NEW XRAY T2

Reply Subscribe

Thread Tools

Search this Thread

01-23-2006, 05:51 PM

#2161

lbckevin

Tech Champion

iTrader: (107)

Join Date: Jan 2003

Location: Orange County, CA

Posts: 5,731

Trader Rating: 107 (99%+)

I have not had any tweak issues with the car, but I am running rubber tire on a high bite track ( Socal Raceway).

Car has been good, only added Tamiya 6mm hexes to clear the shocks.

Kevin

Last edited by lbckevin; 01-24-2006 at 10:11 AM.

01-23-2006, 05:56 PM

#2162

Rob Phillips

Tech Master

iTrader: (6)

Join Date: Nov 2004

Location: Indianapolis / VA

Posts: 1,722

Trader Rating: 6 (100%+)

Wait until Melton get's his. We'll see him over in the corner with his knee wedged against the chassis.

TWEAK!!!!!

01-23-2006, 05:57 PM

#2163

Rob Phillips

Tech Master

iTrader: (6)

Join Date: Nov 2004

Location: Indianapolis / VA

Posts: 1,722

Trader Rating: 6 (100%+)

Q? what are hub clamps?

01-23-2006, 06:02 PM

#2164

cvt01

Tech Addict

iTrader: (2)

Join Date: Dec 2004

Location: MI

Posts: 574

Trader Rating: 2 (100%+)

Thats funny, if somebody take the time and read back in the forum, a lot of guys stated two months ago that the button head screw design is much better than the contersunk one from tweak point of view. Now we hear the opposite...
I don't know who is right and I don't even care but it means half of the people around dunno what they are talking about...

01-23-2006, 06:03 PM

#2165

Ill Factor

Tech Regular

iTrader: (2)

Join Date: Jan 2002

Location: Cali

Posts: 489

Trader Rating: 2 (100%+)

Quote:

Originally Posted by lbckevin

I have not had any tweak issues with the car, but I am running rubber tire on a high bite track ( Socal Raceway).

Car has been good, only added 6mm hub clamps to clear the shocks.

Kevin

Hey Kevin, where can I find some of them there hub clamps? Thanks

I assume you use these in replacement of the stock ones?

01-23-2006, 06:10 PM

#2166

HRCRACER123

Tech Fanatic

iTrader: (33)

Join Date: Apr 2005

Location: Long Island, New York

Posts: 819

Trader Rating: 33 (100%+)

Quote:

Originally Posted by Ill Factor

Hey Kevin, where can I find some of them there hub clamps? Thanks

I assume you use these in replacement of the stock ones?

I,m not kevin. But I am using Tamiya 6mm wheel hexes and they work mint!! It gives plenty of room for the front foams to clear the knuckles.

You can find them here..http://www2.towerhobbies.com/cgi-bin...?&I=LXDLV1&P=7

Oh crap.. my bad I just checked to see if they were in stock and they are not. I guess me and a bunch of other racers scooped them all up for the T2. I am sure you can find them elsewhere though. That just where I got mine from. I only ordered them about a week ago. I guess they went fast.

01-23-2006, 06:36 PM

#2167

CoryCraig

Tech Apprentice

Join Date: Mar 2002

Location: greenville,SC

Posts: 98

Trader Rating: 0

LMAO!! sorry brandon but after our discussion the other day on the phone, thats hilarious!

Quote:

Originally Posted by Rob Phillips

Wait until Melton get's his. We'll see him over in the corner with his knee wedged against the chassis.

TWEAK!!!!!

01-23-2006, 07:41 PM

#2168

HRCRACER123

Tech Fanatic

iTrader: (33)

Join Date: Apr 2005

Location: Long Island, New York

Posts: 819

Trader Rating: 33 (100%+)

Has anybody heard anything or do any testing to see if the diffrence in the rear toe-in is in the hubs or not?

01-23-2006, 08:13 PM

#2169

RC Infusion.com

Registered User

Join Date: Oct 2005

Posts: 61

Trader Rating: 0

Quote:

Originally Posted by Ill Factor

Hey Kevin, where can I find some of them there hub clamps? Thanks

I assume you use these in replacement of the stock ones?

Hi, sorry I'm not Kevin either but if it helps I carry the Barracuda ones, 6mm, a direct fit for the T2. Should have T2 parts up on the site in a week or two as well. http://www.rcinfusion.com/ProductLis...?CategoryID=17

Part #AH600R & #AH600B half way down. I have 3 sets of red and 3 blue left.

Rob

01-23-2006, 08:28 PM

#2170

Andy C

Tech Adept

Join Date: Sep 2004

Posts: 147

Trader Rating: 0

On the setup sheet for the inner akermann position does the 1 & 2 denote the position of the bearing or the tab on the bearing holder?

01-23-2006, 09:20 PM

#2171

litespeed-dom

Tech Elite

iTrader: (4)

Join Date: Oct 2002

Location: Beaverton, Oregon

Posts: 3,990

Trader Rating: 4 (100%+)

Does anyone knows where which hobby shop on the West Coast that has a T2 in stock? Looking for one.

TIA!

Dom

01-23-2006, 09:22 PM

#2172

stonedgti

Tech Addict

iTrader: (15)

Join Date: Jun 2003

Location: U.S.A.

Posts: 700

Trader Rating: 15 (100%+)

www.allspeedhobbies.com has 1 left

01-23-2006, 09:36 PM

#2173

Roger

Tech Elite

iTrader: (10)

Join Date: Feb 2003

Posts: 2,329

Trader Rating: 10 (100%+)

Quote:

Originally Posted by Juan Aveytia

Harshguy, is stockton going to have practice on sunday the 29th?

Yeah, is there practice on the 29th ???I'd like to go just to set-up the car in the stockton highbite carpet.

01-23-2006, 09:45 PM

#2174

syndr0me

Tech Lord

iTrader: (32)

Join Date: Dec 2004

Location: 5280 Raceway

Posts: 13,279

Trader Rating: 32 (100%+)

The delay on spare parts was announced before the car was available. Did you guys buy the car hoping they were just kidding? It seems silly to be angry when there was plenty of notice this was going to happen.

01-23-2006, 09:48 PM

#2175

SuperXRAY

Tech Rookie

Join Date: Jan 2006

Posts: 7

Trader Rating: 0

IMHO, that's a pretty lame response. It isn't anyone but XRAY's fault for not having parts, known to consumers or not. Anyways....

Andy C, the marking on the setup sheets and Virtual Setup Sheets are the TAB on the bearing holder, not the bearing itself.