Go Back  R/C Tech Forums > General Forums > Nitro Off-Road
Clutch problem, HELP!  O.S. CV-R .18 >

Clutch problem, HELP! O.S. CV-R .18

Clutch problem, HELP! O.S. CV-R .18

Old 07-23-2010, 06:57 PM
  #1  
Tech Adept
Thread Starter
 
Join Date: Mar 2010
Location: FL
Posts: 181
Questions?? Clutch problem, HELP! O.S. CV-R .18

I sat down to replace my Kyosho motor with my shiny new O.S. CV-R .18, and SNAP the shafts are different diameters (5mm O.S., 7mm Kyosho) and the Kyosho clutch does not fit! I did not see that coming... The flywheel fits to the shaft via a compression collar. Does anyone know of an adapter to make the clutch fit this 5mm shaft? Or a different clutch that I can use?

In the image below, the left engine is the O.S. and engine on the right is the Kyosho:



EDIT --> I see that O.S. has a motor with a similar shaft, but it's got a rotary carb and my servo is set up for a slide carb. So I'm open to any solutions!

Last edited by MattFL; 07-23-2010 at 08:50 PM.
MattFL is offline  
Old 07-24-2010, 06:46 AM
  #2  
Tech Fanatic
iTrader: (6)
 
marshon50's Avatar
 
Join Date: May 2006
Posts: 898
Trader Rating: 6 (100%+)
Default

You'll probably get help if you post this in the Monster Truck forum....
marshon50 is offline  
Old 07-24-2010, 07:11 AM
  #3  
Tech Adept
Thread Starter
 
Join Date: Mar 2010
Location: FL
Posts: 181
Default

Thanks for the tip, I will try that forum too!
MattFL is offline  
Old 07-25-2010, 06:46 PM
  #4  
Tech Regular
iTrader: (19)
 
throttle-out's Avatar
 
Join Date: Aug 2007
Location: mount laurel
Posts: 427
Trader Rating: 19 (95%+)
Default

yep.
throttle-out is offline  
Old 07-27-2010, 03:37 AM
  #5  
Tech Regular
 
ramjesr's Avatar
 
Join Date: Jun 2010
Posts: 382
Default Help

Associated has several crankshaft adapters p/n's 7602 or #7604,#7603,#2312 You might have to cut the shaft with a special cutoff nut.
ramjesr is offline  
Old 07-27-2010, 06:51 AM
  #6  
Tech Initiate
iTrader: (1)
 
NitroFinatic93's Avatar
 
Join Date: Jul 2010
Posts: 48
Trader Rating: 1 (100%+)
Default

when i ran a OS 18 cv-rx in my t-maxx classic, i had to cut the shaft down and use an adapter. Also you can remove the rotary carb and install a slide type carb. The kyosho carb may fit, not exactly sure, i dont have any experience with them. If it doesn't your best bet would be to purchase a new slide type carb for it.
NitroFinatic93 is offline  

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.