Go Back  R/C Tech Forums > General Forums > Nitro Off-Road
Kyosho Inferno MP9 TKI4 1/8 Buggy Kit >

Kyosho Inferno MP9 TKI4 1/8 Buggy Kit

Like Tree314Likes

Kyosho Inferno MP9 TKI4 1/8 Buggy Kit

    Hide Wikipost
Old 11-05-2018, 09:06 AM   -   Wikipost
R/C Tech ForumsThread Wiki: Kyosho Inferno MP9 TKI4 1/8 Buggy Kit
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: 30Tooth
Picked up a TKI3 and want to upgrade to TKI4 ? Here are all the updated parts:

Shocks

IF347-155 1.5X5 Pistons
IF471-01 Front Shock Body
IF470-01 Rear Shock Body
IF470-03BK Shock Adjust Dial
IFW154 Boots
IF346-05C Shock End Set

Wing

IF491BK Wing
IFW460B Wing Mount/Stay

Rear End

IFH006W Wheel
IF490 HUB
IF490-01 Hub Insert
IF492 Shock Pin
IF423HB Rear Arm
IF287 Hard Upper Rod Rear

Front End

IF489 Steering Rod Set
IF488 Knuckles
IF487H Front Arm
IFW458 Hard Lower Pin
IFW425 93MM CVD
IF286 Hard Upper Rod
IF486 Lower Susp Holder
IFW459 Servo Saver (Hard)
IF446B Ackerman Arm
IF426-64.5 Susp Shaft


Other

IF469B Filter
97035LW-13 Clutch Bell
IF453B Body Mount
IFW107GM Hexes
W300910 Washer
IF443B Center Diff Plate
IF444C Tank
IF479B Radio Box
96772 13x16x0.15mm Shim
IF481B Fuel Tank Stay
IFW336GM Wheelnut
IFB008 TKI4 Body
IFD403W TKI4 Decal

---------------------------

Another option if you want TKI4 Durability but TKI3 geometry of the front arm is :

IF493 Front Arm (Updated MP9 front arms replaces IF427B as a direct fit. Left and right.)

They use the older TKI3 captured outer hinge pin and screw. But if you just reem out the the outer hole you can use TKI hinge-pin/nut (IFW458)
---------------------------

Optional Updates / New Parts:

IFW469 IFW469 Aeration Cap Set(Threaded Big Shock/MP9)

IFW473 New Brake Pads (Sept 2017)

Optional Alu front hubs:
- IFW412 - 13 deg (like stock plastic ones)
- IFW436 - 16 deg
- IFW474 - 17.5 deg
- IFW461 - 19deg

M2C 1mm engine spacer: M2C9610

Body Options
New Bitty Force Body

Tebo's Build Videos

Video #1

Video #2

Video #3

Video #4

Video #5

Video #6

Original Kyosho MP9 TKI Thread
_____________________

Baseline setups from Joonas.




_____________________

Shock build with vented cap and compensator.

You have to use the HC diaphragms (if346-09,stock TKI3 and if not mistaken TKI4 too, yes the thin ones no one likes), aeration caps without the bleeder screw or mod the stock caps by drilling a 1.5 or 2mm hole on the top facing up or at an angle (doesn't matter the size or angle, it just for bleeding pressure behind the diaphragm and allow the foam compensator to breathe) and a 10mm width x 3.5mm height dome shaped foam compensator made from old open cell inserts or dishwasher sponge. The foam compensator has to be soft enough not to add rebound but allow the diaphragm to regain it's shape.

Setup Sheet and Tuning

The setup sheet is getting crowded with all options but don't worry once you get acquainted with the parts will make sense.
Run the car as is, more than probably you won't need anything else. Using my setup as an example:

Diff gear has two options, normal and LSD. LSD stands for limited slip differential and is like using thick oils because you can't tune coast from locked.

Shock setup is a bit more confusing, you have two shock body sizes (S and M and truggy sized rear shocks that only the first version had so forget this one), three types of pistons (flat holes and surfaces, flat holes tapered surface and tapered holes with tapered surface): tapered have most pack, then black(simple piston) and then white because length of the holes. Then you have different length springs to account for different shock sizes, for a standard wheelbase/no weights car a good combo is Light Blue front and Orange rear, if you extend the wheelbase then I expect the included Light Blue rear springs be money instead of Orange.

Ride height is self explanatory, start always with lower arms parallel because good suspension geometry will be far easier to achieve. Rebound is used as total shock length no idea why they call it rebound, either use total shock length or maximum exposed shock shaft length. Camber self explanatory, run more camber in the front than the rear to make the car oversteer and more rear than front to make it understeer(grossly oversimplified).

Toe same deal as camber(again grossly oversimplified) but this you have to run the least amount you can. I use around 2-2.5 on my cars, never more as I can find traction by other means with way less impact on performance.

Wheelbase is a powerful setting, changes a lot of stuff. Let's just say that it can make the car behave neutral or not in that small range. Try for yourself. I like to use the longest setting and tune from there.

Shock position self explanatory, something most don't change and I don't play around with it. I do have a method but involves much work (with the car bottomed out, see which position places the shock 90 to the lower arm and then chose spring from a couple equations and bam done, I can do it easily so anyone interested just ask.

Rear upper arm position is again an important setting, you change both camber gain and roll centre. The rear roll centre should be higher than the front, that's why I use the middle hole inner row as a starting setup.

Suspension arm, self explanatory: there are two different length arms and each has a hard and a normal flex plastic.

Front suspension bushing is for upper arm alignment, also same deal as rear upper arm position changes both camber gain and roll centre.

Suspension holder is for kick up (pro dive is the correct naming). I believe tki4 9 of kick up to be better than 9 of kick up using the tki3 parts because you can run the car lower (26mm front ride height) and use the +2mm front shock tower if there's too much camber gain or it's stiff in roll. So use +2mm lowered roll centre to keep most stuff unchanged or use the bushings with the dot up to lower the roll centre a bit more, doesn't hurt anything.

Front hub carrier, self explanatory. I am trying to use the out hole on top of the carrier as it is better during braking and accelerating. Together with the higher front roll centre on the tki4 should provide enough camber gain during cornering if not then more caster will do.

Rear roll centre and anti squat(wrongly called skid angle). Again same thinking as the front, lower the car and keep roll centre in the same height as before(that will need a change in upper arm position which my setup does). Anti squat is changed only if the pitching motion causes too much camber to be gained by the rear tires on power, nothing more.

Front knuckle, apparently there's a difference in the Ackerman arm. Can't say anything about them as I don't know enough about both.

Rear hub carrier,there is one made of plastic (which doesn't have offset apparently so it's suited to long arm setting) and three aluminium versions. One similar to the plastic one, other with offset and a new one with offset and adjustable hub height.

Rear tread can be used as arm length and outboard toe(never seen it being used but the possibility is there). Longer is better most of the time (only on really low traction).

Chassis brace, wheel hub, sway bars and weight are self explanatory. No need to use weights nor other hubs. A couple of roll bars would be a nice addition. About the aluminium braces I am torn, I guess the car doesn't need flex with this setup but won't recommend the stiffer braces but the lower engine mount is very nice to deal with flex around the clutch.

Wing and wing stay are like the d81x had regarding height and position. The wing should be as low and have free airflow as possible.

Print Wikipost

Old 07-09-2017, 09:15 PM
  #1741  
Tech Fanatic
 
vandalzzz's Avatar
 
Join Date: Jul 2013
Location: somewhere near Japan
Posts: 762
Default

Mine dirtiest race ever:
vandalzzz is offline  
Old 07-10-2017, 01:54 PM
  #1742  
Tech Elite
iTrader: (11)
 
1evo RRR Driver's Avatar
 
Join Date: Dec 2008
Posts: 2,613
Trader Rating: 11 (100%+)
Default

Originally Posted by vandalzzz
Mine dirtiest race ever:
Ouch!
1evo RRR Driver is offline  
Old 07-10-2017, 01:56 PM
  #1743  
Tech Fanatic
iTrader: (61)
 
Join Date: Feb 2010
Location: Chula Vista, CA
Posts: 985
Trader Rating: 61 (100%+)
Default

Wow. Do you race on a beach.
mr240 is offline  
Old 07-10-2017, 01:58 PM
  #1744  
Tech Elite
iTrader: (11)
 
1evo RRR Driver's Avatar
 
Join Date: Dec 2008
Posts: 2,613
Trader Rating: 11 (100%+)
Exclamation

Looks like the main started 5mins b4 a storm started!😳
1evo RRR Driver is offline  
Old 07-10-2017, 04:55 PM
  #1745  
Tech Master
iTrader: (21)
 
Join Date: Sep 2010
Location: So Cal
Posts: 1,953
Trader Rating: 21 (100%+)
Default

I noticed Tebo with holes drilled in his wing too recently. What's that doing for you? And what size drill?
rcmoe is offline  
Old 07-10-2017, 07:48 PM
  #1746  
Tech Fanatic
 
vandalzzz's Avatar
 
Join Date: Jul 2013
Location: somewhere near Japan
Posts: 762
Default

Originally Posted by rcmoe
I noticed Tebo with holes drilled in his wing too recently. What's that doing for you? And what size drill?
We have very windy weather this season, and holes in wing reduces parachute effect. W/o them not only jumps are unstable, but buggy can flip over during hard brake combined with a strong gust of wind.
They're around 8mm in dia, pre-drilled and reamed with a simple body reamer.
vandalzzz is offline  
Old 07-10-2017, 07:50 PM
  #1747  
Tech Fanatic
 
vandalzzz's Avatar
 
Join Date: Jul 2013
Location: somewhere near Japan
Posts: 762
Default

Originally Posted by 1evo RRR Driver
Looks like the main started 5mins b4 a storm started!😳
Nope, it was just a very damp, almost tropical-like mist
vandalzzz is offline  
Old 07-10-2017, 08:01 PM
  #1748  
Tech Fanatic
 
vandalzzz's Avatar
 
Join Date: Jul 2013
Location: somewhere near Japan
Posts: 762
Default

Another in-action shot:
Attached Thumbnails Kyosho Inferno MP9 TKI4 1/8 Buggy Kit-k080717.jpg  
vandalzzz is offline  
Old 07-13-2017, 08:31 AM
  #1749  
Tech Regular
iTrader: (22)
 
Join Date: Jul 2014
Posts: 478
Trader Rating: 22 (100%+)
Default

Anyone know what nose piece this is?
Attached Thumbnails Kyosho Inferno MP9 TKI4 1/8 Buggy Kit-img_6361.jpg  
NoobRacer is offline  
Old 07-13-2017, 12:00 PM
  #1750  
Tech Lord
iTrader: (359)
 
tobamiester's Avatar
 
Join Date: Jul 2009
Location: Tea drinking Limmey in NJ
Posts: 12,321
Trader Rating: 359 (100%+)
Default

Originally Posted by NoobRacer
Anyone know what nose piece this is?
https://www.prolineracing.com/images...ts/3456-17.jpg
tobamiester is offline  
Old 07-13-2017, 12:14 PM
  #1751  
Tech Fanatic
 
tom1974's Avatar
 
Join Date: Jan 2013
Location: la maddalena italy
Posts: 970
Default

PROCEDURA RIEMPIMENTO AMMORTIZZATORI AD EMULSIONE | Fabrizio Teghesi driver 1:8 buggy con Kyosho, Os engines, Mlc fuel, Aka tyres, FTTech, Efra tools, Max Airbrush, Dreamsticker.
tom1974 is offline  
Old 07-13-2017, 12:16 PM
  #1752  
Tech Fanatic
 
tom1974's Avatar
 
Join Date: Jan 2013
Location: la maddalena italy
Posts: 970
Default

https://youtu.be/C-h5b52WO5s
tom1974 is offline  
Old 07-13-2017, 12:48 PM
  #1753  
Tech Regular
iTrader: (22)
 
Join Date: Jul 2014
Posts: 478
Trader Rating: 22 (100%+)
Default

Thanks. So he just has a two piece body then. I was thinking it was a hard plastic of some sort.
NoobRacer is offline  
Old 07-15-2017, 06:15 AM
  #1754  
Tech Rookie
 
Join Date: Mar 2017
Location: Austria/Vienna
Posts: 16
Default

Does anyone add weight (FE) to the car?
Chris_Sponge is offline  
Old 07-15-2017, 11:10 AM
  #1755  
Tech Master
iTrader: (21)
 
Join Date: Sep 2010
Location: So Cal
Posts: 1,953
Trader Rating: 21 (100%+)
Default

I run 20g in the front and 10 in the rear
rcmoe is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell or Share My Personal Information -

Copyright © 2023 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.