Tamiya TA05 Touring Sedan
#8311
Tech Rookie
Picked up an 05ms about 2 months ago (in japan), and was wondering about the 2 sets of front c's that come with the kit. They're labeled 2rl and 4lr, is the difference in caster or camber?
The MS is great, the only weak points I've found are some of the plastic/carbon in the front end and the aluminum turnbuckles on the front. I ditched the front one-way after the first few laps.
The futaba s9550 is great! Unfortunately, the mamba is too much for the local track here...
The MS is great, the only weak points I've found are some of the plastic/carbon in the front end and the aluminum turnbuckles on the front. I ditched the front one-way after the first few laps.
The futaba s9550 is great! Unfortunately, the mamba is too much for the local track here...
#8312
They refer to caster values in degrees..
Hope this helps.
Asil
Hope this helps.
Asil
#8313
Alum. bulkhead
#8314
Tech Adept
i have 2 05rs looking for anyones setups sheets for rubber tire/asphalt/low grip,looked at this thread only found one on carpet,and 0n pg. 244someone ask but nothing ever answered.if i miss one let me know the page #please.or post it for me thank you
#8315
#8316
My basic setup for Asphalt, medium grip was basically kit settings except,
No roll bars
plenty of droop (5 on the gauge front, 3 rear)
Blue Tamiya springs, #450 Much-More oil all round
Seemed to work just fine as a start. Yellow (kit springs) are also OK but can make the car roll a little too much in some corners for my tastes and start to feel a bit sluggish.
No roll bars
plenty of droop (5 on the gauge front, 3 rear)
Blue Tamiya springs, #450 Much-More oil all round
Seemed to work just fine as a start. Yellow (kit springs) are also OK but can make the car roll a little too much in some corners for my tastes and start to feel a bit sluggish.
#8317
asphalt setup
i use white ultra hard springs in the front and blue hard springs at the rear. solved most steering problems. i had a little toe out in the front also. running a tekin g11 pro esc and 10x2t motor. handles very well with a little drag brake set on the esc (:
#8318
would be possible to swap the ta05 chassis with the ta05ms one?would everything else fit back in to it?
thanx
thanx
#8320
so in this case if i buy the ms chassis (top ,bottom),ms motor mount and belts should the rest from the ta05 fit?
#8323
Mounting a Mamba Max
Hi all. Just got my TA05 kit in the mail and look forward to getting on with the build.
Any suggestions on how to mount a Mamba Max in the stock tub? I was planning on just sticking it in the chassis at an angle and be done with it until I can afford to grab one of the carbon chassis. The only other ESC I have on hand is an LRP AI that is even bigger than the Mamba
Any suggestions on how to mount a Mamba Max in the stock tub? I was planning on just sticking it in the chassis at an angle and be done with it until I can afford to grab one of the carbon chassis. The only other ESC I have on hand is an LRP AI that is even bigger than the Mamba
#8324
Hi all. Just got my TA05 kit in the mail and look forward to getting on with the build.
Any suggestions on how to mount a Mamba Max in the stock tub? I was planning on just sticking it in the chassis at an angle and be done with it until I can afford to grab one of the carbon chassis. The only other ESC I have on hand is an LRP AI that is even bigger than the Mamba
Any suggestions on how to mount a Mamba Max in the stock tub? I was planning on just sticking it in the chassis at an angle and be done with it until I can afford to grab one of the carbon chassis. The only other ESC I have on hand is an LRP AI that is even bigger than the Mamba