R/C Tech Forums - View Profile: NZDave
R/C Tech Forums

Go Back  R/C Tech Forums > Members List
Reload this Page >

NZDave's Profile

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

NZDave NZDave is offline

Tech Initiate

Last Activity: Today 02:00 AM

About Me

  • About NZDave
    Country of Residence
    NZ
    Gender
    Male

Statistics

Total Posts
General Information
  • Last Activity: Today 02:00 AM
  • Join Date: 09-14-2020
  • Referrals: 0

Likes Received

7 Likes
  1. kufman
    kufman liked post by NZDave On thread : The Homebuilt Dynamometer (Dyno)Thread!!!
    I built my dyno using information from Bob Wright and use his software (RC Crew Chief) to process it. Unfortunately Bob is no longer with us. The dyno uses an arduino uni that is read using Bob's...
    Liked On: 04-11-2024, 02:17 PM
    Posted On: 04-10-2024, 04:54 PM
  2. gigaplex
    gigaplex liked post by NZDave On thread : Tell me what to set my brushless motor timing to
    I've never had a motor rev slower with more timing on my dyno. Have only tested to about 60 degrees but this always gives higher revs that lower timings. I have only tested 21.5T and 13.5T motors as...
    Liked On: 03-18-2024, 06:35 PM
    Posted On: 03-18-2024, 05:32 PM
  3. Bsthetech
    Bsthetech liked post by NZDave On thread : USGT
    There are some funny dips in some of your torque curves. This seems to vary depending on what test you were doing but they seemed to be there for all 3 of the tests where they show. I have a home...
    Liked On: 07-12-2023, 10:00 AM
    Posted On: 07-11-2023, 10:38 PM
  4. MonkeyCmonkeyDo liked post by NZDave On thread : Panorama
    I love the body. It is a Schkee Can-Am car. It wasn't actually a closed cockpit car, the centre section above the cockpit was open. Origaninal was dayglo red.
    Liked On: 06-07-2023, 06:05 PM
    Posted On: 06-07-2023, 03:59 PM
  5. OffRoadJunkie
    OffRoadJunkie liked post by NZDave On thread : SkyRC Toro ESC's
    I run Toro 160A in one of my cars. I have had issues with the on board on/off switch. Fortunately I managed to source some more switches of the same dimensions and replace the faulty switch. I have...
    Liked On: 06-01-2023, 08:42 AM
    Posted On: 05-31-2023, 03:41 PM
  6. EDWARD2003
    EDWARD2003 liked post by NZDave On thread : RC Crew Chief Software
    This is very sad. I built my own dyno using Bob's information and he was very helpful when I was having issues. He will be missed. Dave
    Liked On: 05-17-2023, 05:39 PM
    Posted On: 05-15-2023, 01:48 AM
  7. jojji22 liked post by NZDave On thread : Arrowmax MM Center Pulley
    Try RCmart.com. I have a T4 with Arrowmax MM conversion and have got replacement pulleys from them. If it is the outer flange that has come off it is possible to machine up something to fit inside...
    Liked On: 05-13-2022, 04:13 AM
    Posted On: 05-12-2022, 03:12 PM

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.