Hot Bodies Cyclone
Tech Master
iTrader: (23)
Cyclone carpet monster??
OK, I've seen the pics and I've gotta have one! Anybody know where and when the carpet chassis set is going to be available from hot bodies? The Cyclone will be the schizz on the rug with that bad boy!
Jim....your Cyclone is already fast enough.......looks real smooth
Tech Elite
iTrader: (63)
Tech Elite
iTrader: (24)
Tech Elite
iTrader: (24)
Howdy Brant...
Let me firstly assure you.. I am in no way a setup guru, so please take this setup with that understanding...
Front:
Camber: 1.5 deg
Castor: 4 deg
Ride Height: 5.0mm
Droop: 5.0mm
Front Drive: Spool
Stabiliser: 1.4mm
Toe Angle: 1 deg
Top Shock Location: 3
Bottom Shock Location: 1
Inner Camber Link location: 1
Inner Camber Link Spacers: 2.0mm
Front Bottom Roll Centre Spacers: 1.5mm
Rear Bottom Roll Centre Spacers: 1.5mm
Pivot Block: 2.5
Ackerman: 4.0mm
Shock Piston: 3 x 1.1mm
Shock Oil: 40wt
Shock Spring: Pink
Shock Foam: none
Shock Rebound: none
Rear:
Camber: 1.5 deg
Ride Height: 5.5mm
Droop: 5.0mm
Stabiliser: 1.2mm
Toe Angle: 1 deg
Top Shock Location: 3
Bottom Shock Location: 2
Inner Camber Link location: 1
Inner Camber Link Spacers: 1.5mm
Outer Camber Link Spacers: 0.0mm
Front Bottom Roll Centre Spacers: 1.5mm
Rear Bottom Roll Centre Spacers: 1.5mm
Pivot Block: 3.0
Shock Piston: 3 x 1.1mm
Shock Oil: 40wt
Shock Spring: Silver
Shock Foam: none
Shock Rebound: none
Bolt on whatever tyre/insert/rim that works locally and usually use the Mazda 6 or Speed 6. I usually take this setup with me everywhere and start tuning the car in with the shocks first by changing the piston and fluid, eg. Tamiya 3 x 1.0mm or HB 2 x 1.2mm and fluid by 30wt up to 45wt. Then juggle the Droop, and Ride Height before going to anything else on the car.
For the Titanium Screws; the "Square RC" screws have been very tough and reliable for me... Part #: SHB-52… for about 3,780Yen.
Hope this helps...
Regards,
Peter
Let me firstly assure you.. I am in no way a setup guru, so please take this setup with that understanding...
Front:
Camber: 1.5 deg
Castor: 4 deg
Ride Height: 5.0mm
Droop: 5.0mm
Front Drive: Spool
Stabiliser: 1.4mm
Toe Angle: 1 deg
Top Shock Location: 3
Bottom Shock Location: 1
Inner Camber Link location: 1
Inner Camber Link Spacers: 2.0mm
Front Bottom Roll Centre Spacers: 1.5mm
Rear Bottom Roll Centre Spacers: 1.5mm
Pivot Block: 2.5
Ackerman: 4.0mm
Shock Piston: 3 x 1.1mm
Shock Oil: 40wt
Shock Spring: Pink
Shock Foam: none
Shock Rebound: none
Rear:
Camber: 1.5 deg
Ride Height: 5.5mm
Droop: 5.0mm
Stabiliser: 1.2mm
Toe Angle: 1 deg
Top Shock Location: 3
Bottom Shock Location: 2
Inner Camber Link location: 1
Inner Camber Link Spacers: 1.5mm
Outer Camber Link Spacers: 0.0mm
Front Bottom Roll Centre Spacers: 1.5mm
Rear Bottom Roll Centre Spacers: 1.5mm
Pivot Block: 3.0
Shock Piston: 3 x 1.1mm
Shock Oil: 40wt
Shock Spring: Silver
Shock Foam: none
Shock Rebound: none
Bolt on whatever tyre/insert/rim that works locally and usually use the Mazda 6 or Speed 6. I usually take this setup with me everywhere and start tuning the car in with the shocks first by changing the piston and fluid, eg. Tamiya 3 x 1.0mm or HB 2 x 1.2mm and fluid by 30wt up to 45wt. Then juggle the Droop, and Ride Height before going to anything else on the car.
For the Titanium Screws; the "Square RC" screws have been very tough and reliable for me... Part #: SHB-52… for about 3,780Yen.
Hope this helps...
Regards,
Peter
I cant find it, but I know I saw something about using a 2.6 mm (I think) screw from HB
What was the screw? And what thrust washers, balls do I use?
Also, do xray knuckles, and or c hubs fit the cyclone? Are they any stronger?
Thanks
What was the screw? And what thrust washers, balls do I use?
Also, do xray knuckles, and or c hubs fit the cyclone? Are they any stronger?
Thanks
Tech Elite
iTrader: (63)
I still cant find them hb 3 x 1.1mm pistons anywhere?????
can some one give me a direct link, please........
can some one give me a direct link, please........
Tech Elite
iTrader: (24)
Champ RC website is ordinary, but just email them with the bits you want and they will get back to you within 2 or 3 days... (Monday's: they are closed)
PS> they understand and reply in english so there's no problems there either.
Hope this helps,
Regards,
Peter
Tech Elite
iTrader: (50)
CYCLONE AFTERMARKET PARTS HELP
Can anyone help me with some parts locations.
Jet alum. 4 deg. c-hubs. black
jet or other Alum steering blocks
p-dub or parma bumper and a kydex bumper
rc champ has never replied to my questions in email form about these so I'm looking elsewhere.
Thanks,
Jason
Jet alum. 4 deg. c-hubs. black
jet or other Alum steering blocks
p-dub or parma bumper and a kydex bumper
rc champ has never replied to my questions in email form about these so I'm looking elsewhere.
Thanks,
Jason
Tech Master
iTrader: (11)
Tech Elite
iTrader: (26)
Need your help fellas:
Need 3 hole pistons for my WCE Cyclone shocks. Anyone know is the serpent S400 pistons work on the Cyclone Shocks or maybe Tamiya TRF 415 pistons?
I really need some 3 hole pistons...maybe Schumacher MI3 pistons?
Help!!!
Need 3 hole pistons for my WCE Cyclone shocks. Anyone know is the serpent S400 pistons work on the Cyclone Shocks or maybe Tamiya TRF 415 pistons?
I really need some 3 hole pistons...maybe Schumacher MI3 pistons?
Help!!!
Super Moderator
iTrader: (239)
tamiya or schumacher work just fine
Tech Apprentice
go into your hobby shop (or ring them) and ask for them to order HB73524.
just ask your hobby shop.
Warren
just ask your hobby shop.
Warren
Its just if I go all alu, then wont that stuff bend, and break ball studs?