Bmr4life
Tech Master
User Lists
- About Bmr4life
- Location
- Atlanta, GA
- Interests
- RC's
- Occupation
- Engineer
- Country of Residence
- US
- Gender
- Male
-
Signature
- Too many RC's to list.
Showing Visitor Messages 1 to 2 of 2
-
Hello Again, I have reconsidered my first offer. I will pay you 500.00 for the whole lot shipped to Arkansas. Again please send your paypal info so I can get you paid!
Thank You for your consideration of this offer. -
Hello, I am interested in the 2 MMM esc's and the 2, 2200 kv motors!
Would you do 400.00 them? If so please send your paypal info so I can pay you?
68 Likes
-
Bmr4life liked post by EMU On thread : Kyosho Mini-Z SeriesThe newer PN motors seem to have higher drag than the older ones that I am used to. Speculation is stronger magnets and higher brush tension, both of which increase the power of the motor. break...Liked On: 04-18-2019, 05:41 PM
Posted On: 04-18-2019, 05:37 PMBmr4life liked post by LJH On thread : RCP Mini 96 challengeGood call on direction, I did not even think about that. I will edit my original post. I am pressed for space as well, Plan A works fine, I am going to have to get creative for the others. ...Liked On: 04-17-2019, 06:23 PM
Posted On: 04-17-2019, 04:14 PMBmr4life liked post by LJH On thread : RCP Mini 96 challengeFor a small track it does take up a lot of room. I had a skiing accident a year ago that has left me paralyzed so I cannot get down to my basement so I set up the track in our living room and it...Liked On: 04-17-2019, 11:50 AM
Posted On: 04-17-2019, 08:14 AMBmr4life liked post by EMU On thread : Kyosho Mini-Z SeriesMore motor, will change the operating temperatures of the tire, and change how the traction of the surface reacts as well. You might need to break the motor in a bit by running it. Typically, the...Liked On: 04-16-2019, 05:54 PM
Posted On: 04-16-2019, 09:43 AMBmr4life liked post by LJH On thread : Kyosho Mini-Z SeriesOn the wheels make sure you are not tightening the wheel nuts to much. As for the motor mount you will have to do some trimming to get the motor wires to exit it smoothly. it will be quite clear...Liked On: 04-16-2019, 05:53 PM
Posted On: 04-16-2019, 07:01 AMBmr4life liked post by Pooch692000 On thread : RCP Mini 96 challengehave only run smooth side. So far my favorite combo is a toss up between pn km Softt rears with kyosho 20 front or the pn ksm super soft rears and soft fronts. Have a set Pn soft rears and...Liked On: 04-16-2019, 04:57 PM
Posted On: 04-16-2019, 02:15 PMBmr4life liked post by EMU On thread : RCP Mini 96 challengeWhile I have not used the smooth side on the mini-96, one local track (brooklyn hobbies) recently flipped their track. The layout is a bit different, but the fast lap is basically the same. The...Liked On: 04-16-2019, 04:56 PM
Posted On: 04-16-2019, 12:44 PMBmr4life liked post by Billy Kelly On thread : RCP Mini 96 challengethere’s about a second difference in lap times from rough to smooth. It takes awhile for the smooth side to develop traction.( I’ve got around 14,000 laps since Christmas when I changed sides ...Liked On: 04-16-2019, 11:18 AM
Posted On: 04-16-2019, 10:52 AMBmr4life liked post by LJH On thread : RCP Mini 96 challengeI am running both my SWB and LWB MR03's with Atomic 48T motors and they are perfect, I am geared pretty short so the motors have more to give but the run time is great. I have also been running my...Liked On: 04-16-2019, 11:17 AM
Posted On: 04-16-2019, 11:16 AMBmr4life liked post by Cameron Kellogg On thread : Kyosho Mini-Z SeriesWhich side of the RCP track are people racing on? I found on-line that the grooved side is the race and the smooth is the drift side, but not sure if that was a typo. Hard to tell by video's on-line...Liked On: 04-16-2019, 10:24 AM
Posted On: 05-06-2015, 01:29 PMBmr4life liked post by Billy Kelly On thread : **RCP Track material?**I’ve got those Harbor Feight mats. And I’ve got an RCP track ordered. They might be close, should know more tonight.Liked On: 04-15-2019, 05:53 PM
Posted On: 01-30-2018, 05:49 AMBmr4life liked post by EMU On thread : Kyosho Mini-Z SeriesYou can try sanding down the end of both plates closer to the axle .5mm and placing a small piece of paper on the other end to tighten up the mesh a little.Liked On: 04-12-2019, 09:18 AM
Posted On: 07-30-2018, 06:01 PMBmr4life liked post by userst On thread : Kyosho Mini-Z SeriesMy 6t pinion was used with the 6t motor end mounts, just as the car come assembled out of the box. Ideally I think the gear mesh should be about the thickness of a strip of paper. But in my case it...Liked On: 04-12-2019, 09:18 AM
Posted On: 07-30-2018, 05:55 PMBmr4life liked post by EMU On thread : Kyosho Mini-Z SeriesThanks for the kind words Mleemor. 7 and 8t pinions use the same plates. 6 and 9 have their own plates. I have always felt that the 8t pinion has the best mesh out of all of the stock pinions in...Liked On: 04-12-2019, 09:17 AM
Posted On: 07-30-2018, 04:11 PMBmr4life liked post by EbbTide On thread : Kyosho Mini-Z SeriesEssentially yes but you also have to take into account whether that body is for a narrow width car or a wide width car which the McLaren is. Also the wheel offsets should be taken into account since...Liked On: 04-12-2019, 09:09 AM
Posted On: 04-12-2019, 09:07 AM- Join Date
- 03-25-2009
- Total Posts
- 1,525
- Likes Received
- 59
- Likes Given
- 68
- iTrader
- Click Here
The last 10 visitor(s) to this page were:This page has had 2,616 visitsContact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.