R/C Tech Forums

R/C Tech Forums (https://www.rctech.net/forum/)
-   Nitro Off-Road (https://www.rctech.net/forum/nitro-off-road-130/)
-   -   losi 2.0 shock mod ? (https://www.rctech.net/forum/nitro-off-road/303832-losi-2-0-shock-mod.html)

PIMP_9000 06-10-2009 09:59 PM

losi 2.0 shock mod ?
 
I have heard of guys doing a vent hole and using a piece of foam above the bladder. Is there an article or someone who has done this that can give me a couple of answers like drill size and vent location foam density and what not. thanks in advance

pballer2777 06-10-2009 10:13 PM

there was an artical inone of the recent mags but not sure which one. they said to use a #56 drill bit and to glue 2 shock orings together and put then between the bladder and cap. i was thinkin of doin this but just haven't gotten a chance.

zzmain 06-11-2009 08:15 AM

Does anyone know which mag and what month? Thanks

ABURTON 06-11-2009 09:56 AM

zzman..

I think I got it posted on the speed shop thread..

Let me go check..

Garet Jax 06-11-2009 01:21 PM


Originally Posted by pballer2777 (Post 5923405)
there was an artical inone of the recent mags but not sure which one. they said to use a #56 drill bit and to glue 2 shock orings together and put then between the bladder and cap. i was thinkin of doin this but just haven't gotten a chance.

What does this mod yield?

Jube 06-11-2009 01:37 PM


Originally Posted by Garet Jax (Post 5925842)
What does this mod yeild?

The ability to get full rebound out of the shocks consistantly i believe.

crazysavage 06-11-2009 02:18 PM

The shocks build up easier and more consistent rebound since all you have to do is fill to the rim, drop on the bladder and tighten down the cap slowly and let the excess oil flow away no pushing up on the shock shaft. On the track I can say that the truck will not bottom on anything, the suspension seems to react quicker to bumps and turns and I never have oil build up at the top of my shocks like I used to. I cut out small stop sign shapes of proline buggy tire inserts for the cussions, I didnt like the 2 o ring idea and every thing is staying clean and holding up well. No rebuilds for 3 races with 3 qual. and 15min main plus 30min of practice each time.

AaronLee 06-11-2009 02:51 PM

just found the details on the speed shop thread on this forums(offroad). I tried to copy and paste but not sure whats up..lol

It's on the last page.

Akhor 06-11-2009 03:26 PM


I thought I had posted it here but I could not find it. What I do, and this was shown to me by Adam Drake is the following:

Drill a small hole in the shock cap(on top) around the flat machined spot. This hole can be approx the same size as the hole on the side of the cap.

Take two shock o-rings and glue them together with ca glue. Glue the o-rings into the inside of the cap(center it) Fill your shocks up until about 1/16-1/8 inch from the top. Insert your bladder and make sure it is seated. Pressing lightly with your finger.

Once air bubbles escape install cap and you should have close to full rebound front and rear. What you do not want is for the shock to lock up before fully compressing, if so take a touch of oil out and repeat.

The more traction the less rebound you will run. The less traction, the more rebound. I think Adam recenly posted this as well. For the most part I always run 3/4- full rebound on all but the highest bite tracks.
Here is teh original..

malcnz 06-11-2009 05:42 PM

just to clarify:
when you glue the orings in side the cap do they need to be around the drilled hole ? and does the hole need to be drilled in centre of the cap as wouldnt that be hard to do or can it be off centre? pics would be great:nod:
Thanks.

ABURTON 06-11-2009 06:04 PM

Just don't block the hole with the o-rings, they need to be in the center as they support the bladder.

At the top of your shock cap you will see that milled area that allows you to get the nut driver on easily it starts out small and goes wider. Just drill the small hole half way up that.

I'll try to take some pics Friday morning for ya!

PIMP_9000 06-11-2009 07:12 PM

looking forward to it. Thanks for all the help you guys.

Poinas2 06-12-2009 03:05 AM

So you don't have to be worried aboutr the dirt to build up in the shock bladder ? Also what would that 56 hole be in metric ? 1.3mm or 1.4mm or what ?

br
-mj

BIG RE 06-12-2009 03:29 PM

is anyone trying this with plastic caps? I don't want to mod $30 caps if I don't like it.

Jason-149 06-13-2009 05:03 PM

does anybody have pictures of this mod yet? I just recieved my new 2.0 roller today and i think it already has it done. it's a very small hole on the outer edge of the shock cap?


All times are GMT -7. It is currently 04:43 AM.

Powered By: vBulletin v3.9.3.6
Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.