09-17-2002 at 12:29 AM.
Pirvan is offline   Reply With Quote
Old 09-17-2002, 12:39 AM   #4028
rjl
Tech Fanatic
 
rjl's Avatar
 
Join Date: Jun 2002
Location: OZ
Posts: 848
Default

If you ure using the 3D clutch you must have an engine with SG shaft.
rjl is offline   Reply With Quote
Old 09-17-2002, 05:41 AM   #4029
dtm
Tech Champion
 
dtm's Avatar
 
Join Date: Aug 2001
Location: HKG
Posts: 7,551
Send a message via ICQ to dtm
Default

Quote:
Originally posted by rjl
If you ure using the 3D clutch you must have an engine with SG shaft.
Or a std shaft with a converter like what Mugen makes!
dtm is offline   Reply With Quote
Old 09-17-2002, 06:05 AM   #4030
Tech Elite
 
AMGRacer's Avatar
 
Join Date: Oct 2001
Location: Brisbane, Australia
Posts: 3,939
Default Re: Two speed shaft

Quote:
Originally posted by Pirvan
Hi Guys, i was just wondering about something.

When i dismantled the clutch and 2 speed on my RS12 and tried to fit it to a CVR, i noticed that the shaft on the CVR was not long enough. Is the longish shaft (is that the 2 speed pilot shaft)on the RS12 removable? And do i have to transfer that shaft onto the CVR to fit the 2 speed? If so, how do i go about doing it?

Thanks

Jeff
Hey Pirvan give me a call and I can help you out with this!! I will be at the track tomorrow.
AMGRacer is offline   Reply With Quote
Old 09-17-2002, 06:07 AM   #4031
rjl
Tech Fanatic
 
rjl's Avatar
 
Join Date: Jun 2002
Location: OZ
Posts: 848
Default

For all the voner fans out there, Simon Camilleri from Oz is fifth fastest after timed practice, Simon is as close as you can get to a privateer. He runs only the same equipment that you or I would have. I don't think he would be driving a Serpent as listed, to the best of my knowledge he is using the V-one-RR with JP-S3 engine. If Simon can make the A, I think he may be a threat to the "names". Good luck you little ozzie bleeder!!!!!!!!!!
rjl is offline   Reply With Quote
Old 09-17-2002, 06:09 AM   #4032
rjl
Tech Fanatic
 
rjl's Avatar
 
Join Date: Jun 2002
Location: OZ
Posts: 848
Default

AMG you going to race at the Nats?
rjl is offline   Reply With Quote
Old 09-17-2002, 06:27 AM   #4033
Tech Elite
 
AMGRacer's Avatar
 
Join Date: Oct 2001
Location: Brisbane, Australia
Posts: 3,939
Default

Quote:
Originally posted by rjl
AMG you going to race at the Nats?
I am planning to!!

Man I cannot believe Simon is going that well!! I saw him race about 4 weeks ago at the QLD nationals and he was DANG fast there, but his engine was not as fast as the likes of the "sponsored" boys. I hope he brings home a trophy!!
AMGRacer is offline   Reply With Quote
Old 09-17-2002, 06:54 AM   #4034
Tech Master
 
patelladragger's Avatar
 
Join Date: Jan 2002
Posts: 1,638
Send a message via AIM to patelladragger
Default

I wish simon ALL the luck cause I'd like to see a V1R in the mains. But the guys are still playing cat and mouse and not showing their true times,it's going to be tough to get in the A when hell the factory boys have had got the eduardo and alberto there! geezus - anybody think 200mm nitro isn't the future of RC? The rossi brothers are there too!
patelladragger is offline   Reply With Quote
Old 09-17-2002, 07:25 AM   #4035
Tech Regular
 
Join Date: Sep 2002
Posts: 326
Default

who are eduardo and alberto? Italian engine designers I'm assuming? im confused.

go Kyosho V1rr !!!, good car, it deserves to win something. I get the feeling it hasnt been blessed with a great driver as of yet. Maybe somone will surprise us.

Last edited by calimassive; 09-17-2002 at 07:29 AM.
calimassive is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
Kyosho VoneR Roller $120 Tag R/C Items: For Sale/Trade 4 08-06-2003 07:22 PM
kyosho VoneR w/ nova, pipe $200 Tag R/C Items: For Sale/Trade 9 07-25-2003 03:09 AM
Kyosho VoneR Macky R/C Items: For Sale/Trade 6 07-31-2002 09:04 AM
Brand new Kyosho VoneR kit $230 Tag R/C Items: For Sale/Trade 0 10-22-2001 02:12 PM
NIB Kyosho VoneR $250 Tag R/C Items: For Sale/Trade 4 10-21-2001 06:39 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 10:53 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net