R/C Tech Forums - View Profile: silden
R/C Tech Forums

Go Back  R/C Tech Forums > Members List
Reload this Page >

silden's Profile

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

silden silden is offline

Tech Fanatic

Send Message
Last Activity: 04-02-2024 07:27 PM

About Me

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 04-02-2024 07:27 PM
  • Join Date: 12-18-2012
  • Referrals: 0

Social Profiles

Instant Messaging
Send an Instant Message to silden Using...
This Page
https://www.rctech.net/forum/members/silden-167013.html

Friends

Showing Friends 1 to 2 of 2

Visitor Messages

Showing Visitor Messages 1 to 1 of 1
  1. silden
    02-20-2013 08:01 PM - permalink
    .

Likes Received

97 Likes
  1. glennhl liked post by silden On thread : When to replace pan car springs?
    I had a fair amount of collapsed pan car springs. I would recommend to replace them when they are 1mm different in height(left to right). replace always both springs
    Liked On: 11-28-2023, 11:36 AM
    Posted On: 11-28-2023, 09:59 AM
  2. LonnyJ1950
    LonnyJ1950 liked post by silden On thread : 1/12 forum
    the coning comes from the camber. You need to either ad or remove camber depending where the coning is. aka add camber if the outside is smaller and reduce if the inside is smaller. We usually...
    Liked On: 07-23-2023, 03:52 PM
    Posted On: 07-23-2023, 01:27 PM
  3. LonnyJ1950
    LonnyJ1950 liked post by silden On thread : 1/12 forum
    We usually only balance the main chassis. the pod doesn’t make much difference balanced or not. the most important tuning is the tweak, rear axle is centered and free ball bearings on front and rear...
    Liked On: 03-03-2023, 06:36 PM
    Posted On: 03-03-2023, 12:27 PM
  4. RacinJ
    RacinJ liked post by silden On thread : 1/12 forum
    We usually only balance the main chassis. the pod doesn’t make much difference balanced or not. the most important tuning is the tweak, rear axle is centered and free ball bearings on front and rear...
    Liked On: 03-03-2023, 12:47 PM
    Posted On: 03-03-2023, 12:27 PM
  5. TOADYY
    TOADYY liked post by silden On thread : Pro 10: 235mm Le Mans Prototype Pan Car Discussion
    Per Randy we can run any 10.5. there are not many new style 10.5 motors approved and even less available on the market.
    Liked On: 09-22-2021, 08:02 PM
    Posted On: 09-22-2021, 07:58 PM
  6. phatboislim liked post by silden On thread : R1 Wurks brushless motors
    The stack is the stator stack where the wires are wound around. The regulations are allowing for a certain maximum and minimum length. A so called short stack is usually closer to the minimum...
    Liked On: 03-24-2021, 07:34 PM
    Posted On: 03-24-2021, 05:43 PM
  7. gigaplex
    gigaplex liked post by silden On thread : New LRP Flow Esc
    All sensored motors have a temp sensor. The X20 and 22 use the same sensor board. The X22 should work with the Flow and provide the correct temperature for read out. I hope this helps.
    Liked On: 03-07-2021, 08:45 PM
    Posted On: 03-07-2021, 08:44 PM
  8. Buckaroo
    Buckaroo liked post by silden On thread : 1/12 forum
    We’re using the Hobbywing 1S esc with great results.
    Liked On: 02-20-2020, 06:21 PM
    Posted On: 02-20-2020, 05:48 PM
  9. vafactor liked post by silden On thread : 1/12 forum
    We’re using the Hobbywing 1S esc with great results.
    Liked On: 02-20-2020, 06:04 PM
    Posted On: 02-20-2020, 05:48 PM
  10. antlockyer
    antlockyer liked post by silden On thread : 1/12 forum
    The Track we used to run on was quite small with a lot 180’s. Most tracks in the US run 1/12 mod open motor and blinky esc.
    Liked On: 01-29-2020, 12:28 PM
    Posted On: 01-29-2020, 11:32 AM
  11. simple
    simple liked post by silden On thread : 1/12 forum
    The language barrier was for sure an issue to properly understand the warning and rules. But on the other hand he and the whole team knew that he doesn’t speak any english and they should have take...
    Liked On: 01-15-2020, 10:17 AM
    Posted On: 01-15-2020, 09:48 AM
  12. two shoes
    two shoes liked post by silden On thread : 1/12 forum
    BTW. The DQ in A2 didn’t cost him the Worlds. It was the move on Michael right after the start and the tangle up after. He should have stayed calm and pick up the spot later on. Marc checked out...
    Liked On: 01-13-2020, 04:13 PM
    Posted On: 01-13-2020, 11:31 AM
  13. two shoes
    two shoes liked post by silden On thread : 1/12 forum
    Honestly everyone else got through tech without any issues. Therefore I’m not sure that the voltage was measured that close and if it was indeed that .05 Volt got him DQ. He should have checked the...
    Liked On: 01-13-2020, 04:12 PM
    Posted On: 01-13-2020, 10:23 AM
  14. LonnyJ1950
    LonnyJ1950 liked post by silden On thread : 1/12 forum
    BTW. The DQ in A2 didn’t cost him the Worlds. It was the move on Michael right after the start and the tangle up after. He should have stayed calm and pick up the spot later on. Marc checked out...
    Liked On: 01-13-2020, 01:41 PM
    Posted On: 01-13-2020, 11:31 AM
  15. Muddbutt69 liked post by silden On thread : 1/12 forum
    The play in the lower suspension ball and a collapsed spring can cause the difference. Can you measure the springs and try to remove the slop you mentioned. You need to add additional shims to have...
    Liked On: 12-29-2019, 10:10 PM
    Posted On: 12-29-2019, 07:13 PM
Page 1 of 7
1
2
3
Last »

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.