R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

Reply
 
Thread Tools Search this Thread
Old 05-28-2005, 03:22 AM   #1
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default 2005 FEMCA 1/10TH ISTC ELECTRIC TOURING CAR CHAMPIONSHIP

2005 FEMCA ISTC - MALAYSIA



Event : 2005 FEMCA 1/10TH ISTC ELECTRIC TOURING CAR CHAMPIONSHIP

Location : "KOTA RAJA SPEEDWAY TRACK" Stadium Kota Raja, Klang. Selangor, Malaysia.

Date : Thursday, 8th December 2005 - Monday, 12th December, 2005 - (12th December - Rain Day)

Track : Outdoor Asphalt - track field size : 60m x 50m x 45m

Class : 1/10 ISTC Electric Touring Car 190mm

Entry Fee : USD $50.00 or MYR $190.00 Additional Banquet Dinner @ USD $12.00 or MYR $46.00

Entry Form : Request from your Country Association or download the E-Form. Please submit your entry form and fees to FEMCA representative in your country to reserve your seat for the event.

Organizer : RCMRC http://www.rcmrc.com Email : [email protected]

Website: http://www.rcmrc.com/istc/index.htm

Official Closing Date of Entry: 30 September 2005
After this date, a late entry fee of USD20.00 will be imposed. Malaysian Drivers will be given allocations and seat preferences after 30 October 2005.

Pre-FEMCA Race : Saturday, 6th & Sunday, 7 August 2005.
Open to all FEMCA drivers. Entries for this event would not need an entry form - drivers please send your details by email and Entry Fee of USD $13.00 or MYR $50.00 to be paid on the arrival to the track.

This event is open to all IFMAR Blocs i.e. drivers from FEMCA, EFRA, ROAR and FAMAR can compete at the event but the first FEMCA driver to finish will be the FEMCA Champion.

Last edited by aaronkhoo; 06-25-2005 at 11:06 PM.
aaronkhoo is offline   Reply With Quote
Old 05-29-2005, 11:47 PM   #2
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default FIRST EVER INTERNATIONAL EVENT IN MALAYSIA

2005 FEMCA 1/10TH ISTC ELECTRIC CHAMPIONSHIP

Dear Members

FEMCA member, Malaysia, has kindly offered to host the above event and it will be held at the Kota Raja Speedway, Klang, Malaysia from December 1-5, 2005. On behalf of all FEMCA members, I wish to thank the Malaysian Association, RCMRC for its willingness to host this event, the first FEMCA ISTC Championship.

A comprehensive Report and the entry form is attached. Please distribute it to all your members as soon as possible. Further details can be found on http://www.rcmrc.com

All entry forms and entry fees are to be forwarded to the drivers' national association. The national association is requested to forward the forms and fees to the organiser in Malaysia by the closing date of September 30, 2005.

N.B. Only drivers from countries who are current financial members of FEMCA can compete at the event and these drivers must be current financial members of their country's national Association.

At this time, only the following countries are financial members of FEMCA: Australia, China, Hong Kong, Indonesia, Japan, Malaysia, the Philippines, New Zealand, South Korea, Taiwan and Thailand.

In addition, because FEMCA Championships are run to IFMAR World Championship Rules, it will be necessary for FEMCA countries to select the controlled tyre and insert to be used at the FEMCA event. Please see Page 2. It is requested that your country's vote be returned to me by JUNE 30, 2005.

The IFMAR ISTC World Championship Rules can be found on http://www.ozemail.com.au/~ifmar

If you have any queries, please do not hesitate to contact me.

Best regards to all
John Grant cc FEMCA V.P.
President, FEMCA.
aaronkhoo is offline   Reply With Quote
Old 05-31-2005, 11:45 PM   #3
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default Sponsors, please apply early

If there are any Team, Manufacturer or Organization that wishes to be a sponsor for this event, please email us - [email protected].
Sponsors are to supply Banners, Prizes, T-shirts, Pit-Towels and any other promotional items.



What does "Kota Raja" Speedway means?
It means "City of Kings", KLANG - beautiful and peaceful, the centre of economic and social activities.Situated 32 km to the south-west of Kuala Lumpur, it is the main gateway into Malaysia by sea. This 75 square km. royal town of Selangor Darul Ehsan, is one of the oldest in Malaysia. The historical findings dated back to more than 2,000 years ago, prove that there has settlement in Klang since the iron and bronze age. Documents referring to this, from the Majapahit days, have also been found.

For centuries, until today the town has been the residence of His Highness Sultan of Selangor Darul Ehsan. The Selangor Darul Ehsan Sultanate started when the Sultan Sallehudin (Raja Lumu), who was the first Sultan of Selangor Darul Ehsan, set up the Malay Government 1643.



Klang river traverse itself from the Titiwangsa Range down to the heart of Kuala Lumpur city center and passing through the most populated part of Klang Valley. Here it is seen slowly reaching its downstream passing Klang town amidst the glittering light decorating both sides of the bridge. Building on the right is the Klang Municipal Council (MPK) building with their abbreviation sitting at the top of the structure.

Last edited by aaronkhoo; 06-05-2005 at 10:53 PM.
aaronkhoo is offline   Reply With Quote
Old 06-02-2005, 04:21 AM   #4
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default A little bit more about Klang town



2 June 2005, The Star Newspaper (Malaysia) – Boom town,Klang has come a long way since its early days as a merchants’ paradise. Today, it is still a bustling town, but the direction the royal town is …….

A part form being a royal town, Klang has always been a special and privileged place for Selangor as it has served as state capital from 1880 to 1977 before being replaced with Kuala Lumpur and later Shah Alam.

The early settlers, mostly Bugis, Javanese and Minangkabau origin, arrived in droves and lived in settlements along the Klang River. ….. Most of the early settlers were farmers, boatmen and fishermen. They sold their produce to traders from other parts of Malaya then and to merchants who pass through the Straits of Malacca.
aaronkhoo is offline   Reply With Quote
Old 06-02-2005, 06:09 AM   #5
Tech Adept
 
Join Date: Dec 2004
Location: Amsterdam
Posts: 140
Default

Sounds like a great race and nice country.... hope to be there!
Erik Jonk is offline   Reply With Quote
Old 06-04-2005, 12:25 AM   #6
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default RC HEADLINES at TEAM ORION Website

29 May 2005 - TEAM ORION - RC HEADLINES - FEMCA ISTC Championship


http://www.team-orion.ch/global/global_news.asp?id=2932
aaronkhoo is offline   Reply With Quote
Old 06-04-2005, 09:11 PM   #7
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default Another Newspaper write up about Klang Town

Hi Erik from Spintec, Yes, Malaysia is a very nice and peaceful country full of historical heritage for everyone to visit. Later we will update the website with more info on places to visit.


3 June 2005 - The Star Newspaper (Malaysia) - Port getting bigger, Port Klang has come a long way since the early days when it was still known as Port Sweetenham. The port, which used to be made up of two or three streets such as Camp Road and Watson Road and which housed four or five berths, has progressed steadily over the past 50 years. The old port, now known as South Port, was a popular destination of cargo and passenger vessels. It has since become Malaysia's premier port with its boundaries expanded to include North Port and West Port. The combination of all three ports has made Port Klang world class as it has also changed with the times.
aaronkhoo is offline   Reply With Quote
Old 06-05-2005, 10:23 AM   #8
Tech Master
 
Geetoo's Avatar
 
Join Date: Dec 2001
Location: HPI/HOTBODIES
Posts: 1,871
Trader Rating: 1 (100%+)
Send a message via AIM to Geetoo Send a message via Yahoo to Geetoo
Default

What classes are there? Mod and 23 turn stock right?
__________________
www.hpiracing.com
www.hotbodiesonline.net
www.nosram.com
www.team-durango.com
www.actionhobbiesonline.net
Geetoo is offline   Reply With Quote
Old 06-05-2005, 07:17 PM   #9
Tech Addict
 
Join Date: May 2005
Location: HKG
Posts: 638
Default

Do you have track layout photo ?
HKRCMODEL is offline   Reply With Quote
Old 06-05-2005, 11:52 PM   #10
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default More Sponsors will be joinning the FIRST FEMCA ISTC

Hi Geetoo,

2005 FEMCA ISTC will follow IFMAR Rules which is to run Open Modified. Log on to http://members.ozemail.com.au/~ifmar/rulesindpg.htm to get the latest IFMAR Rules & Regulations.

There are some updates on the Electric On-Road Technical Rules on Motor 4.3.2

BRUSHED MOTORS

Specifications: ‘05’ sized displacements..

Can diameter to be a maximum of 36.02mm

Can length to be maximum of 53mm measured from the mounting face of the motor to the furthest point not including solder, tabs or lead wires.

Shaft diameter is .125 inch. Production Tolerances allowed. Ceramic magnets only (cobalt and rare earth magnets specifically not allowed).

Current is supplied to the armature by two (2) brushes.

Armature - the rotor is to have three (3) poles with windings. Stack length without epoxy - minimum 21mm and maximum 28.8mm. Only copper wire is to be used for the winding.

No split rotor is allowed. The laminations have to be one after the other without anything between. The thickness of the stack plates is 0.35mm + 0.05mm, a maximum of sixty three (63) laminations to be used. The minimum stack thickness is 3.5mm.

A minimum of 5,000 units must be available at the time of approval. A minimum of three hundred (300) motors must have been sold to at least three (3) distributors or hobby shops or OEM ’s at the time of submittal.

The manufacturer has to provide an address of a hobby shop or the like, that any driver who wishes to obtain these motors at the time of approval can do so.

Approved motors may be modified by re-winding, balancing, truing of commutators, epoxying, ball bearings, brushes and custom brush systems only.

No hybrid (mixing of parts from approved motors) allowed.



Thanks
aaronkhoo is offline   Reply With Quote
Old 06-06-2005, 12:06 AM   #11
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default

Quote:
Originally Posted by HKRCMODEL
Do you have track layout photo ?
Hi HKRCMODEL,

The actual track layout will be available 2 Months prior to the event. Please take note that there will be a 60% change to the Track layout configuration at the start of the event.

There will also be new updates to the IFMAR Technical Rules, we will update everyone.

thanks


2.6 PRACTICE

2.6.1 There will be one day of practice (T-time, controlled practice) for each class. The track will not be available prior to commencement of each event.

2.6.2 Track layout must be at least 60% new in layout/design at the start of the event.

2.6.3 Practice will be organised using the „T-Time " format.. Under these arrangements the following parameters will be used:

a. Each segment will be restricted to 10 minutes (1/12) and 7 minutes (ISTC).

b. Drivers only to be allowed to sign up for „T-Time " practice..

c .A maximum of 15 cars to be allowed on the track during any one segment.

d. Drivers will only be allowed one frequency per segment.

e. The first "T-Time" practice will be allocated by the organisers..

2.6.4 All the IFMAR Technical Rules apply during Controlled Practice, including the use of batteries and motors from the IFMAR Approved List which have been checked (and marked where necessary) by Technical Inspection.
aaronkhoo is offline   Reply With Quote
Old 06-06-2005, 12:08 AM   #12
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default BRUSHLESS MOTOR ARE ALLOWED ! FOR 2005 FEMCA ISTC

There will be some serious competition on Brushed and Brushless for this coming meeting & event.

IFMAR TECHNICAL RULES - 4.3 MOTORS

BRUSHLESS MOTORS:

General definition of a Brushless Motor:

a) Sensored or sensorless motors are allowed.

b) The motor has to be rebuildable. Ball bearings are allowed.

c) If the motor is sensored:

- It must use a six position JST ZH connector model number ZHR-6 or equivalent connector with 6 JST part number SZH-002T-P0.5 26-28 awg contacts or equivalent.

Wire sequence must be as follows:
Pin #1 - Black wire ground potential
Pin #2 - orange wire phase C
Pin #3 - white wire phase B
Pin #4 - green wire phase A
Pin #5 - blue wire temp control, 10 k Thermistor referenced to ground potential
Pin #6 - red wire + 5.0 volts d.c. +/- 10%.
Compatible speed control must use the 6 position JST header part number X-6B-ZR-SMX-TF (where the X denotes the style of the header), or equivalent.

- The power connector has to be clearly marked A, B, C.
A for phase A
B for phase B
C for phase C

d) `05` size specifications
Can:
Overall maximum diameter is 36.02mm measured at whatever point yields the maximum dimension, excluding solder tabs or lead wires. Overall minimum diameter is 34.00mm measured at whatever point yields the minimum dimension, excluding solder tabs or lead wires. Maximum length is 53.00mm measured from the mounting face of the motor to the furthest most point of the end bell, not including solder tabs, lead wires or original manufacturer’s logo or name. Minimum length is 50.00mm measured from the mounting face of the motor to the furthest most point of the end bell, not including solder tabs, lead wires or original manufacturer’s logo or name. Motor mounting holes must be on 1.00- inch (25.40mm) centres.

Stack/Stator:
Stack minimum length 19.30mm, maximum 21.00mm. Stack inside diameter minimum 12.50mm, maximum 16.00mm. If a stack is used then it must be continuous. The laminations have to be one after the other without anything in between. The thickness of the stack plates is 0.35 +/- 0.05mm. All laminations must be of the same material.

Winding:
Only three slot (phase) “Y” wound stators are permitted. No delta wound stators allowed. Only circular (round) pure copper wire permitted. No turn limit.

Rotor:
Shaft diameter must be 0.125 inches (3.175mm). Only one piece, two pole bonded Neodymium or Ferrite magnetic rotors are permitted. Magnet minimum length 23.00mm, maximum 27.00mm. Magnet minimum diameter 12.00mm, maximum 5.50mm.

e) All motors must have the original manufacturer’s logo or name moulded into the end bell.

f) A minimum of two thousand (2000) brushless motors must be available at the time of approval. A minimum of three hundred (300) brushless motors must have been sold to at least three (3) distributors or hobby shops or OEM’s at the time of submittal. The manufacturer has to provide an address of a hobby shop or the like, that any driver who wishes to obtain these motors at the time of the approval can do so. No hybrid (mixing of parts from approved brushless motors) allowed.
aaronkhoo is offline   Reply With Quote
Old 06-06-2005, 12:18 AM   #13
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default INTELLECT BATTERY MANUFACTURER - joins 2005 FEMCA ISTC



Hi everyone,

Just to announce that INTELLECT will be one of the main sponsors for 2005 FEMCA ISTC meeting. Go to http://www.rcmrc.com/istc/download.htm

Invitations are opened to more sponsors. Please email us at [email protected]
aaronkhoo is offline   Reply With Quote
Old 06-09-2005, 07:10 AM   #14
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default Early Birds

Hi Guys,

Thanks, more sponsors are coming in due to the low cost in sponsoring this project. We would like to encourage more participations from sponsors.

Many drivers are signin up, please try to be early, as there are only 150 allocated Seats available to compete in this event.

Cheers

http://www.rcmrc.com/istc/index.htm
aaronkhoo is offline   Reply With Quote
Old 06-14-2005, 10:57 AM   #15
Tech Apprentice
 
Join Date: May 2005
Location: Malaysia
Posts: 54
Default 2005 IFMAR APPROVED PRODUCTS' LIST - BATTERY & MOTOR - 21 May 2005

2005 IFMAR APPROVED PRODUCTS' LIST - BATTERY & MOTOR - 21 May 2005

INTELLECT 3600, INTELLECT 3800, GP 370SCHC, GP 370SCHR, LRP/VTEC 3700 are approved by IFMAR this year 2005 for which will be applicable for the 2005 IFMAR Electric World Championships and also for the 2005 FEMCA ISTC Championship.


2005 IFMAR newly approved Motors: There will be some New interesting serious competition on Brushed and Brushless for this coming meeting & event. Read more about IFMAR Technical Rules on Brushless and Brushed Motors.

LRP/REEDY BRUSHLESS, NOVAK BRUSHLESS,
TRINITY EPIC SHOCK BRUSHED D1 w/D1 "EX" ARMATURE ((2005)
TRINITY EPIC SHOCK BRUSHED w/TORQUE ARMATURE (2005)
TRINITY EPIC SHOCK BRUSHED w/D2 ARMATURE (2005)
TRINITY COBALT BRUSHED w/D1 ARMATURE (2005)
TRINITY COBALT BRUSHED w/D2 ARMATURE (2005)
TRINITY COBALT BRUSHED w/ TORQUE ARMATURE (2005)
aaronkhoo is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
2005 FEMCA 1/10TH ISTC ELECTRIC TOURING CAR CHAMPIONSHIP GT Racer Singapore R/C Racers 8 09-23-2005 09:45 PM
2005 FEMCA 1/10TH ISTC ELECTRIC TOURING CAR CHAMPIONSHIP aaronkhoo Australian Racing 3 07-28-2005 07:52 AM
2005 PRE-FEMCA 1/10TH ISTC CHAMPIONSHIP JeremyLee Singapore R/C Racers 0 07-11-2005 02:18 AM
2005 FEMCA ISTC EP Tire Poll phlim Singapore R/C Racers 1 05-31-2005 10:16 PM
2005 FEMCA 1/10th scale ISTC EP phlim Singapore R/C Racers 1 05-29-2005 07:09 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 06:12 AM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net