24LikesAssociated RC 12 R5.2
08-18-2012, 05:38 PM
#16
does any one know where i can buy one
08-23-2012, 08:56 AM
#18
Originally Posted by Rick Hohwart
You can upgrade a little at a time. If you were to install the damper tubes you would have a very similar car to the 12R5.2. Then you can add the other items over time to bring it up to full spec.
08-23-2012, 09:08 AM
#19
Originally Posted by I.T.Guy
I pre-ordered mine from Tower yesterday. Sounds like they had a few in house last week, animals took them all 
..
..Looks like they have only 3 as of 12pm EST!
08-23-2012, 09:11 AM
#20
Mine shipped yesterday 
Strange that other sites don't even have them listed yet
Strange that other sites don't even have them listed yet
08-23-2012, 12:16 PM
#21
Originally Posted by ongbenghui
Hi Hi,
I noticed that the rear lower pod plate got a different part number.
What is the diff ?
R5.2 part number is 4692, R5.1 is 8511
I noticed that the rear lower pod plate got a different part number.
What is the diff ?
R5.2 part number is 4692, R5.1 is 8511
.
08-23-2012, 07:51 PM
#24
Originally Posted by Grassy
Just looking at the new parts list it would be possible to convert your 12R5.1 Inline Version with minimal parts needed.
From what i can see you will need
1 x 4700 Motor Mount Bulkhead
1 x 4701 LR Bulkead
1 x 4702 Motor Mount Brace
1 x 4703 Upper Pod Plate
1 x 4704 Chassis Brace
2 x 4705 Front Bulkhead
1 x 4707 Side Sprig Retainer
1 x 4708 Damper Tube
1 x 4709 Damper Tube Shaft
1 x 8828 Cup Set
1 x 31322 Arm Mount Bushing
I think that is all (someone correct me if there is anything missing)
Kind regards,
Chris
From what i can see you will need
1 x 4700 Motor Mount Bulkhead
1 x 4701 LR Bulkead
1 x 4702 Motor Mount Brace
1 x 4703 Upper Pod Plate
1 x 4704 Chassis Brace
2 x 4705 Front Bulkhead
1 x 4707 Side Sprig Retainer
1 x 4708 Damper Tube
1 x 4709 Damper Tube Shaft
1 x 8828 Cup Set
1 x 31322 Arm Mount Bushing
I think that is all (someone correct me if there is anything missing)
Kind regards,
Chris
08-23-2012, 08:06 PM
#25
Originally Posted by Sean Cochran
The 4692 was new for the inline chassis. So now it's used in the 5.2 kit.
Last edited by ae4ever; 08-23-2012 at 09:39 PM. Reason: wrong part # given
08-23-2012, 08:44 PM
#26
Originally Posted by ae4ever
Are the mounting points for the motor/left side bulkheads different? Would it be possible to install 5.2 motor/left side bulkheads on a R5 lower pod #4602, then use a 5.1 upper pod plate #4688?
08-23-2012, 09:44 PM
#27
Originally Posted by Logi Maker
Upper pod plate is different..
08-23-2012, 11:32 PM
#28
Originally Posted by ae4ever
What do you need the arm bushings for?
08-24-2012, 12:17 AM
#30
Originally Posted by Besercoe
Have you shipped mine yet Chris?
