Go Back  R/C Tech Forums > General Forums > Nitro Off-Road
need opinions. Please advise. >

need opinions. Please advise.

need opinions. Please advise.

Old 05-04-2009, 07:53 AM
  #1  
Tech Elite
Thread Starter
iTrader: (5)
 
Join Date: Mar 2009
Posts: 3,660
Trader Rating: 5 (100%+)
Default need opinions. Please advise.

I just finished breaking in my new os vspec. Well i was running it yesterday and it had rained and quit. I was tunning it down and it rained earlier. well i hit a big puddle of water (like a dumbass) and imediatley the engine cut out and went cold. I then took the air filter off and flushed the engine with fuel and restarted it ( started right up) got it back up to temp and shut it down to cool properly. Later i disassembled the engine, cleaned and flushed every piece of with wd40, cleaned all the deposits out. reassembled flushed with nitro and coated it real well with after run oil. My engine still has tons of compression, no parts look stressed (from cooling off to quickly) and actually is a tighter then before i cleaned it.


Is there anything i did wrong in this scenario??? I think in retrospect starting the engine back up was probably not the best idea, but it wasnt' that hot to begin with (200) And i was freaking out because it was alot of water.
dreaux is offline  
Old 05-04-2009, 08:01 AM
  #2  
Tech Elite
 
Join Date: Mar 2009
Location: Aurora, Colorado
Posts: 4,055
Default

What problems are you having with it. Hell if you can fire it up right now after the dip in the pool - you should be good. If you are having problems - post the issues....
token is offline  
Old 05-04-2009, 08:04 AM
  #3  
Tech Elite
iTrader: (16)
 
Trips's Avatar
 
Join Date: Aug 2001
Location: 360 Speedway
Posts: 2,251
Trader Rating: 16 (100%+)
Default

Nothing wrong with what you did, but not everything was really necessary. What I'd have done would have been to remove the glow plug, spin the engine with the starter or pull cord to clear any liquid out, put the plug back in and fire it up. After running for a bit, any residual water would be gone. After that, I'd have shut it down when I was done and put some after-run in.
Trips is offline  
Old 05-04-2009, 08:09 AM
  #4  
Tech Adept
iTrader: (3)
 
SuperSmoove's Avatar
 
Join Date: May 2009
Posts: 155
Trader Rating: 3 (100%+)
Default

You did more than i would have done. I would have just spun the water out with the plug out, and ran monkey snot through the motor, and let it sit for a while before restarting. Keep out of those puddles!
SuperSmoove is offline  
Old 05-04-2009, 08:27 AM
  #5  
Tech Master
iTrader: (67)
 
cary's Avatar
 
Join Date: Mar 2009
Location: NorCal
Posts: 1,914
Trader Rating: 67 (100%+)
Default

that the F is monkey snot
i have seen you say it befor
cary is offline  
Old 05-04-2009, 12:05 PM
  #6  
Tech Regular
iTrader: (7)
 
buckeye34's Avatar
 
Join Date: Jan 2008
Posts: 274
Trader Rating: 7 (100%+)
Default

"kinda" the same thing happened to me last summer at a proseries race. I was running down the back straight, hit a small crease in lane "just right" and the buggy went end over end, over barrier, turn marshal ducked, and the car ended up in a creek!!! took v-spec apart, used wd-40 all over, reassembled, left plug out and turned over on box for a few, installed new plug, ran like a dream! so, i do not think you hurt the engine at all...but just my story and my .02
buckeye34 is offline  
Old 05-04-2009, 02:59 PM
  #7  
Tech Addict
iTrader: (1)
 
Join Date: Feb 2009
Posts: 609
Trader Rating: 1 (100%+)
Default

I don't think you hurt it. I have seen engines suck water & hydrolock which bent the connecting rod but that would have been obvious.
romax is offline  
Old 05-04-2009, 04:30 PM
  #8  
Tech Adept
 
rc-mike's Avatar
 
Join Date: Feb 2009
Location: Dickson TN
Posts: 130
Default

I'd have just took the plug out and turned it over with the starter box to blow out any excess water and then put the plug back in and run it. I have had planes go in a pond before and just started them back up without problems. No, I don't fly that bad. I was trying float flying and the pond was too small to do a smooth landing so sometimes I flipped it.
rc-mike is offline  

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.