Go Back  R/C Tech Forums > General Forums > Nitro Off-Road
Kyosho Inferno MP9 TKI4 1/8 Buggy Kit >

Kyosho Inferno MP9 TKI4 1/8 Buggy Kit

Like Tree314Likes

Kyosho Inferno MP9 TKI4 1/8 Buggy Kit

    Hide Wikipost
Old 11-05-2018, 09:06 AM   -   Wikipost
R/C Tech ForumsThread Wiki: Kyosho Inferno MP9 TKI4 1/8 Buggy Kit
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: 30Tooth
Picked up a TKI3 and want to upgrade to TKI4 ? Here are all the updated parts:

Shocks

IF347-155 1.5X5 Pistons
IF471-01 Front Shock Body
IF470-01 Rear Shock Body
IF470-03BK Shock Adjust Dial
IFW154 Boots
IF346-05C Shock End Set

Wing

IF491BK Wing
IFW460B Wing Mount/Stay

Rear End

IFH006W Wheel
IF490 HUB
IF490-01 Hub Insert
IF492 Shock Pin
IF423HB Rear Arm
IF287 Hard Upper Rod Rear

Front End

IF489 Steering Rod Set
IF488 Knuckles
IF487H Front Arm
IFW458 Hard Lower Pin
IFW425 93MM CVD
IF286 Hard Upper Rod
IF486 Lower Susp Holder
IFW459 Servo Saver (Hard)
IF446B Ackerman Arm
IF426-64.5 Susp Shaft


Other

IF469B Filter
97035LW-13 Clutch Bell
IF453B Body Mount
IFW107GM Hexes
W300910 Washer
IF443B Center Diff Plate
IF444C Tank
IF479B Radio Box
96772 13x16x0.15mm Shim
IF481B Fuel Tank Stay
IFW336GM Wheelnut
IFB008 TKI4 Body
IFD403W TKI4 Decal

---------------------------

Another option if you want TKI4 Durability but TKI3 geometry of the front arm is :

IF493 Front Arm (Updated MP9 front arms replaces IF427B as a direct fit. Left and right.)

They use the older TKI3 captured outer hinge pin and screw. But if you just reem out the the outer hole you can use TKI hinge-pin/nut (IFW458)
---------------------------

Optional Updates / New Parts:

IFW469 IFW469 Aeration Cap Set(Threaded Big Shock/MP9)

IFW473 New Brake Pads (Sept 2017)

Optional Alu front hubs:
- IFW412 - 13 deg (like stock plastic ones)
- IFW436 - 16 deg
- IFW474 - 17.5 deg
- IFW461 - 19deg

M2C 1mm engine spacer: M2C9610

Body Options
New Bitty Force Body

Tebo's Build Videos

Video #1

Video #2

Video #3

Video #4

Video #5

Video #6

Original Kyosho MP9 TKI Thread
_____________________

Baseline setups from Joonas.




_____________________

Shock build with vented cap and compensator.

You have to use the HC diaphragms (if346-09,stock TKI3 and if not mistaken TKI4 too, yes the thin ones no one likes), aeration caps without the bleeder screw or mod the stock caps by drilling a 1.5 or 2mm hole on the top facing up or at an angle (doesn't matter the size or angle, it just for bleeding pressure behind the diaphragm and allow the foam compensator to breathe) and a 10mm width x 3.5mm height dome shaped foam compensator made from old open cell inserts or dishwasher sponge. The foam compensator has to be soft enough not to add rebound but allow the diaphragm to regain it's shape.

Setup Sheet and Tuning

The setup sheet is getting crowded with all options but don't worry once you get acquainted with the parts will make sense.
Run the car as is, more than probably you won't need anything else. Using my setup as an example:

Diff gear has two options, normal and LSD. LSD stands for limited slip differential and is like using thick oils because you can't tune coast from locked.

Shock setup is a bit more confusing, you have two shock body sizes (S and M and truggy sized rear shocks that only the first version had so forget this one), three types of pistons (flat holes and surfaces, flat holes tapered surface and tapered holes with tapered surface): tapered have most pack, then black(simple piston) and then white because length of the holes. Then you have different length springs to account for different shock sizes, for a standard wheelbase/no weights car a good combo is Light Blue front and Orange rear, if you extend the wheelbase then I expect the included Light Blue rear springs be money instead of Orange.

Ride height is self explanatory, start always with lower arms parallel because good suspension geometry will be far easier to achieve. Rebound is used as total shock length no idea why they call it rebound, either use total shock length or maximum exposed shock shaft length. Camber self explanatory, run more camber in the front than the rear to make the car oversteer and more rear than front to make it understeer(grossly oversimplified).

Toe same deal as camber(again grossly oversimplified) but this you have to run the least amount you can. I use around 2-2.5 on my cars, never more as I can find traction by other means with way less impact on performance.

Wheelbase is a powerful setting, changes a lot of stuff. Let's just say that it can make the car behave neutral or not in that small range. Try for yourself. I like to use the longest setting and tune from there.

Shock position self explanatory, something most don't change and I don't play around with it. I do have a method but involves much work (with the car bottomed out, see which position places the shock 90 to the lower arm and then chose spring from a couple equations and bam done, I can do it easily so anyone interested just ask.

Rear upper arm position is again an important setting, you change both camber gain and roll centre. The rear roll centre should be higher than the front, that's why I use the middle hole inner row as a starting setup.

Suspension arm, self explanatory: there are two different length arms and each has a hard and a normal flex plastic.

Front suspension bushing is for upper arm alignment, also same deal as rear upper arm position changes both camber gain and roll centre.

Suspension holder is for kick up (pro dive is the correct naming). I believe tki4 9 of kick up to be better than 9 of kick up using the tki3 parts because you can run the car lower (26mm front ride height) and use the +2mm front shock tower if there's too much camber gain or it's stiff in roll. So use +2mm lowered roll centre to keep most stuff unchanged or use the bushings with the dot up to lower the roll centre a bit more, doesn't hurt anything.

Front hub carrier, self explanatory. I am trying to use the out hole on top of the carrier as it is better during braking and accelerating. Together with the higher front roll centre on the tki4 should provide enough camber gain during cornering if not then more caster will do.

Rear roll centre and anti squat(wrongly called skid angle). Again same thinking as the front, lower the car and keep roll centre in the same height as before(that will need a change in upper arm position which my setup does). Anti squat is changed only if the pitching motion causes too much camber to be gained by the rear tires on power, nothing more.

Front knuckle, apparently there's a difference in the Ackerman arm. Can't say anything about them as I don't know enough about both.

Rear hub carrier,there is one made of plastic (which doesn't have offset apparently so it's suited to long arm setting) and three aluminium versions. One similar to the plastic one, other with offset and a new one with offset and adjustable hub height.

Rear tread can be used as arm length and outboard toe(never seen it being used but the possibility is there). Longer is better most of the time (only on really low traction).

Chassis brace, wheel hub, sway bars and weight are self explanatory. No need to use weights nor other hubs. A couple of roll bars would be a nice addition. About the aluminium braces I am torn, I guess the car doesn't need flex with this setup but won't recommend the stiffer braces but the lower engine mount is very nice to deal with flex around the clutch.

Wing and wing stay are like the d81x had regarding height and position. The wing should be as low and have free airflow as possible.

Print Wikipost

Old 05-14-2017, 06:19 PM
  #1561  
Tech Master
iTrader: (46)
 
mourinho's Avatar
 
Join Date: Jun 2013
Posts: 1,003
Trader Rating: 46 (100%+)
Default

Originally Posted by exheliguy
Hey guys, I'm running a 48 tooth spur and a 14 bell. Is that to small ? Or should I go to a 15 or 16?
48/14 is a great combination, it all depends on what characteristics your after.

48/15 would likely rob too much torque and probably wouldn't fit either.

yuichi has shared photos of a 47t spur.
mourinho is offline  
Old 05-14-2017, 07:16 PM
  #1562  
Tech Regular
iTrader: (4)
 
exheliguy's Avatar
 
Join Date: Jun 2011
Location: Northern Canada
Posts: 265
Trader Rating: 4 (100%+)
Default

I just saw that about the 47. I'm running a Reds R7 and the power is amazing. Maybe I'll give a 15 shot and see how if feels. And if I go back to a 46. Then a 13 is recommended?
exheliguy is offline  
Old 05-15-2017, 07:13 AM
  #1563  
Tech Lord
iTrader: (359)
 
tobamiester's Avatar
 
Join Date: Jul 2009
Location: Tea drinking Limmey in NJ
Posts: 12,334
Trader Rating: 359 (100%+)
Default

Originally Posted by exheliguy
I just saw that about the 47. I'm running a Reds R7 and the power is amazing. Maybe I'll give a 15 shot and see how if feels. And if I go back to a 46. Then a 13 is recommended?
been running stock 46/13 pretty everywhere.
tobamiester is offline  
Old 05-16-2017, 02:39 AM
  #1564  
Tech Adept
 
Join Date: Oct 2014
Posts: 102
Default

Originally Posted by Apco1
Thanks. I'm not expecting it to be as durable as a solid arm car like the HB or Tekno. But improved durability is a good thing. At the end of the day I just want to own an Inferno before I get to old and crusty to enjoy this hobby.
This car is solid. I've been driving the Mugen and the losi (both very durabel), and i'm extremely satisfied with this car also.
ColourGhost is offline  
Old 05-16-2017, 09:01 AM
  #1565  
Tech Lord
iTrader: (359)
 
tobamiester's Avatar
 
Join Date: Jul 2009
Location: Tea drinking Limmey in NJ
Posts: 12,334
Trader Rating: 359 (100%+)
Default

Originally Posted by ColourGhost
This car is solid. I've been driving the Mugen and the losi (both very durabel), and i'm extremely satisfied with this car also.
Love to see positive posts on here Cheers!
tobamiester is offline  
Old 05-16-2017, 09:54 AM
  #1566  
Tech Addict
iTrader: (2)
 
Apco1's Avatar
 
Join Date: Apr 2013
Location: Tx
Posts: 618
Trader Rating: 2 (100%+)
Default

Originally Posted by ColourGhost
This car is solid. I've been driving the Mugen and the losi (both very durabel), and i'm extremely satisfied with this car also.
Thanks. Just waiting for tower to get them back in stock.
Apco1 is offline  
Old 05-17-2017, 03:56 AM
  #1567  
Tech Adept
 
Join Date: Feb 2011
Posts: 199
Default

Hey guys, Here is a spot were you can get some 2.9mm pins for your unis. These dudes are cool & ship fast. https://www.rc-tworks.com/collection...3-8mm-pin-6pcs
gerry6112 likes this.
kyosho28 is offline  
Old 05-17-2017, 09:37 AM
  #1568  
Tech Apprentice
 
marmittone's Avatar
 
Join Date: Jun 2010
Location: South Italy
Posts: 81
Default

Hey guys, what pin remover do you use?
marmittone is offline  
Old 05-17-2017, 10:12 AM
  #1569  
Tech Addict
iTrader: (17)
 
pl_unc86's Avatar
 
Join Date: Oct 2007
Posts: 554
Trader Rating: 17 (100%+)
Default

Anyone have oil leak from the center diff? I noticed some oil on both the ebuggy and nitro running out of the center diff.

I never really knew how high to fill them since the manual is like reading a map drawn in the sand.

These are brand new kits, neither have touched the track, only some running in the street for break in.
pl_unc86 is offline  
Old 05-17-2017, 11:33 AM
  #1570  
Tech Lord
iTrader: (359)
 
tobamiester's Avatar
 
Join Date: Jul 2009
Location: Tea drinking Limmey in NJ
Posts: 12,334
Trader Rating: 359 (100%+)
Default

Originally Posted by marmittone
Hey guys, what pin remover do you use?
Get the Mugen one. Much dialedness...
CFRacing likes this.
tobamiester is offline  
Old 05-17-2017, 12:37 PM
  #1571  
Tech Rookie
 
Join Date: Mar 2017
Location: Austria/Vienna
Posts: 16
Default

Originally Posted by pl_unc86
Anyone have oil leak from the center diff? I noticed some oil on both the ebuggy and nitro running out of the center diff.

I never really knew how high to fill them since the manual is like reading a map drawn in the sand.

These are brand new kits, neither have touched the track, only some running in the street for break in.
I have the same problem but i think i use to much oil.
Go to youtube and search for: How to build a Kyosho MP9 diff with Jared Tebo

Maybe it is helpfull for you
Chris_Sponge is offline  
Old 05-17-2017, 01:29 PM
  #1572  
Tech Adept
 
Join Date: Oct 2014
Posts: 102
Default

Originally Posted by kyosho28
Hey guys, Here is a spot were you can get some 2.9mm pins for your unis. These dudes are cool & ship fast. https://www.rc-tworks.com/collection...3-8mm-pin-6pcs
Really nice info - thanks. Just ordered
ColourGhost is offline  
Old 05-17-2017, 03:15 PM
  #1573  
Tech Master
iTrader: (46)
 
mourinho's Avatar
 
Join Date: Jun 2013
Posts: 1,003
Trader Rating: 46 (100%+)
Default

Originally Posted by pl_unc86
Anyone have oil leak from the center diff? I noticed some oil on both the ebuggy and nitro running out of the center diff.

I never really knew how high to fill them since the manual is like reading a map drawn in the sand.

These are brand new kits, neither have touched the track, only some running in the street for break in.
apply grease liberally to the outdrive, diff cup seat, crown gear seat, o-ring and gasket.
use a thick grease.
build diff and place on a fine electronic scale, fill front and rear with 2.4g silicon fluid and centre with 4.2g.
built like this they will never leak
CFRacing likes this.
mourinho is offline  
Old 05-17-2017, 05:52 PM
  #1574  
Tech Prophet
iTrader: (96)
 
houston's Avatar
 
Join Date: Sep 2004
Location: Sherwood,OR
Posts: 15,844
Trader Rating: 96 (100%+)
Default

Originally Posted by exheliguy
Hey guys, I'm running a 48 tooth spur and a 14 bell. Is that to small ? Or should I go to a 15 or 16?
14/48 is a great setup ... more legs on the straights ... minor torque loss but controls wheelspin .... i personally run 14/46 and will never switch ... more runtime and on the engine i use more torque in the form of usable power ....
exheliguy likes this.
houston is offline  
Old 05-17-2017, 07:15 PM
  #1575  
Tech Elite
iTrader: (89)
 
Motorman007's Avatar
 
Join Date: Dec 2003
Posts: 3,420
Trader Rating: 89 (100%+)
Default

Originally Posted by houston
14/48 is a great setup ... more legs on the straights ... minor torque loss but controls wheelspin .... i personally run 14/46 and will never switch ... more runtime and on the engine i use more torque in the form of usable power ....
Everywhere?
Motorman007 is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell or Share My Personal Information -

Copyright © 2023 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.