Go Back  R/C Tech Forums > General Forums > Nitro Off-Road
Kyosho Inferno MP9 TKI4 1/8 Buggy Kit >

Kyosho Inferno MP9 TKI4 1/8 Buggy Kit

Like Tree270Likes

Kyosho Inferno MP9 TKI4 1/8 Buggy Kit

    Hide Wikipost
Old 11-05-2018, 09:06 AM   -   Wikipost
R/C Tech ForumsThread Wiki: Kyosho Inferno MP9 TKI4 1/8 Buggy Kit
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: 30Tooth
Picked up a TKI3 and want to upgrade to TKI4 ? Here are all the updated parts:

Shocks

IF347-155 1.5X5 Pistons
IF471-01 Front Shock Body
IF470-01 Rear Shock Body
IF470-03BK Shock Adjust Dial
IFW154 Boots
IF346-05C Shock End Set

Wing

IF491BK Wing
IFW460B Wing Mount/Stay

Rear End

IFH006W Wheel
IF490 HUB
IF490-01 Hub Insert
IF492 Shock Pin
IF423HB Rear Arm
IF287 Hard Upper Rod Rear

Front End

IF489 Steering Rod Set
IF488 Knuckles
IF487H Front Arm
IFW458 Hard Lower Pin
IFW425 93MM CVD
IF286 Hard Upper Rod
IF486 Lower Susp Holder
IFW459 Servo Saver (Hard)
IF446B Ackerman Arm
IF426-64.5 Susp Shaft


Other

IF469B Filter
97035LW-13 Clutch Bell
IF453B Body Mount
IFW107GM Hexes
W300910 Washer
IF443B Center Diff Plate
IF444C Tank
IF479B Radio Box
96772 13x16x0.15mm Shim
IF481B Fuel Tank Stay
IFW336GM Wheelnut
IFB008 TKI4 Body
IFD403W TKI4 Decal

---------------------------

Another option if you want TKI4 Durability but TKI3 geometry of the front arm is :

IF493 Front Arm (Updated MP9 front arms replaces IF427B as a direct fit. Left and right.)

They use the older TKI3 captured outer hinge pin and screw. But if you just reem out the the outer hole you can use TKI hinge-pin/nut (IFW458)
---------------------------

Optional Updates / New Parts:

IFW469 IFW469 Aeration Cap Set(Threaded Big Shock/MP9)

IFW473 New Brake Pads (Sept 2017)

Optional Alu front hubs:
- IFW412 - 13 deg (like stock plastic ones)
- IFW436 - 16 deg
- IFW474 - 17.5 deg
- IFW461 - 19deg

M2C 1mm engine spacer: M2C9610

Body Options
New Bitty Force Body

Tebo's Build Videos

Video #1

Video #2

Video #3

Video #4

Video #5

Video #6

Original Kyosho MP9 TKI Thread
_____________________

Baseline setups from Joonas.




_____________________

Shock build with vented cap and compensator.

You have to use the HC diaphragms (if346-09,stock TKI3 and if not mistaken TKI4 too, yes the thin ones no one likes), aeration caps without the bleeder screw or mod the stock caps by drilling a 1.5 or 2mm hole on the top facing up or at an angle (doesn't matter the size or angle, it just for bleeding pressure behind the diaphragm and allow the foam compensator to breathe) and a 10mm width x 3.5mm height dome shaped foam compensator made from old open cell inserts or dishwasher sponge. The foam compensator has to be soft enough not to add rebound but allow the diaphragm to regain it's shape.

Setup Sheet and Tuning

The setup sheet is getting crowded with all options but don't worry once you get acquainted with the parts will make sense.
Run the car as is, more than probably you won't need anything else. Using my setup as an example:

Diff gear has two options, normal and LSD. LSD stands for limited slip differential and is like using thick oils because you can't tune coast from locked.

Shock setup is a bit more confusing, you have two shock body sizes (S and M and truggy sized rear shocks that only the first version had so forget this one), three types of pistons (flat holes and surfaces, flat holes tapered surface and tapered holes with tapered surface): tapered have most pack, then black(simple piston) and then white because length of the holes. Then you have different length springs to account for different shock sizes, for a standard wheelbase/no weights car a good combo is Light Blue front and Orange rear, if you extend the wheelbase then I expect the included Light Blue rear springs be money instead of Orange.

Ride height is self explanatory, start always with lower arms parallel because good suspension geometry will be far easier to achieve. Rebound is used as total shock length no idea why they call it rebound, either use total shock length or maximum exposed shock shaft length. Camber self explanatory, run more camber in the front than the rear to make the car oversteer and more rear than front to make it understeer(grossly oversimplified).

Toe same deal as camber(again grossly oversimplified) but this you have to run the least amount you can. I use around 2-2.5 on my cars, never more as I can find traction by other means with way less impact on performance.

Wheelbase is a powerful setting, changes a lot of stuff. Let's just say that it can make the car behave neutral or not in that small range. Try for yourself. I like to use the longest setting and tune from there.

Shock position self explanatory, something most don't change and I don't play around with it. I do have a method but involves much work (with the car bottomed out, see which position places the shock 90 to the lower arm and then chose spring from a couple equations and bam done, I can do it easily so anyone interested just ask.

Rear upper arm position is again an important setting, you change both camber gain and roll centre. The rear roll centre should be higher than the front, that's why I use the middle hole inner row as a starting setup.

Suspension arm, self explanatory: there are two different length arms and each has a hard and a normal flex plastic.

Front suspension bushing is for upper arm alignment, also same deal as rear upper arm position changes both camber gain and roll centre.

Suspension holder is for kick up (pro dive is the correct naming). I believe tki4 9 of kick up to be better than 9 of kick up using the tki3 parts because you can run the car lower (26mm front ride height) and use the +2mm front shock tower if there's too much camber gain or it's stiff in roll. So use +2mm lowered roll centre to keep most stuff unchanged or use the bushings with the dot up to lower the roll centre a bit more, doesn't hurt anything.

Front hub carrier, self explanatory. I am trying to use the out hole on top of the carrier as it is better during braking and accelerating. Together with the higher front roll centre on the tki4 should provide enough camber gain during cornering if not then more caster will do.

Rear roll centre and anti squat(wrongly called skid angle). Again same thinking as the front, lower the car and keep roll centre in the same height as before(that will need a change in upper arm position which my setup does). Anti squat is changed only if the pitching motion causes too much camber to be gained by the rear tires on power, nothing more.

Front knuckle, apparently there's a difference in the Ackerman arm. Can't say anything about them as I don't know enough about both.

Rear hub carrier,there is one made of plastic (which doesn't have offset apparently so it's suited to long arm setting) and three aluminium versions. One similar to the plastic one, other with offset and a new one with offset and adjustable hub height.

Rear tread can be used as arm length and outboard toe(never seen it being used but the possibility is there). Longer is better most of the time (only on really low traction).

Chassis brace, wheel hub, sway bars and weight are self explanatory. No need to use weights nor other hubs. A couple of roll bars would be a nice addition. About the aluminium braces I am torn, I guess the car doesn't need flex with this setup but won't recommend the stiffer braces but the lower engine mount is very nice to deal with flex around the clutch.

Wing and wing stay are like the d81x had regarding height and position. The wing should be as low and have free airflow as possible.

Print Wikipost

Reply

Old 03-07-2016, 12:59 AM
  #61  
Tech Fanatic
iTrader: (6)
 
Join Date: Apr 2014
Location: Townsville
Posts: 975
Trader Rating: 6 (100%+)
Default

Well its already probably the most stable car around, so more aggressive would make sense, i think its at the point where if you made it any more stable youd just start to lose speed
Gavel is offline  
Reply With Quote
Old 03-07-2016, 03:26 AM
  #62  
Tech Fanatic
iTrader: (46)
 
mourinho's Avatar
 
Join Date: Jun 2013
Posts: 965
Trader Rating: 46 (100%+)
Default

Originally Posted by redbones View Post
Judging from the updates, will it make the car handle more stable or aggressive?
Would like to hear from the K gurus
According to kyosho:
"Built for faster speed than the former TKI3, the new TKI4 features revised front/rear suspension for improved cornering stability and sharp control characteristics. A newly designed body and rear wing produces superior aerodynamics for high-performance cornering and traction."

Clearly the focus is on even more cornering prowess.

Also the durability upgrades.
mourinho is offline  
Reply With Quote
Old 03-07-2016, 05:12 AM
  #63  
Tech Apprentice
 
Join Date: Jul 2010
Posts: 92
Default

Originally Posted by am View Post
Well, at least the moast importent pars are now HA
+1, the rest is all 'eye candy', but with the shock a better coating was needed performance wise.
wouterb is offline  
Reply With Quote
Old 03-12-2016, 04:30 AM
  #64  
Tech Champion
 
Pulse_'s Avatar
 
Join Date: May 2010
Location: Brussels, Belgium
Posts: 5,081
Default

https://www.youtube.com/watch?v=hceyFxDHc5Q
Pulse_ is offline  
Reply With Quote
Old 03-12-2016, 10:42 AM
  #65  
Tech Regular
 
Join Date: May 2005
Posts: 386
Exclamation

Might be two versions

KYOSHO INFERNO MP9 TKI4 SP (w/IFW461)
BRAND: KYOSHO
PART NUMBER: K.33001BSP

and without

Kyosho Inferno MP9 TKI4
BRAND: KYOSHO
PART NUMBER: K.33001B
Andyg01 is offline  
Reply With Quote
Old 03-12-2016, 01:39 PM
  #66  
Tech Initiate
iTrader: (1)
 
Join Date: Apr 2012
Location: Hudson,WI
Posts: 27
Trader Rating: 1 (100%+)
Default tki4

Random question if anyone could please help! I just received parts I ordered from Amain hobbies and I purchased red nylon nuts for the wheels. I put them on and now they literally won't come off. I put new wheels on as well and the inside of the wheels are stripped so it's not possible to get them off. Any tips would be greatly appreciated. Thanks in advance.
GIVITUP is offline  
Reply With Quote
Old 03-12-2016, 03:46 PM
  #67  
Tech Prophet
iTrader: (95)
 
houston's Avatar
 
Join Date: Sep 2004
Location: Sherwood,OR
Posts: 15,743
Trader Rating: 95 (100%+)
Default

If433b
if469b
if453b
if479b
If486
if488
if489
if490
if490-01
ifb008
if492
ifw460b
If487h
if423hb
if491ky
if491bk
houston is offline  
Reply With Quote
Old 03-12-2016, 03:49 PM
  #68  
Tech Prophet
iTrader: (95)
 
houston's Avatar
 
Join Date: Sep 2004
Location: Sherwood,OR
Posts: 15,743
Trader Rating: 95 (100%+)
Default

Originally Posted by GIVITUP View Post
Random question if anyone could please help! I just received parts I ordered from Amain hobbies and I purchased red nylon nuts for the wheels. I put them on and now they literally won't come off. I put new wheels on as well and the inside of the wheels are stripped so it's not possible to get them off. Any tips would be greatly appreciated. Thanks in advance.
Nylon nuts?

You gotta put oil or grease on threads before installing

Stick something through axle joint and remove nut if possible
houston is offline  
Reply With Quote
Old 03-12-2016, 04:40 PM
  #69  
Tech Fanatic
 
Join Date: Aug 2012
Posts: 992
Default

Originally Posted by Pulse_ View Post
very impressive !
bob.less is offline  
Reply With Quote
Old 03-12-2016, 06:07 PM
  #70  
Tech Master
iTrader: (8)
 
jeromerc's Avatar
 
Join Date: May 2012
Location: Vietnam
Posts: 1,085
Trader Rating: 8 (100%+)
Default

are those the new part numbers Monty?
jeromerc is offline  
Reply With Quote
Old 03-12-2016, 08:45 PM
  #71  
Tech Prophet
iTrader: (95)
 
houston's Avatar
 
Join Date: Sep 2004
Location: Sherwood,OR
Posts: 15,743
Trader Rating: 95 (100%+)
Default

Originally Posted by jeromerc View Post
are those the new part numbers Monty?
Yep
houston is offline  
Reply With Quote
Old 03-12-2016, 11:12 PM
  #72  
Tech Master
iTrader: (17)
 
hookem34's Avatar
 
Join Date: Dec 2009
Location: Texas.....Y'all!
Posts: 1,793
Trader Rating: 17 (100%+)
Default

Monty what's the scoop on the TKI4? Game changer or upgrade?

Congrats on the DNC showing!
hookem34 is offline  
Reply With Quote
Old 03-13-2016, 12:08 AM
  #73  
Tech Prophet
iTrader: (95)
 
houston's Avatar
 
Join Date: Sep 2004
Location: Sherwood,OR
Posts: 15,743
Trader Rating: 95 (100%+)
Default

Originally Posted by hookem34 View Post
Monty what's the scoop on the TKI4? Game changer or upgrade?

Congrats on the DNC showing!
Havent ran parts bro

Only 2 kits in US as of today
houston is offline  
Reply With Quote
Old 03-13-2016, 01:25 AM
  #74  
Tech Fanatic
iTrader: (46)
 
mourinho's Avatar
 
Join Date: Jun 2013
Posts: 965
Trader Rating: 46 (100%+)
Default

Originally Posted by Andyg01 View Post
Might be two versions

KYOSHO INFERNO MP9 TKI4 SP (w/IFW461)
BRAND: KYOSHO
PART NUMBER: K.33001BSP

and without

Kyosho Inferno MP9 TKI4
BRAND: KYOSHO
PART NUMBER: K.33001B
one is just the kit, the other includes the recently announced 19 degree aluminium c-hubs which should work well with the reduced front kick up.

"special pack with the Kyosho Inferno MP9 TKI4 + Inferno MP9 (19DEG) Aluminium IFW461"



mourinho is offline  
Reply With Quote
Old 03-13-2016, 02:53 PM
  #75  
Tech Champion
 
Pulse_'s Avatar
 
Join Date: May 2010
Location: Brussels, Belgium
Posts: 5,081
Default

there are two versions of the TKI4 in Europe aswell, including the 19 c-hubs or not

availability: mid-april

price: 650€ without the optional 19 c-hubs or 700€ with it

french shops where the kit is available in pre-order: wartelle-shop, rcteam, winnersmodelisme, pcmshop

I'm very curious about the handling compared to the TKI3. Changes are small but the overall result on the car could be bigger than expected.
Pulse_ is offline  
Reply With Quote

Thread Tools
Search this Thread

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service