759LikesMugen MTC1
03-13-2018, 09:34 AM - Wikipost
|
|||
|
|||
|
Mugen MTC1 Wiki:
MTC1 Manual on the Mugen Web Site. Correction for the manual   The max/min tooth count of the spur and pinion combined. 64p = 127 to 164 total teeth  48p = 95 to 120 total teeth  People who have spare spur gears left over from other cars which they wish to use but can only utilize 2 of the 4 mounting holes, here's neat trick from MKAH to drill 2 more holes precisely in the spur gear: 1.Dismantle the Spur Holder and mount XRAY Spur with two screws.  2.If you have take a 3mm Top Setting Screw  3.Get the Top Screw in the first free thread to the Spur Holder from the other side until it touches the Spur a litle bit. Make the same with the second free Thread.  4.Dismantle Top set Srew an the two screws witch holds the Spur on the Holder. Now you see two marks absolutely central.  5. Take an 3mm Driller an Drill the holes at the marked places  6.Mount the Spur with the two old and two new holes on the Spur.  Spur Gears known to fit the gear holder with the correct hole pattern 1. Axon 2. Panaracer Upper front arm hinge pin set screw tip (or any of the kit set screws): When installing the set screw run the set screw in until you can see it come into the hinge pin gap. Back the screw out and make sure there is no flashing in the way and then the screw. Now slide the pin in and you should hit the pin and come to a dead stop. It will be a solid feel and not sloppy like it will not tighten which is caused by any loose plastic. Hara's Setup  Robert Pietsch's Latest Carpet Setup 
|
05-25-2019, 08:53 AM
#1501
Hallo if I want use motor 5.5 or 4.5t which pinion and crown I use?
05-25-2019, 09:08 AM
#1502
05-26-2019, 03:37 AM
#1503
Thanks the track is short.....smooth and use late tyres .the track is bitume liquid .
that should I have as spare parts ?
there are weak pieces or devices I need to do?
that should I have as spare parts ?
there are weak pieces or devices I need to do?
Last edited by tom1974; 05-26-2019 at 12:53 PM.
05-26-2019, 04:48 AM
#1504
Dove posso trovare il numero di codice corona 95t ..99t or 100t (pich 64)?
With pich 64 can i use pinion 48dp?
quanti denti hanno la corona originale?
With pich 64 can i use pinion 48dp?
quanti denti hanno la corona originale?
Last edited by tom1974; 05-26-2019 at 01:09 PM.
05-26-2019, 05:04 AM
#1505
the smaller the number, the harder the spring?
05-27-2019, 09:42 AM
#1506
arms and steering knuckles, extra sway bars (at least the 1.3 rear), maybe a set of belts just in case.
not sure anything on the car is weak, but of you hit something hard enough, something will likely break. Depending on what car you have (old front end or the new performance upgrade kit A2002 for the car), will determine what option parts you may want. If still using the old style front end, then making sure you have the one piece top deck is a must. You can either use the first gen top deck, or you can use the new top deck that comes with the performance upgrade kit, if you want to use the new pitch rod setup with a slight mod to the top deck to fit the old style front end parts. If you already have the performance upgrade kit on the car, then you don't need much else in option parts, aside front some of the option wheel hexes and maybe a belt tensioner. You could also get the fan mount if you don't have that too.
05-27-2019, 01:41 PM
#1509
someone has a picture to see how the belt tensioner is mounted?
can i find this part aftmarket?
can i find this part aftmarket?
05-28-2019, 06:30 AM
#1511
05-29-2019, 03:18 AM
#1514
Thanks
05-29-2019, 03:27 AM
#1515