Tamiya TB-Evolution III
#5896
Tech Regular
thanks alot ill give it a go
#5898
Originally posted by f1larry
does anyone make a titanium suspension shaft set for the EVO 3?
does anyone make a titanium suspension shaft set for the EVO 3?
#5899
Tech Initiate
I'm preparing for the LRP challenge and was trying to read an article about Surikarn's car during last years race. Could a German speaking person please help me with the translation of the following sentence: (especially the word senkrechte)
Surikarn setzte in den Finalläufen gelbe Stabis vorne und hinten ein, weisse Federn vorne und hinten und er verwendet eine senkrechte Dämpfer-Position.
Thanks!
Surikarn setzte in den Finalläufen gelbe Stabis vorne und hinten ein, weisse Federn vorne und hinten und er verwendet eine senkrechte Dämpfer-Position.
Thanks!
#5900
Tech Addict
senkrecht = perpendicularly, so I bet it means that he had his shocks on the most vertical position.
#5901
Originally posted by J-Racer
I'm preparing for the LRP challenge and was trying to read an article about Surikarn's car during last years race. Could a German speaking person please help me with the translation of the following sentence: (especially the word senkrechte)
Surikarn setzte in den Finalläufen gelbe Stabis vorne und hinten ein, weisse Federn vorne und hinten und er verwendet eine senkrechte Dämpfer-Position.
Thanks!
I'm preparing for the LRP challenge and was trying to read an article about Surikarn's car during last years race. Could a German speaking person please help me with the translation of the following sentence: (especially the word senkrechte)
Surikarn setzte in den Finalläufen gelbe Stabis vorne und hinten ein, weisse Federn vorne und hinten und er verwendet eine senkrechte Dämpfer-Position.
Thanks!
Re: Shocks: it doesn't actually say anything other than the shocks were in an upright position, so I guess it would be the most upright position.
Cheers, Mark.
#5902
Tech Initiate
Thanks, that's what I thought aswell.
Too bad I don't know what oil he used...
At least I've found more than enough setups to get a good starting one.
Hopefully the car will be bulletproof with the Jürgen one-way and the lightweight driveshaft!
Anybody else here going to the LRP challenge with an EVO III?
Too bad I don't know what oil he used...
At least I've found more than enough setups to get a good starting one.
Hopefully the car will be bulletproof with the Jürgen one-way and the lightweight driveshaft!
Anybody else here going to the LRP challenge with an EVO III?
#5903
Surikarn used Tamiya 500 oil all around. 3 hole pistons, 2 black O-rings in each shock.
Rear dampers in position number 4.
Rear dampers in position number 4.
#5904
Originally posted by f1larry
does anyone make a titanium suspension shaft set for the EVO 3?
does anyone make a titanium suspension shaft set for the EVO 3?
Of topic but sort of related: The TA04 flourine coated shaft set is a direct fit with the 415...kinda cool because I have a buku load of them in my pitbox
#5905
Originally posted by rtypec
Of topic but sort of related: The TA04 flourine coated shaft set is a direct fit with the 415...kinda cool because I have a buku load of them in my pitbox
Of topic but sort of related: The TA04 flourine coated shaft set is a direct fit with the 415...kinda cool because I have a buku load of them in my pitbox
#5906
Originally posted by rccarracer
Yeah, all the cars use the same TRF Shocks, so the shafts will be the same as well.
Yeah, all the cars use the same TRF Shocks, so the shafts will be the same as well.
#5907
Originally posted by jeffreylin
He meant shafts for the suspension, not for the shocks.
He meant shafts for the suspension, not for the shocks.
But thats good to hear as I also have a set or two around.
#5908
Hi Guys,
We got some new hop-ups in for the EVOIII including Ti-Axles, aluminum rear hubs, and light weight center shafts. Also a few new Tobee Craft hop-ups as well.
Lastly, we should be receiving the first batch of EVOIII Spools within the next few weeks.
Steve Wang
We got some new hop-ups in for the EVOIII including Ti-Axles, aluminum rear hubs, and light weight center shafts. Also a few new Tobee Craft hop-ups as well.
Lastly, we should be receiving the first batch of EVOIII Spools within the next few weeks.
Steve Wang
#5909
Tech Regular
steve, any idea what differences the tobee craft light weight shaft carries?
thanks
How are everyones Evo's, everythign seems quite recently
thanks
How are everyones Evo's, everythign seems quite recently
#5910
hey steve i was wondering is the tobbecracrft lightweight shaft the same length as the new tamiya lightweight shaft? so people dont strip there oneway ? evo uk people are quiet latelly i think it has something to do with the trf 415 .