Casper

Tech Prophet

Last Activity: 12-07-2020 12:50 PM

About Me

About Casper

Location

Orange, Ca

Occupation

Mechanical Engineer
Signature
TLR/Losi Team Driver
TLR/Losi | Tekin | DE Racing | Spektrum | Exotek | JBRL | Kolor Koncepts | OC/RC |Sticky Kicks | Imagine It Graphics | Casper-RC.com
TLR 22 4.0 SR, TLR 22T 4.0, TLR 22-4 2.0, Spektrum DX6R

WWW.CASPER-RC.COM TLR and Tekin setups

Statistics

Total Posts

Total Posts: 17,869
Posts Per Day: 2.48
Find all posts by Casper
Find all threads started by Casper

Visitor Messages

Total Messages: 87
Most Recent Message: 04-12-2017 04:06 PM
Visitor Messages for Casper

General Information

Last Activity: 12-07-2020 12:50 PM
Join Date: 08-03-2004
Referrals: 3

Friends

Showing Friends 1 to 10 of 30

- $Tmoney$
- Tech Master
- 1badgoat
- Tech Regular
- A-32 XXX-SCT
- Tech Rookie
- bnj325
- Tech Regular
- Chris_RJ_Hurst
- Tech Rookie
- dmolina15
- Tech Fanatic
- elecRC23
- Tech Addict
- e_lu_sive1
- Tech Regular
- fastchevyboy
- Tech Fanatic
- glock man
- Tech Apprentice

Page 1 of 3

Visitor Messages

Showing Visitor Messages 1 to 10 of 87

04-12-2017 04:06 PM - permalink

bubbaslash

Hi Casper. There's a thread "been out for a while and have some questions". Someone was asking about parts compatibility between his MIP 10SCTE and the 3.0. I'm not knowledgeable about the new truck, and I thought you could help him since you've worked on the evolution of the truck over the years.
Thanks,
John
- View Conversation
08-17-2016 12:06 PM - permalink

Kass

Casper. Im a bit nee to 17.5 buggy and just bought an exotek alum 22 2.0 with a 3 gear. Can u plz give me a setup for indoor clay high bite? Thank u
- View Conversation
04-16-2014 08:46 AM - permalink

Casper

I would go with the std Dunford setup as a great base for the SCTE 1.0.

http://www.losi.com/ProdInfo/Files/L...ford-02_12.pdf

Motor Sensored start much better. Depending on how serious your racing is it may not matter all that much to you. I strongly believe in Tekin motors and ESC's but they are not the cheapest options. Guys have had good luck with the hobby wing stuff but you don't get the support with those if you do have an issue. There are lots of options out there.
04-16-2014 06:28 AM - permalink

Mike1977

hello I am looking to get back in the racing I have a scte the original.

I mainly like to run on dirt track I have a small 80x40 track at my house.. also looking to go to offroad dirt tracks some are big some are small. I'm not looking to change the whole car around every track just looking for a good base setup.

#1 on my diff fluids what is a good all around out door dirt set up?
#2 same question but for the shocks
#3 as of now I have a castle mamba max pro with the 3800 4 pole motor which seemed ok back when I was into it. I need a motor for another car which I could use the 3800 in that and get a new one for the scte truck what would you recommend as a inexpensive motor? is the sensered motors that much better?
basically I'm trying go over the whole truck once since it has been sitting and I know its needs attention.
thanks for any info you can give me.
Mike
- View Conversation
04-08-2014 10:45 AM - permalink

Casper

The bearings can be very tight on the case. keep pressing but trying to only push on the inner race if you can. They will go on.
04-07-2014 09:22 PM - permalink

Kaw1000

I'm trying to rebuild diffs in a SCTE TEN. I bought the HD diff case. The problem is the bearings that go over out drives will not go all the way down diff case shaft. The diff will not fit in case because bearings off just a little...case number tlr332001 and outer bearings...12x18 losa6956 Thanks
- View Conversation
04-07-2014 02:42 PM - permalink

Casper

Sorry not sure what a 22T-R conversion is? Is that Rear motor?

My std Rear motor setup is on my web site. www.casper-rc.com For carpet I would work with a MM setup though.
04-07-2014 02:20 PM - permalink

timw60

Hello.
I am putting the 22T-R conversion on my truck.
What setup do you use for indoor clay med to high bite?

The setup I have is for carpet.

Thanks. Tim..
- View Conversation
03-24-2014 08:29 AM - permalink

Casper

Lots of setups here.
http://www.teamtekin.com/hotwire/esc...up-sheets.html
or what I run here
http://www.casper-rc.com/Tekin_Setups.htm
03-24-2014 06:26 AM - permalink

RustyRC

whats profile settings on gen1 esc for tekin pro4 4600? outdoor track
- View Conversation