Hot Bodies Cyclone
thanks Korey your answer was just wat i needed. much appreciated.
Or can try IP 35C 3800Mah
Tech Champion
iTrader: (13)
Tech Master
iTrader: (2)
Hi ,
Could anyone please give me a good gear ratio with a nosram 3.5 with 5 cell mod racing ?
The tracks are medium , and the other track is a bit tighter , so could you advice me on a good ratio please, i know i went on the tighter track and i had a FRD of 9.4 and the motor temp was quite good if i would have gone higher it would have been fine .
But when i went on the medium track , i had a FDR of 9.4 and the motor was hot . so i went to a smaller pinion ( 28 to 27) and i didnt see any difference , then i went to a bigger pinion (27 to 30 and it didnt do any difference , it even made the motor a tiny hoter .
So i dont know what i should do ?
They are both carpet tracks , and the tighter track is only a tiny different then the medium track so i dont get the temp probleme .
Im running the world kit with the 16t pulley .
thanks for any help guys .
Could anyone please give me a good gear ratio with a nosram 3.5 with 5 cell mod racing ?
The tracks are medium , and the other track is a bit tighter , so could you advice me on a good ratio please, i know i went on the tighter track and i had a FRD of 9.4 and the motor temp was quite good if i would have gone higher it would have been fine .
But when i went on the medium track , i had a FDR of 9.4 and the motor was hot . so i went to a smaller pinion ( 28 to 27) and i didnt see any difference , then i went to a bigger pinion (27 to 30 and it didnt do any difference , it even made the motor a tiny hoter .
So i dont know what i should do ?
They are both carpet tracks , and the tighter track is only a tiny different then the medium track so i dont get the temp probleme .
Im running the world kit with the 16t pulley .
thanks for any help guys .
Tech Champion
iTrader: (32)
Hi ,
Could anyone please give me a good gear ratio with a nosram 3.5 with 5 cell mod racing ?
The tracks are medium , and the other track is a bit tighter , so could you advice me on a good ratio please, i know i went on the tighter track and i had a FRD of 9.4 and the motor temp was quite good if i would have gone higher it would have been fine .
But when i went on the medium track , i had a FDR of 9.4 and the motor was hot . so i went to a smaller pinion ( 28 to 27) and i didnt see any difference , then i went to a bigger pinion (27 to 30 and it didnt do any difference , it even made the motor a tiny hoter .
So i dont know what i should do ?
They are both carpet tracks , and the tighter track is only a tiny different then the medium track so i dont get the temp probleme .
Im running the world kit with the 16t pulley .
thanks for any help guys .
Could anyone please give me a good gear ratio with a nosram 3.5 with 5 cell mod racing ?
The tracks are medium , and the other track is a bit tighter , so could you advice me on a good ratio please, i know i went on the tighter track and i had a FRD of 9.4 and the motor temp was quite good if i would have gone higher it would have been fine .
But when i went on the medium track , i had a FDR of 9.4 and the motor was hot . so i went to a smaller pinion ( 28 to 27) and i didnt see any difference , then i went to a bigger pinion (27 to 30 and it didnt do any difference , it even made the motor a tiny hoter .
So i dont know what i should do ?
They are both carpet tracks , and the tighter track is only a tiny different then the medium track so i dont get the temp probleme .
Im running the world kit with the 16t pulley .
thanks for any help guys .
We always ran a 8.2FDR with 5 cell mod.
Tech Champion
iTrader: (32)
hot bodies hpi subura impreza body jmrca 2008
Does anyone know if this body is currently for sale yet? What is the part number?
http://www.rctouring.eu/images/20080926_347590.jpg
http://www.rctouring.eu/images/20080926_347590.jpg
Tech Apprentice
M-Tune
Prototype, if it gets released you'll be able to find it on the HB Website.
Prototype, if it gets released you'll be able to find it on the HB Website.
Suspended
iTrader: (87)
Hi Darrell,
I just like to check with you if your Cyclone TC handles normally after you shaved off 1.5 mm from the alum mount.
Also, I like to confirm that after shaving off 1.5 mm, IP 5000 30C lipo could fit nicely, and the alum part is not touching the top of the lipo battery at all.
Meaning the alum mount's thickness should be approx 2.5 mm now, since it was originally approx 4 mm.
I am thinking of getting the same IP 5000 30C lipo to test as well. I just like to ensure that it could fit my car properly. Your help is greatly appreciated.
Thanks very much.
I just like to check with you if your Cyclone TC handles normally after you shaved off 1.5 mm from the alum mount.
Also, I like to confirm that after shaving off 1.5 mm, IP 5000 30C lipo could fit nicely, and the alum part is not touching the top of the lipo battery at all.
Meaning the alum mount's thickness should be approx 2.5 mm now, since it was originally approx 4 mm.
I am thinking of getting the same IP 5000 30C lipo to test as well. I just like to ensure that it could fit my car properly. Your help is greatly appreciated.
Thanks very much.
To be totally honest, I havent even driven the car on a track yet. My first race is this weekend. I shaved the mount before i got the pack because I thought it would'nt fit from the measurements i had. I took off about 1.5mm but I dont think it will have any effect in handling.
Tech Master
iTrader: (11)
The guys at the 416 thread are posting pictures of their ride, why don't we do the same?
I'm still trying to find a weight plate suitable for the TC using IP3800 35C.
I'm still trying to find a weight plate suitable for the TC using IP3800 35C.