Hot Bodies Cyclone
Tech Elite
iTrader: (28)
How much is reducing chatter worth to you?
ECS Drive Shafts $47.95 EACH
C-Hubs $6.75 EACH
Hinge Pins $3.95
C-Hub Bushings (steel) $11.95
Total approx. $125
It would be interesting to see if HB will come out with an ECS driveshaft design at a reasonable cost. The LOSI LCD is under $35 for a complete set of 2 driveshafts. With spools being used more and more these days a vibration reduction driveshaft design would be a nice upgrade to have available from HB.
ECS Drive Shafts $47.95 EACH
C-Hubs $6.75 EACH
Hinge Pins $3.95
C-Hub Bushings (steel) $11.95
Total approx. $125
It would be interesting to see if HB will come out with an ECS driveshaft design at a reasonable cost. The LOSI LCD is under $35 for a complete set of 2 driveshafts. With spools being used more and more these days a vibration reduction driveshaft design would be a nice upgrade to have available from HB.
Tech Regular
I have the first cyclone the black ver and thinking I should get the cyclone tc
to race on carpet rubber stock what is the gearing I should start at and is the tc a better car on carpet than the black ver and the setup for the tc the same as the black ver if not please direct me to a setup thank you.
to race on carpet rubber stock what is the gearing I should start at and is the tc a better car on carpet than the black ver and the setup for the tc the same as the black ver if not please direct me to a setup thank you.
I have the first cyclone the black ver and thinking I should get the cyclone tc
to race on carpet rubber stock what is the gearing I should start at and is the tc a better car on carpet than the black ver and the setup for the tc the same as the black ver if not please direct me to a setup thank you.
to race on carpet rubber stock what is the gearing I should start at and is the tc a better car on carpet than the black ver and the setup for the tc the same as the black ver if not please direct me to a setup thank you.
Unless you just need a new kit, I would just upgrade to the Pro-Spec diff and maybe the WCE towers for more adjustability. If you are running 17.5 class you could get the 18T pulleys and belts to lower the internal gear ratio a bit.
Set-ups for the TC, WCE and Orginal Cyclones will be very close. The basic geometry of the car hasn't changed over the years. They have just added the ability to make finer adjustments to better suit track conditions.
Tech Elite
iTrader: (28)
How much is reducing chatter worth to you?
ECS Drive Shafts $47.95 EACH
C-Hubs $6.75 EACH
Hinge Pins $3.95
C-Hub Bushings (steel) $11.95
Total approx. $125
It would be interesting to see if HB will come out with an ECS driveshaft design at a reasonable cost. The LOSI LCD is under $35 for a complete set of 2 driveshafts. With spools being used more and more these days a vibration reduction driveshaft design would be a nice upgrade to have available from HB.
ECS Drive Shafts $47.95 EACH
C-Hubs $6.75 EACH
Hinge Pins $3.95
C-Hub Bushings (steel) $11.95
Total approx. $125
It would be interesting to see if HB will come out with an ECS driveshaft design at a reasonable cost. The LOSI LCD is under $35 for a complete set of 2 driveshafts. With spools being used more and more these days a vibration reduction driveshaft design would be a nice upgrade to have available from HB.
Tech Regular
The original Cyclone is still a very competitive car. The weakest link was the diff design. The new Pro-Spec diff took care of that problem.
Unless you just need a new kit, I would just upgrade to the Pro-Spec diff and maybe the WCE towers for more adjustability. If you are running 17.5 class you could get the 18T pulleys and belts to lower the internal gear ratio a bit.
Set-ups for the TC, WCE and Orginal Cyclones will be very close. The basic geometry of the car hasn't changed over the years. They have just added the ability to make finer adjustments to better suit track conditions.
Unless you just need a new kit, I would just upgrade to the Pro-Spec diff and maybe the WCE towers for more adjustability. If you are running 17.5 class you could get the 18T pulleys and belts to lower the internal gear ratio a bit.
Set-ups for the TC, WCE and Orginal Cyclones will be very close. The basic geometry of the car hasn't changed over the years. They have just added the ability to make finer adjustments to better suit track conditions.
on a new kit.
Tech Regular
iTrader: (3)
Thanks to those whom have replied. I appreciate it.
I guess I just want to make sure I pick up a a good chassis in the Cyclone S.
I can't afford the TC spec right now, but just want a good competitive car out of the box. I just don't want to pony up the cash for a Cyclone S and then HB release and 2.0 version. That is why I asked if anyone here has any information if a new or revised Cyclone S will be released in the near future.
Any info?
Thanks,
hs
I guess I just want to make sure I pick up a a good chassis in the Cyclone S.
I can't afford the TC spec right now, but just want a good competitive car out of the box. I just don't want to pony up the cash for a Cyclone S and then HB release and 2.0 version. That is why I asked if anyone here has any information if a new or revised Cyclone S will be released in the near future.
Any info?
Thanks,
hs
Tech Regular
Anyone with info on the new sway bar system that comes on the TC I was looking back a few page and didn't get any info I am looking for, will the new sway bar fit on the first cyclone the black ver? anyone.
Thank you.
Thank you.
Last edited by Ramyuras; 11-11-2008 at 07:27 AM.
Tech Regular
iTrader: (15)
Tech Elite
iTrader: (14)
Interesting discussion on rebound here.
One thing I never understood is how the little force generated by a latex membrane can make such a change once it is added to the stiff springs we are running on the four corners of the cars... when you consider the spring stiffness, that bladder pushes almost nothing... The foams I understand, they suddenly stiffen the suspension big time (closed cells) but the membrane-generated rebound, I just don't get it...
Thanks
Paul
One thing I never understood is how the little force generated by a latex membrane can make such a change once it is added to the stiff springs we are running on the four corners of the cars... when you consider the spring stiffness, that bladder pushes almost nothing... The foams I understand, they suddenly stiffen the suspension big time (closed cells) but the membrane-generated rebound, I just don't get it...
Thanks
Paul
I have noticed that HB team drivers (Hara, Moore) are still using the older swaybar mounting harware over the newer design. Not sure if there is any real reason for this or not.
gearing queston
I recently purchased my first ever electric car. This being a Hotbodies Cyclone S kit. I bought it to do some winter racing indoors and after the completion of my build I can't wait to see this thing in action. My question though, is since this is my first foray into electric I'm not sure what size pinion gear to use w/ the stock 96 tooth spur. I will be running in a stock 27 turn/17.5 class and I was curious to hear some suggestions. I have been told that it is a medium sized track w/ decent staights and enough turns to keep you busy. All i know is if this electric runs as good as I'm hoping there's gonna be alot of nitro stuff for sale here and on the bay.
I haven't used the new swaybar mounting hardware, but it will work with the black version of the Cyclone using either the older or newer A-arm design. Only the mounting harware has changed on the TC. The actual swaybars are still the same as other Cyclones.
I have noticed that HB team drivers (Hara, Moore) are still using the older swaybar mounting harware over the newer design. Not sure if there is any real reason for this or not.
I have noticed that HB team drivers (Hara, Moore) are still using the older swaybar mounting harware over the newer design. Not sure if there is any real reason for this or not.
Tech Champion
iTrader: (32)
once I buy another rear and front bar I will be going back to the old system.
I recently purchased my first ever electric car. This being a Hotbodies Cyclone S kit. I bought it to do some winter racing indoors and after the completion of my build I can't wait to see this thing in action. My question though, is since this is my first foray into electric I'm not sure what size pinion gear to use w/ the stock 96 tooth spur. I will be running in a stock 27 turn/17.5 class and I was curious to hear some suggestions. I have been told that it is a medium sized track w/ decent staights and enough turns to keep you busy. All i know is if this electric runs as good as I'm hoping there's gonna be alot of nitro stuff for sale here and on the bay.
27T CO27 gear 6.5 - 7.0 FDR (with rubber tires) depending on track and your particular motor.
-with a 96T spur you would need between a 33T - 36T pinion.
17.5 needs A LOT more gear. Try down in the 3.5 FDR range. Again, track size, motor brand and batteries all play a role in finding the proper gearing.
-you will need to get a smaller spur to reach the low ratios needed for stock brushless motors. Probably something around 88T spur and some high 50's pinions.
On another note: I have heard the stock C-hubs included with the Cyclone S are rather brittle. You might want to get some of the carbon C-hubs if you break the stock ones. The carbon hubs are the same hubs that come standard on the WCE and TC versions of the Cyclone.
HPI73518 4 degree carbon c-hubs