R/C Tech Forums - View Profile: beebone
R/C Tech Forums

Go Back  R/C Tech Forums > Members List
Reload this Page >

beebone's Profile

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

beebone beebone is offline

Tech Addict

Last Activity: 10-22-2023 07:24 AM

About Me

  • About beebone
    Location
    Hong Kong
  • Signature
    GP: Capricorn C03 1/10 touring, Capricorn C803 1/8 onroad
    Engine: Tesla .12 WC, Tesla .21 7 port on-road, Rody VS02, OS 2101

Statistics

Total Posts
General Information
  • Last Activity: 10-22-2023 07:24 AM
  • Join Date: 01-30-2010
  • Referrals: 0

Likes Received

12 Likes
  1. VS_Rody
    VS_Rody liked post by beebone On thread : Rody VS Racing Engines - Onroad Motors
    I only run VS04 with original head shim with 25%, in both track TRC and ACO no additional 0.1mm shim is needed, the power band is more than enough and no need to over-tune the engine. I run Max...
    Liked On: 11-13-2019, 06:47 AM
    Posted On: 11-13-2019, 05:56 AM
  2. blackcloudracin liked post by beebone On thread : Serpent Cobra GT
    Buku GT clutch is another topic to learn, the bell inside can be mirror shine and the shoes are wearless. I also race 1/8 on road but it's different than Centax clutch
    Liked On: 07-18-2019, 12:30 PM
    Posted On: 06-28-2016, 02:50 AM
  3. VS_Rody
    VS_Rody liked post by beebone On thread : Rody VS Racing Engines - Onroad Motors
    So what about the run time? I remember OS .12 engine never enough 5 minutes run time.
    Liked On: 07-14-2018, 04:12 AM
    Posted On: 06-15-2017, 08:53 AM
  4. Houmb liked post by beebone On thread : Capricorn C803 1/8 On-road
    Follow the old Serpent guide to assemble the 2 speed, just close the spring with min tension, then set the set screw with minimal gap you can see between 2 shoes. Then adjust the spring until you...
    Liked On: 02-04-2018, 10:42 PM
    Posted On: 02-04-2018, 07:50 PM
  5. Houmb liked post by beebone On thread : Capricorn C803 1/8 On-road
    Yes I do! This car is under-weight, the side 16g brass won't affect the handling, only add the 15g brass cylinder if you need more oversteer. I also run with the 26g brass battery plate as well.
    Liked On: 01-31-2018, 12:33 AM
    Posted On: 01-30-2018, 06:17 AM
  6. Houmb liked post by beebone On thread : The new telsa 7 port
    Go for Tesla pipe. I used to use Hipex 2069 or 2115, the run time was over 5 mins but not very fast.
    Liked On: 12-28-2017, 10:08 PM
    Posted On: 12-28-2017, 07:47 PM
  7. snuvet75
    snuvet75 liked post by beebone On thread : Capricorn LAB C03 1/10th scale 200mm chassis
    Huge difference when using 6 holes engine mount with all 6 screws in, the rear end turn much faster in same setting with 4
    Liked On: 09-01-2017, 12:06 PM
    Posted On: 08-14-2017, 08:45 AM
  8. snuvet75
    snuvet75 liked post by beebone On thread : Capricorn LAB C03 1/10th scale 200mm chassis
    No, it fits both EVO or old chassis plate
    Liked On: 09-01-2017, 11:51 AM
    Posted On: 09-01-2017, 09:46 AM
  9. snuvet75
    snuvet75 liked post by beebone On thread : Capricorn LAB C03 1/10th scale 200mm chassis
    The 6 bolts firmly secure the mount to chassis, so less twist at the rear end it comes to more oversteer
    Liked On: 09-01-2017, 11:51 AM
    Posted On: 09-01-2017, 09:48 AM
  10. ibobi
    ibobi liked post by beebone On thread : Capricorn LAB C03 1/10th scale 200mm chassis
    Hi, Just assemble the C03 kit, I've found there is some misalign problem on front bulkhead, my procedure is, secure the L/R bulkheads, then secure the radio plate, then install the front shock...
    Liked On: 06-13-2017, 02:11 PM
    Posted On: 12-07-2016, 09:06 AM
  11. dan_vector
    dan_vector liked post by beebone On thread : Serpent 977 Viper
    My local track is bumpy and all of the EVO2 experienced this problem, heard there is a new design shaft coming out (but not yet confirm). Some of the local Serpent drivers report this issue. By...
    Liked On: 04-19-2017, 08:34 AM
    Posted On: 03-24-2017, 01:12 PM
  12. VS_Rody
    VS_Rody liked post by beebone On thread : Rody VS Racing Engines - Onroad Motors
    Rody did a good job on this engine, fuel consumption and torque are better than regular 2102. I'm very satisfy this engine.
    Liked On: 02-19-2017, 12:01 AM
    Posted On: 01-25-2017, 08:18 PM

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.