joelt

HMAN - Would you happen to have LCG/BD rear ball studs (tall ones for the rear hub) in your inventory? If yes, could I get it from you Sat morning and replace it when PITSHOP BOSS arrives?

Found out kasi that I bent one of them in my LCG, besides a hinge pin. Didn't have any in stock because I didn't think that this could happen. No wonder the LCG had been handling weird all Saturday, even when I removed all the setup modifications that I did already - - - parang CGM ni ITIM.

ITIM - Handa na yung FERAL matched packs mo at yung bago mong set ng SOREX 40s. Mounted yung SOREX tires duon sa chrome rims na binigay ni KUPZ as per your request!!!! Btw, Tamiya sponge inserts ang dapat kong ilagay, di ba?

joelt

HMAN - Sila ROBO and FBJ were at the track yesterday to try out the new layout. Too bad I wasn't able to join them 'coz of my LCG's problem

MR SHIMS - Oo nga. Ang tulin nung pinang di-discharge mo na motor.

joelt

Eh alin naman para sa iyo ang mas matulin na motor, DC or Team Brood???

joelt

Ang lupit mo!!! Generic pala para sa iyo ang Trinity Epic Pro motors (Pro kung may dyno readings). Ganyan din naman yung gamit namin ni PITSHOP boss, ha. His had a 23k reading while mine had 21k!!!

tamiyaboy

san ppwede kumuha manual ng TLO1 tamiya? thanks

at kung may pics sana kayo ng steering assembly pa send..

pitshop

iTrader: (56)

BD SWEEPS THE MASTERSQUALIFYINGWARMUPS

STOCK MASTERS WARMUP

1 CHOLO PARAGAS - YOKE BD - EPIC 27
2 MIKE ANG - YOKE BD - EPIC 27
3 CARLO DIONISIO - MI2 - DC
4 MIKE DIONISIO - MI2 - DC
5 JOEL TINIO - YOKE LCG - EPIC 27
6 JON - MI2 - BROOD
7 JP CALIMBAS - MI2 - DC
8 SENNEN - DNF

MOD MASTERS WARMUP

1 JASON RODRIGUEZ - YOKE BD - REEDY
2 MIKE ANG - YOKE BD - TRINITY
3 GERRY SOLER - AE FTTC4 - ORION
4 RONALD ITIM - UNKNOWN CAR - ORION
5 SONNY YALUNG - AE FTTC4 - EPIC

see you guys this saturday at the official start of the Masters Qualifying!!!
Will post updated schedule soon!

joelt

Time to change your car!!!! . . . . . Ayaw na kasing kilalanin ito ng Family ah este Factory Sponsor mo eh.

ROBORAT

iTrader: (7)

jt: if you have the shorter yok ball studs, all you have to do is shim it up so that ends up the same hight as the long neck (silver) studs. that should solve your probelm while maintaing the same rear roll center as you would with the standard studs.

Fatboy Joe

Yes, thanks so much, the track was so clean and dust free. This is the 1st time that it was spic and span. Thanks for sweeping Joke lang po Pinapabayaan lang ng mga 'kano yang mga hapon na yan, sa sabado, iba na ang usapan, hehehehe, diba robo

Fatboy Joe

sorry, double post

rough512

iTrader: (12)

JT: I have an extra.

ROBORAT

iTrader: (7)

fbj: korek! laban yan sa sabado! practis ka ha! hehehe ... la akong oras maka-practis e. only ran one pack yesterday tapos umulan na! dunno kung makaka practice ako sa sabado.

pitshop: if you are gona change one thing in the layout, baka pwede mag suggest. actually, baka naman pareho din ang balak mo so will wait and see nalang on sat.

joelt

I tried doing this yesterday. Problem was that there was hardly any thread left when I tried it. . . . have to raise the ball stud kasi by about 2mm or more eh

Bahala na si at si sa Sat. . . . Ilabas sa garahe ang SDW para makahabol sa mga BD !!!!

joelt

Ayun naman pala eh!!! Don't tell me kakahuyin mo yung sa LCG mo, though?. . . . In any case, peram hanggang makakuha ako galing kay PITSHOP BOSS ng kapalit. . . . . Para nde na kailangang ilabas sa garahe si SDW.

ROBORAT

iTrader: (7)

jt: yup, mite be a problem with having enuff threads to screw in the studs nga. anyway, meron naman pala extra si rough eh ... since din naman nya ginagamit yung LCG nya. at least you can use those until mang has stocks.