Go Back  R/C Tech Forums > General Forums > Nitro Off-Road
Kyosho Inferno MP9 TKI4 1/8 Buggy Kit >

Kyosho Inferno MP9 TKI4 1/8 Buggy Kit

Like Tree314Likes

Kyosho Inferno MP9 TKI4 1/8 Buggy Kit

    Hide Wikipost
Old 11-05-2018, 09:06 AM   -   Wikipost
R/C Tech ForumsThread Wiki: Kyosho Inferno MP9 TKI4 1/8 Buggy Kit
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: 30Tooth
Picked up a TKI3 and want to upgrade to TKI4 ? Here are all the updated parts:

Shocks

IF347-155 1.5X5 Pistons
IF471-01 Front Shock Body
IF470-01 Rear Shock Body
IF470-03BK Shock Adjust Dial
IFW154 Boots
IF346-05C Shock End Set

Wing

IF491BK Wing
IFW460B Wing Mount/Stay

Rear End

IFH006W Wheel
IF490 HUB
IF490-01 Hub Insert
IF492 Shock Pin
IF423HB Rear Arm
IF287 Hard Upper Rod Rear

Front End

IF489 Steering Rod Set
IF488 Knuckles
IF487H Front Arm
IFW458 Hard Lower Pin
IFW425 93MM CVD
IF286 Hard Upper Rod
IF486 Lower Susp Holder
IFW459 Servo Saver (Hard)
IF446B Ackerman Arm
IF426-64.5 Susp Shaft


Other

IF469B Filter
97035LW-13 Clutch Bell
IF453B Body Mount
IFW107GM Hexes
W300910 Washer
IF443B Center Diff Plate
IF444C Tank
IF479B Radio Box
96772 13x16x0.15mm Shim
IF481B Fuel Tank Stay
IFW336GM Wheelnut
IFB008 TKI4 Body
IFD403W TKI4 Decal

---------------------------

Another option if you want TKI4 Durability but TKI3 geometry of the front arm is :

IF493 Front Arm (Updated MP9 front arms replaces IF427B as a direct fit. Left and right.)

They use the older TKI3 captured outer hinge pin and screw. But if you just reem out the the outer hole you can use TKI hinge-pin/nut (IFW458)
---------------------------

Optional Updates / New Parts:

IFW469 IFW469 Aeration Cap Set(Threaded Big Shock/MP9)

IFW473 New Brake Pads (Sept 2017)

Optional Alu front hubs:
- IFW412 - 13 deg (like stock plastic ones)
- IFW436 - 16 deg
- IFW474 - 17.5 deg
- IFW461 - 19deg

M2C 1mm engine spacer: M2C9610

Body Options
New Bitty Force Body

Tebo's Build Videos

Video #1

Video #2

Video #3

Video #4

Video #5

Video #6

Original Kyosho MP9 TKI Thread
_____________________

Baseline setups from Joonas.




_____________________

Shock build with vented cap and compensator.

You have to use the HC diaphragms (if346-09,stock TKI3 and if not mistaken TKI4 too, yes the thin ones no one likes), aeration caps without the bleeder screw or mod the stock caps by drilling a 1.5 or 2mm hole on the top facing up or at an angle (doesn't matter the size or angle, it just for bleeding pressure behind the diaphragm and allow the foam compensator to breathe) and a 10mm width x 3.5mm height dome shaped foam compensator made from old open cell inserts or dishwasher sponge. The foam compensator has to be soft enough not to add rebound but allow the diaphragm to regain it's shape.

Setup Sheet and Tuning

The setup sheet is getting crowded with all options but don't worry once you get acquainted with the parts will make sense.
Run the car as is, more than probably you won't need anything else. Using my setup as an example:

Diff gear has two options, normal and LSD. LSD stands for limited slip differential and is like using thick oils because you can't tune coast from locked.

Shock setup is a bit more confusing, you have two shock body sizes (S and M and truggy sized rear shocks that only the first version had so forget this one), three types of pistons (flat holes and surfaces, flat holes tapered surface and tapered holes with tapered surface): tapered have most pack, then black(simple piston) and then white because length of the holes. Then you have different length springs to account for different shock sizes, for a standard wheelbase/no weights car a good combo is Light Blue front and Orange rear, if you extend the wheelbase then I expect the included Light Blue rear springs be money instead of Orange.

Ride height is self explanatory, start always with lower arms parallel because good suspension geometry will be far easier to achieve. Rebound is used as total shock length no idea why they call it rebound, either use total shock length or maximum exposed shock shaft length. Camber self explanatory, run more camber in the front than the rear to make the car oversteer and more rear than front to make it understeer(grossly oversimplified).

Toe same deal as camber(again grossly oversimplified) but this you have to run the least amount you can. I use around 2-2.5 on my cars, never more as I can find traction by other means with way less impact on performance.

Wheelbase is a powerful setting, changes a lot of stuff. Let's just say that it can make the car behave neutral or not in that small range. Try for yourself. I like to use the longest setting and tune from there.

Shock position self explanatory, something most don't change and I don't play around with it. I do have a method but involves much work (with the car bottomed out, see which position places the shock 90 to the lower arm and then chose spring from a couple equations and bam done, I can do it easily so anyone interested just ask.

Rear upper arm position is again an important setting, you change both camber gain and roll centre. The rear roll centre should be higher than the front, that's why I use the middle hole inner row as a starting setup.

Suspension arm, self explanatory: there are two different length arms and each has a hard and a normal flex plastic.

Front suspension bushing is for upper arm alignment, also same deal as rear upper arm position changes both camber gain and roll centre.

Suspension holder is for kick up (pro dive is the correct naming). I believe tki4 9 of kick up to be better than 9 of kick up using the tki3 parts because you can run the car lower (26mm front ride height) and use the +2mm front shock tower if there's too much camber gain or it's stiff in roll. So use +2mm lowered roll centre to keep most stuff unchanged or use the bushings with the dot up to lower the roll centre a bit more, doesn't hurt anything.

Front hub carrier, self explanatory. I am trying to use the out hole on top of the carrier as it is better during braking and accelerating. Together with the higher front roll centre on the tki4 should provide enough camber gain during cornering if not then more caster will do.

Rear roll centre and anti squat(wrongly called skid angle). Again same thinking as the front, lower the car and keep roll centre in the same height as before(that will need a change in upper arm position which my setup does). Anti squat is changed only if the pitching motion causes too much camber to be gained by the rear tires on power, nothing more.

Front knuckle, apparently there's a difference in the Ackerman arm. Can't say anything about them as I don't know enough about both.

Rear hub carrier,there is one made of plastic (which doesn't have offset apparently so it's suited to long arm setting) and three aluminium versions. One similar to the plastic one, other with offset and a new one with offset and adjustable hub height.

Rear tread can be used as arm length and outboard toe(never seen it being used but the possibility is there). Longer is better most of the time (only on really low traction).

Chassis brace, wheel hub, sway bars and weight are self explanatory. No need to use weights nor other hubs. A couple of roll bars would be a nice addition. About the aluminium braces I am torn, I guess the car doesn't need flex with this setup but won't recommend the stiffer braces but the lower engine mount is very nice to deal with flex around the clutch.

Wing and wing stay are like the d81x had regarding height and position. The wing should be as low and have free airflow as possible.

Print Wikipost

Old 10-18-2016, 07:20 PM
  #781  
Tech Adept
 
Join Date: Sep 2015
Posts: 156
Default

Have any of you guys seem Tebo's set up from the worlds?
Ofna2005 is offline  
Old 10-18-2016, 07:47 PM
  #782  
Tech Master
iTrader: (8)
 
jeromerc's Avatar
 
Join Date: May 2012
Location: Vietnam
Posts: 1,085
Trader Rating: 8 (100%+)
Default

Originally Posted by Ofna2005
Have any of you guys seem Tebo's set up from the worlds?
He just posted it on Facebook yesterday
jeromerc is offline  
Old 10-18-2016, 07:49 PM
  #783  
Tech Master
iTrader: (8)
 
jeromerc's Avatar
 
Join Date: May 2012
Location: Vietnam
Posts: 1,085
Trader Rating: 8 (100%+)
Default

Originally Posted by rotor head33
I need a new chassis but can't decide, should I get the m2c or the kyosho hardened chassis?
Both are great, M2C is cheaper and has inserts where the droop screws go and the skid plates. I have ran the M2C, Foroni, stock Kyosho and the hardened kyushu chassis. All are great but I like the M2C and Foroni better because of the droop screw area on both, then the M2C has the skid plates putting it up just a bit over the rest
jeromerc is offline  
Old 10-18-2016, 08:23 PM
  #784  
Tech Addict
iTrader: (11)
 
Join Date: May 2009
Posts: 718
Trader Rating: 11 (100%+)
Default

Ok cool I'll look at the foroni as well
rotor head33 is offline  
Old 10-19-2016, 12:26 PM
  #785  
Tech Addict
iTrader: (22)
 
ragekills's Avatar
 
Join Date: Aug 2007
Location: Los Angeles
Posts: 736
Trader Rating: 22 (100%+)
Default

TKI4 instantly leans out when flipped any suggestions? (I have to keep revving it to stay on as it wants to turn off) Fuel line is ran around body post, motor is tuned properly.

This has been since day 1

Thx
-J
ragekills is offline  
Old 10-19-2016, 12:33 PM
  #786  
Tech Regular
iTrader: (1)
 
shannow's Avatar
 
Join Date: May 2007
Location: France Paris
Posts: 404
Trader Rating: 1 (100%+)
Default

Maybe an air leak on the fuel line? Or like my mate the spring on the fuel tank was getting weak and the lid would leak especially upside down.
shannow is offline  
Old 10-19-2016, 12:59 PM
  #787  
Tech Lord
iTrader: (359)
 
tobamiester's Avatar
 
Join Date: Jul 2009
Location: Tea drinking Limmey in NJ
Posts: 12,321
Trader Rating: 359 (100%+)
Default

yeah sounds like a pressure line issue..

Last edited by tobamiester; 10-19-2016 at 02:02 PM.
tobamiester is offline  
Old 10-19-2016, 01:40 PM
  #788  
Tech Regular
iTrader: (6)
 
Join Date: Feb 2010
Location: Grimsby, Ontario Canada
Posts: 348
Trader Rating: 6 (100%+)
Default

Originally Posted by ragekills
TKI4 instantly leans out when flipped any suggestions? (I have to keep revving it to stay on as it wants to turn off) Fuel line is ran around body post, motor is tuned properly.

This has been since day 1

Thx
-J
There could also be a leak in the fuel tank even from new. It's happened to me before as I had the same issue.
flap jack is offline  
Old 10-19-2016, 02:17 PM
  #789  
Tech Addict
iTrader: (22)
 
ragekills's Avatar
 
Join Date: Aug 2007
Location: Los Angeles
Posts: 736
Trader Rating: 22 (100%+)
Default

Thanks guys! I will replace the fuel line and go from there.
ragekills is offline  
Old 10-19-2016, 02:27 PM
  #790  
Tech Addict
iTrader: (22)
 
ragekills's Avatar
 
Join Date: Aug 2007
Location: Los Angeles
Posts: 736
Trader Rating: 22 (100%+)
Default

Also is there an incorrect way to install the fuel filter? I've seen them installed both way. The correct way seems to be the O-ring facing the front of the buggy.

-J
ragekills is offline  
Old 10-19-2016, 03:13 PM
  #791  
Tech Adept
 
Cant drive's Avatar
 
Join Date: May 2016
Location: Orange County California
Posts: 160
Default

Originally Posted by ragekills
Also is there an incorrect way to install the fuel filter? I've seen them installed both way. The correct way seems to be the O-ring facing the front of the buggy.

-J
You want the O ring to face the carb inlet. That way the fuel filter can actually hold any debri that may get into the tank. If it's the other way, it can potentially get blocked.
Cant drive is offline  
Old 10-21-2016, 08:19 AM
  #792  
Tech Addict
iTrader: (22)
 
ragekills's Avatar
 
Join Date: Aug 2007
Location: Los Angeles
Posts: 736
Trader Rating: 22 (100%+)
Default

Thank you!
ragekills is offline  
Old 10-23-2016, 02:10 AM
  #793  
Tech Fanatic
 
vandalzzz's Avatar
 
Join Date: Jul 2013
Location: somewhere near Japan
Posts: 762
Default

So, i've pulled the Red K-trigger, waiting for my kit now.
One question: is it possible to fit both fuel filter on its stock place and losi-style air filer? I've seen someone's TKI4 photo from past World Champ with losi filter at NB site, but can't remember where his fuel filter was fitted.
vandalzzz is offline  
Old 10-23-2016, 08:46 AM
  #794  
Tech Master
iTrader: (42)
 
Join Date: May 2009
Posts: 1,121
Trader Rating: 42 (98%+)
Default

why would you want to do that in the first place??? Kyosho filters are the best
RockStar_199 is offline  
Old 10-23-2016, 09:09 AM
  #795  
Tech Elite
iTrader: (16)
 
HaulinBass's Avatar
 
Join Date: Dec 2004
Location: grande prairie alberta canada
Posts: 3,096
Trader Rating: 16 (100%+)
Default

Lol the inline fuel filter isn't really a filter at all just a place to hold extra fuel. If anything is small enough to make it through the brass filter in the tank a little mesh screen isn't going to stop anything.
I stopped running them altogether as it's just another spot a leak or failure can happen
1evo RRR Driver likes this.
HaulinBass is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell or Share My Personal Information -

Copyright © 2023 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.