R/C DIY stuff... Make it Yourself and save $$$ !!!
#1
R/C DIY stuff... Make it Yourself and save $$$ !!!
Hey Guys...
You may have seen this before, but what the Hell, DIY stuff is always good!!!
Here it Goes:
1. DIY Discharger using car relay!!!
http://www.schumacher.clara.net/discharger.htm
2. DIY Battery Equaliser (1)
http://www.schumacher.clara.net/equaliser.htm
3. DIY Battery Equaliser with LED (2)
http://www.schumacher.clara.net/leddisplay.htm
4. DIY Battery Low Indicator
http://www.uashem.com/pageid-134.html
5. DIY Discharger for Battery Packs
http://www.uashem.com/pageid-128.html
6. DIY Switching Power Supply made from PC power Supply
http://www.marcee.org/Articles/PCPowerSupply.htm
7. DIY Switching Power Supply made from PC power Supply (My Favorite)
http://web2.murraystate.edu/andy.bat...owersupply.htm
Disclaimer:
Bewarned!!!
As with modifying any Electrical, this is potentially dangerous that has the potential to kill you and or burn down the Structure you are in, and/or cause any number of disasters that may be attributed to working with Electricity, including death!!!
Do so at your own Risk!!!
ENJOY!!!
You may have seen this before, but what the Hell, DIY stuff is always good!!!
Here it Goes:
1. DIY Discharger using car relay!!!
http://www.schumacher.clara.net/discharger.htm
2. DIY Battery Equaliser (1)
http://www.schumacher.clara.net/equaliser.htm
3. DIY Battery Equaliser with LED (2)
http://www.schumacher.clara.net/leddisplay.htm
4. DIY Battery Low Indicator
http://www.uashem.com/pageid-134.html
5. DIY Discharger for Battery Packs
http://www.uashem.com/pageid-128.html
6. DIY Switching Power Supply made from PC power Supply
http://www.marcee.org/Articles/PCPowerSupply.htm
7. DIY Switching Power Supply made from PC power Supply (My Favorite)
http://web2.murraystate.edu/andy.bat...owersupply.htm
Disclaimer:
Bewarned!!!
As with modifying any Electrical, this is potentially dangerous that has the potential to kill you and or burn down the Structure you are in, and/or cause any number of disasters that may be attributed to working with Electricity, including death!!!
Do so at your own Risk!!!
ENJOY!!!
Last edited by kelfo; 08-31-2006 at 11:14 AM.
#2
Please Share some of your DIY ideas and designs!!!
Updated!!!
#3
Okay, since you asked so nicely...
Here's a centre transmission I scratch-built out of some cheap pinions, and spurs...
It's for a custom 1/10 rock crawler, still not finished.
source: http://www.bigbigplanet.com/rccars/slt/
Here's a centre transmission I scratch-built out of some cheap pinions, and spurs...
It's for a custom 1/10 rock crawler, still not finished.
source: http://www.bigbigplanet.com/rccars/slt/
#4
My custom wound armature (40 turn single) on the right, compared to a 23T on the left...
source: http://www.bigbigplanet.com/rccars/tricks
source: http://www.bigbigplanet.com/rccars/tricks
#5
I tried to "improve" upon a Tamiya Grasshopper at one point. It turned out quite ugly but I'll call it phase 1...
source: http://www.bigbigplanet.com/rccars/mantis/
source: http://www.bigbigplanet.com/rccars/mantis/
#6
Wah... Very Nice!!!
#7
Can somebody out there show us how DIY drift tires are made???
#9
Guest
Originally Posted by Danny Teh
RC DIY.......good and can save $$$ but try to attempt only on the mechanical side of it.......and not electrical because.........it will get you kill or seriously injure as the warning said.
Strictly for electrical engineer.....................
Strictly for electrical engineer.....................
#10
What harm can 7.2v DC bring? In fact by using a hobby knife to work on our models is at least 10 time more dangerous.
#12
Tech Champion
iTrader: (7)
Attempt to do anything simple.........wouldn't kill you.......that's for sure
What I am saying anything more complex might as well buy it off the shelf as g electrical would be too dangerous to attempt for those who even doesn't have the knowledge to do it.
By all means if those who can........
What I am saying anything more complex might as well buy it off the shelf as g electrical would be too dangerous to attempt for those who even doesn't have the knowledge to do it.
By all means if those who can........
#13
Speed Demon...
Awesome Work!!!
Do you have access to a Hobby Lathe and Miller???
Awesome Work!!!
Do you have access to a Hobby Lathe and Miller???
#14
Tech Master
iTrader: (3)
Kelfo,
Thank you for the compliments... unfortunately, I do not have the access to those machinery. I do it in a more conventional way... with cordless drill, super sharp drill bits, good metal saw, sharp files and few types of sand paper. Vice is also a must.
However, please take care of those alluminum dust... it's health hazard.
Thank you for the compliments... unfortunately, I do not have the access to those machinery. I do it in a more conventional way... with cordless drill, super sharp drill bits, good metal saw, sharp files and few types of sand paper. Vice is also a must.
However, please take care of those alluminum dust... it's health hazard.
#15
Speed Demon...
U got loads of talents man...
Did you add a Gear Reduction Unit to pull a Real Car???
U got loads of talents man...
Did you add a Gear Reduction Unit to pull a Real Car???